LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2002 >> Sentra SE-R, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 366 (Transfer Case) >> Trouble Diagnosis For System >> 4LO Switch >> Diagnostic Procedure

Diagnostic Procedure

WARNING: This page is about a different car, the 2004 Nissan Titan. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK 4LO POSITION SWITCH SIGNAL (With CONSULT-II) 
    1. Start engine.
    2. Select "DATA MONITOR" mode for "ALL MODE AWD/4WD" with CONSULT-II.
    3. Read out the value of "4L POSI SW".
    Fig 1: Test Conditions
    G00728752Courtesy of NISSAN MOTOR CO., U.S.A.
    Fig 2: CONSULT-II Display
    G00728753Courtesy of NISSAN MOTOR CO., U.S.A.

    CHECK 4LO POSITION SWITCH SIGNAL (Without CONSULT-II) 

    1. Start engine.
    2. Check voltage between transfer control unit harness connector terminal and ground.
    Fig 3: Test Conditions
    G00728754Courtesy of NISSAN MOTOR CO., U.S.A.
    Fig 4: Checking Voltage
    G00728755Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    1. OK: GO TO 5.
    2. NG: GO TO 2.
  2. CHECK HARNESS BETWEEN TRANSFER CONTROL UNIT AND 4LO SWITCH 
    1. Turn ignition switch "OFF".
    2. Disconnect transfer control unit harness connector and the 4LO switch harness connector.
    3. Check continuity between transfer control unit harness connector E142 terminal 24 (V) and 4LO switch harness connector F60 terminal 13 (V).

    Continuity should exist. 

    Also check harness for short to ground and short to power.

    OK or NG 

    1. OK: GO TO 3.
    2. NG: Repair or replace damaged parts.
    Fig 5: Checking Continuity
    G00728756Courtesy of NISSAN MOTOR CO., U.S.A.
  3. CHECK GROUND CIRCUIT 
    1. Turn ignition switch "OFF".
    2. Disconnect 4LO switch harness connector.
    3. Check continuity between 4LO switch harness connector F60 terminal 12 (B) and ground.

    Continuity should exist. 

    Also check harness for short to ground and short to power.

    OK or NG 

    1. OK: GO TO 4.
    2. NG: Repair open circuit or short to ground or short to power in harness or connectors.
    Fig 6: Checking Continuity
    G00728757Courtesy of NISSAN MOTOR CO., U.S.A.
  4. CHECK 4LO SWITCH 
    1. Turn ignition switch "OFF".
    2. Disconnect 4LO switch harness connector.
    3. Remove 4LO switch.
    4. Push and release 4LO switch and check continuity between 4LO switch harness connector F60 terminals 12 and 13.
    Fig 7: Continuity Chart
    G00728758Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    1. OK: GO TO 5.
    2. NG: Replace 4LO switch.
    Fig 8: Checking Continuity
    G00728759Courtesy of NISSAN MOTOR CO., U.S.A.
  5. CHECK TRANSFER CONTROL UNIT 

    Check transfer control unit input/output signal. Refer to TRANSFER CONTROL UNIT INPUT/OUTPUT SIGNAL REFERENCE VALUES .

    OK or NG 

    1. OK: GO TO 6.
    2. NG: Check transfer control unit pin terminals for damage or loose connection with harness connector.

      If any items are damaged, repair or replace damaged parts.

  6. CHECK DTC 

    Perform the self-diagnosis, after driving a vehicle for a while.

    OK or NG 

    1. OK: INSPECTION END 
    2. NG: Replace transfer control unit. Refer to TRANSFER CONTROL UNIT .