LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2002 >> Sentra SE-R, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 366 (Transfer Case) >> Trouble Diagnosis For System >> ATP Switch >> Diagnostic Procedure

Diagnostic Procedure

WARNING: This page is about a different car, the 2004 Nissan Titan. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK ATP SWITCH SIGNAL (With CONSULT-II) 
    1. Start engine.
    2. Select "DATA MONITOR" mode for "ALL MODE AWD/4WD" with CONSULT-II.
    3. Read out the value of "ATP SWITCH".
    Fig 1: Test Conditions
    G00728826Courtesy of NISSAN MOTOR CO., U.S.A.
    Fig 2: CONSULT-II Display
    G00728827Courtesy of NISSAN MOTOR CO., U.S.A.

    Without CONSULT-II 

    1. Start engine.
    2. Check voltage between transfer control unit harness connector terminal and ground.
      Fig 3: Test Conditions
      G00728828Courtesy of NISSAN MOTOR CO., U.S.A.
      Fig 4: Checking Voltage
      G00728829Courtesy of NISSAN MOTOR CO., U.S.A.

      OK or NG 

    1. OK: GO TO  5.
    2. NG: GO TO 2.
  2. CHECK HARNESS BETWEEN TRANSFER CONTROL UNIT AND ATP SWITCH 
    1. Turn ignition switch "OFF".
    2. Disconnect transfer control unit harness connector and the ATP switch harness connector.
    3. Check continuity between transfer control unit harness connector E142 terminal 23 (R/B) and ATP switch harness connector F55 terminal 8 (R/B).

    Continuity should exist. 

    Also check harness for short to ground and short to power.

    OK or NG 

    1. OK: GO TO 3.
    2. NG: Repair or replace damaged parts.
    Fig 5: Checking Continuity
    G00728830Courtesy of NISSAN MOTOR CO., U.S.A.
  3. CHECK GROUND CIRCUIT 
    1. Turn ignition switch "OFF".
    2. Disconnect ATP switch harness connector.
    3. Check continuity between ATP switch harness connector F55 terminal 9 (B) and ground.

    Continuity should exist. 

    Also check harness for short to ground and short to power.

    OK or NG 

    1. OK: GO TO 4.
    2. NG: Repair open circuit or short to ground or short to power in harness or connectors.
    Fig 6: Checking Continuity
    G00728831Courtesy of NISSAN MOTOR CO., U.S.A.
  4. CHECK ATP SWITCH 
    1. Turn ignition switch "OFF".
    2. Disconnect ATP switch harness connector.
    3. Remove ATP switch.
    4. Push and release ATP switch and check continuity between ATP switch harness connector F55 terminals 8 and 9.
    Fig 7: Continuity Chart
    G00728832Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    1. OK: GO TO 5.
    2. NG: Replace ATP switch.
    Fig 8: Checking Continuity
    G00728833Courtesy of NISSAN MOTOR CO., U.S.A.
  5. CHECK TRANSFER CONTROL UNIT 

    Check transfer control unit input/output signal. Refer to TRANSFER CONTROL UNIT INPUT/OUTPUT SIGNAL REFERENCE VALUES .

    OK or NG 

    1. OK: GO TO 6.
    2. NG: Check transfer control unit pin terminals for damage or loose connection with harness connector. If any items are damaged, repair or replace damaged parts.
  6. CHECK ATP WARNING LAMP 
    1. Turn ignition switch "ON". (Do not start engine.)
    2. Set the selector lever to "P" position and engage the parking brake.
    3. Switch 4WD shift switch from 4H to 4LO or 4LO to 4H.

    Does ATP warning lamp "ON", while actuator motor is operating? 

    1. YES: INSPECTION END 
    2. NO: Go to ATP WARNING LAMP DOES NOT TURN ON .