LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 1992 >> Sentra SE-R >> Repair and Diagnosis >> Quick Lookups >> Technical Bulletins >> Technical Service Bulletins >> Other Variant >> HVAC Control Systems >> Essential Tool: Engine Coolant Refill Tool (NTB02-011A)

Essential Tool: Engine Coolant Refill Tool (NTB02-011A)

WARNING: This page is about the Sentra E, 2D Sedan, Automatic, which is a different variant/trim than selected.
Publication date: 2002-03-11
Reference number: NTB02-011A
Supersedes refnos: NTB02-011

ESSENTIAL TOOL: ENGINE COOLANT REFILL TOOL

ESSENTIAL TOOL: ENGINE COOLANT REFILL TOOL

TECHNICAL SERVICE BULLETIN

Reference Number(s): NTB02-011A, Date of Issue:  March 11, 2002
NISSAN: All Nissan
CLASSIFICATION: TE02-001A
SECTION: Tool and Equipment
APPLIED VEHICLE(S): All Nissan
Superceded Bulletin(s): NTB02-011
NOTE: This bulletin amends NTB02-011. This version has the addition of a Service Procedure. Please discard all paper copies of the earlier bulletin.

SERVICE INFORMATION

If for any reason the vehicle's cooling system needs to be filled with coolant due to a service repair or maintenance, use the Coolant Refill Tool #J-45695.

To ensure the tool is used correctly, refer to the Operating Instructions supplied with the tool and the Service Procedure in this Bulletin.

Refer to ESSENTIAL TOOL SHIPMENT  for additional information.

This special tool is "Essential" and was automatically sent to all Nissan dealers.

Additional tools can be ordered from Tech-Mate.

SERVICE PROCEDURE

Refer to the Operating Instructions supplied with the tool for complete refill procedure. Key points to ensure the cooling system is purged of air bubbles are as follows:

Always start with an Empty Radiator.

  1. For Step 2 of the Operating Instructions:
    • To hold the coolant mixture supply, use a clean bucket or other suitable container that is larger than the cooling system's total capacity.
    • The amount of coolant mixture in the refill supply must be more than needed to fill the system completely.
    • This will help avoid pulling in air at the end of the refilling procedure.
      NOTE:
      • See the appropriate Service Manual for cooling system refill capacity.
      • Use Genuine NISSAN Anti-freeze Coolant or equivalent, mixed 50/50 with distilled water or demineralized water.
  2. For step 3 of the Operating Instructions:
    • Make sure to Purge all air from the Refill Tube (intake hose) before beginning the refill process.
      NOTE: The Venturi will NOT be harmed if some coolant goes through it during the air purge process.
    • Place the container of coolant mixture above the level of the radiator during the refill process.
    Fig 1: Engine Long Life Coolant Refill Tool
    G00224892

ESSENTIAL TOOL SHIPMENT

TO: Dealer Principal and Dealer Service Manager

2001 Nissan

EG-130-01-13

The following special service tool has been classified essential by Nissan North America, Inc.

J-45695

Coolant Refill Tool

Application: Universal

NOTE: Airlocks in the cooling system of today's vehicles can cause engine overheating, poor heater performance, or unwanted noise. This tool was developed specifically for Nissan vehicles to eliminate airlocks without repeated, time consuming, warm up and cool down cycles. Elevating the front of the vehicle is also not necessary. It has a Nissan specific radiator cap and a double venturi that enables it to pull a deeper vacuum than competitive products. This tool also has two hose connections, which allows you to purge air from the refill hose before it is introduced into the cooling system. A leak check can be performed by monitoring the vacuum gauge prior to adding the new coolant and water solution. The coolant refill tool saves time during coolant changes, while reducing the risk of a comeback after the service.