LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2002 >> Sentra SE-R, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 366 (Transfer Case) >> Trouble Diagnosis For System >> 4WD Shift Switch >> Diagnostic Procedure

Diagnostic Procedure

WARNING: This page is about a different car, the 2004 Nissan Titan. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK 4WD SHIFT SWITCH SIGNAL (With CONSULT-II) 
    1. Turn ignition switch "ON".
    2. Select "DATA MONITOR" mode for "ALL MODE AWD/4WD" with CONSULT-II.
    3. Read out ON/OFF switching action of the "2WD SWITCH", "4H SWITCH", "4L SWITCH" with operating 4WD shift switch.
    Fig 1: CONSULT-II Display
    G00728764Courtesy of NISSAN MOTOR CO., U.S.A.

    (Without CONSULT-II) 

    1. Turn ignition switch "ON".
    2. Check voltage between transfer control unit harness connector terminals and ground.
    Fig 2: Test Conditions
    G00728765Courtesy of NISSAN MOTOR CO., U.S.A.
    Fig 3: Checking Voltage
    G00728766Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    1. OK: GO TO 5.
    2. NG: GO TO 2.
  2. CHECK 4WD SHIFT SWITCH POWER SUPPLY CIRCUIT 
    1. Turn ignition switch "ON".
    2. Disconnect 4WD shift switch harness connector.
    3. Check voltage between 4WD shift switch harness connector terminal 1 and ground.
      Fig 4: Test Conditions
      G00728767Courtesy of NISSAN MOTOR CO., U.S.A.
      Fig 5: Checking Voltage
      G00728768Courtesy of NISSAN MOTOR CO., U.S.A.
    4. Turn ignition switch "OFF".
    5. Check voltage between 4WD shift switch harness connector terminal 1 and ground.
    Fig 6: Test Conditions
    G00728769Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    1. OK: GO TO 3.
    2. NG: Check the following. If any items are damaged, repair or replace damaged parts.
    Fig 7: Checking Voltage
    G00728770Courtesy of NISSAN MOTOR CO., U.S.A.
    • 10A fuse [No. 26 or 59 located in the IPDM E/R]
    • Harness for short or open between battery and 4WD shift switch harness connector terminal 1
    • Harness for short or open between ignition switch and transfer relay 1 harness connector E46 terminal 2 (L/W)
    • Harness for short or open between transfer relay 1 harness connector E46 terminal 1 (B) and ground.
    • Battery and ignition switch. Refer to POWER DISTRIBUTION in SYSTEM WIRING DIAGRAMS - TITAN article in ELECTRICAL. .
    • Transfer relay 1. Refer to COMPONENT INSPECTION .
  3. CHECK HARNESS BETWEEN 4WD SHIFT SWITCH AND TRANSFER CONTROL UNIT 
    1. Turn ignition switch "OFF".
    2. Disconnect transfer control unit harness connector and the 4WD shift switch harness connector.
    3. Check continuity between the following terminals.
    • Transfer control unit harness connector E142 terminal 14 (G/W) and 4WD shift switch harness connector M141 terminal 3 (G/W).
    • Transfer control unit harness connector E142 terminal 15 (O) and 4WD shift switch harness connector M141 terminal 5 (O).
    • Transfer control unit harness connector E142 terminal 16 (R) and 4WD shift switch harness connector M141 terminal 6 (R).

    Continuity should exist. 

    Also check harness for short to ground and short to power.

    OK or NG 

    1. OK: GO TO 4.
    2. NG: Repair or replace damaged parts.
    Fig 8: Checking Continuity
    G00728771Courtesy of NISSAN MOTOR CO., U.S.A.
  4. CHECK 4WD SHIFT SWITCH 
    1. Turn ignition switch "OFF".
    2. Disconnect 4WD shift switch harness connector.
    3. Operate 4WD shift switch and check continuity between 4WD shift switch harness connector terminals.
    Fig 9: Continuity Chart
    G00728772Courtesy of NISSAN MOTOR CO., U.S.A.
    Fig 10: Checking Continuity
    G00728773Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    1. OK: GO TO 5.
    2. NG: Replace 4WD shift switch.
  5. CHECK TRANSFER CONTROL UNIT 

    Check transfer control unit input/output signal. Refer to TRANSFER CONTROL UNIT INPUT/OUTPUT SIGNAL REFERENCE VALUES .

    OK or NG 

    1. OK: GO TO 6.
    2. NG: Check transfer control unit pin terminals for damage or loose connection with harness connector.

      If any items are damaged, repair or replace damaged parts.

  6. CHECK DTC 

    Perform the self-diagnosis, after driving a vehicle for a while.

    OK or NG 

    1. OK: INSPECTION END 
    2. NG: Replace transfer control unit. Refer to TRANSFER CONTROL UNIT .