Engine DRIVEABILITY Diagnostic Procedures:Supplement (NTB94-018)
WARNING: This page is about the Sentra E, 2D Sedan, Automatic, which is a different variant/trim than selected.
Publication date: 1994-02-15Reference number: NTB94-018
ENGINE DRIVEABILITY DIAGNOSTIC PROCEDURES:SUPPLEMENT
TECHNICAL SERVICE BULLETIN
Reference Number(s): NTB94-018, Date of Issue:
February 15, 1994
ENGINE DRIVEABILITY SUPPLEMENTAL DIAGNOSTIC PROCEDURES
Model(s): All CONSULT-compatible models
Classification: EF & EC94-003
Section: Engine Fuel & Emission Control
Bulletin No.: NTB94-018
Date: February 15, 1994
SERVICE INFORMATION
The attached diagnostic tables are designed to be used as a Supplement to Service Manual trouble diagnostic procedures. The tables take advantage of CONSULT to broaden the diagnostic process and make it more efficient. The points below highlight some of the advantages and details of using the tables to supplement Service manual diagnosis.
- The Basic Inspection procedure now includes a Fuel Pressure Check, CONSULT Function Test, and a reorganized CONSULT Diagnostic procedure.
- Items with two ** asterisks are the recommended CONSULT diagnostic procedures.
- Items with three *** asterisks indicate that an additional diagnostic procedure has been added to the Service Manual diagnostic procedure.
- Items continue to be selected by Service Manual. symptom-related diagnostics.
- Additional items have been inserted that previously have not been listed in the Service Manual for symptom-related diagnostic procedures.
- The information is a quick-reference supplement for the Service Manual. The Service Manual should continue to be the primary source of information for trouble diagnosis.
- Individual Diagnostic Procedures 21-45 may indicate that the Service Manual should be referenced for additional diagnostic information.
BASIC INSPECTION PROCEDURE
BASIC INSPECTION PROCEDURE CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | n/a |
| Step 1 | Before Starting |
| Step 2 | Connect CONSULT to the Vehicle |
| Step 3 | Does engine start? Y = Step 4 N = Step 10 |
| Step 4 | Check Fuel Pressure *** |
| Step 5 | Check Ignition Timing |
| Step 6 | Read Self Diagnosis Results |
| Step 7 | CONSULT Function Test *** ** |
| Step 8 | Check Idle Adjustment screw initial RPM ** |
| Step 9 | Check Throttle Position Sensor Idle Position ** |
| Step 10 | Check Switch Imput Signal (Main Signals) *** ** |
| ** = Test is Conducted Using CONSULT | |
| *** = Additonal Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURES
DIAGNOSTIC PROCEDURE #1 - HIGH IDLING AFTER WARM-UP CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | IS, ISH, ISR No return to idle High Idle |
| Step 1 | Check IAA Unit |
| Step 2 | Check Throttle Linkage |
| Step 3 | CONSULT Data Monitor Main Signals *** ** |
| Step 4 | Check Intake Air Leak ** |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #2 - HUNTING CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | IH, IHF, IHH, IHS Hesitation, Flat Spot Surging |
| Step 1 | CONSULT Data Monitor Main Signals *** ** |
| Step 2 | Perform Power Balance Test ** |
| Step 3 | Check Heated Oxygen Sensor ** |
| Step 4 | Check Intake Air Leak |
| Step 5 | Check EGR Valve |
| Step 6 | Check Spark Plugs |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #3 - UNSTABLE IDLE CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | IC Rough Idle |
| Step 1 | CONSULT Data Monitor Main Signals *** ** |
| Step 2 | Check Idle Adjustment Screw Clogging ** |
| Step 3 | Check Heated Oxygen Sensor ** |
| Step 4 | Perform Power Balance Test ** |
| Step 5 | Check EGR Valve |
| Step 6 | Check for Intake Air Leak |
| Step 7 | Check Fuel Pressure |
| Step 8 | Check Injector |
| Step 9 | Check Ignition Spark/ Check Spark Plugs |
| Step 10 | Check Compression Pressure |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #4 - HARD TO START WHEN COLD CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | IA, IAC, IAH, IAN, IAS Hard no start when cold |
| Step 1 | Check Battery and Starter |
| Step 2 | Check Fuel Pressure |
| Step 3 | CONSULT Data Monitor Main Signals *** ** |
| Step 4 | Check IACV - Air Regulator and IACV-ACC Valve |
| Step 5 | Check Injector |
| Step 6 | Check Ignition Spark |
| Step 7 | Check Spark Plugs |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #5 - HARD TO START WHEN HOT CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | IB, IBC, IBH, IBN, IBS Hard to start warm |
| Step 1 | Check Battery and Starter |
| Step 2 | Check Fuel Pressure |
| Step 3 | CONSULT Data Monitor Main Signals *** ** |
| Step 4 | Check Injector |
| Step 5 | Check Injector for Leakage *** |
| Step 6 | Check Ignition Spark |
| Step 7 | Check Fuel Vapor/Quality |
| Step 8 | Check Spark Plugs |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #6 - HARD TO START UNDER NORMAL CONDITIONS CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | IB Hard to start warm |
| Step 1 | Check Battery and Starter |
| Step 2 | Check Fuel Pressure |
| Step 3 | CONSULT Data Monitor Main Signals *** ** |
| Step 4 | Check Injector for Leakage |
| Step 5 | Check Injector |
| Step 6 | Check Ignition Spark/ Check Plugs |
| Step 7 | Check EGR Valve |
| Step 8 | Check ECM Harness Connector |
| Step 9 | Check ECM Power Supply and Ground Circuit |
| Step 10 | Try a Known Good ECM |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #7 - HESITATION WHEN HOT CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | IH, IHF, IHH, IHS Hesitation, Flat Spot Surging |
| Step 1 | CONSULT Data Monitor Main Signals *** ** |
| Step 2 | Perform Power Balance Test ** |
| Step 3 | Check Fuel Pressure *** |
| Step 4 | Check Fuel Vapor/Quality |
| Step 5 | Check For Intake Air Leak *** |
| Step 6 | Check Canister Purge *** |
| Step 7 | Check Spark Plugs *** |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #8 - HESITATION WHEN COLD CHART
| Step | Procedure |
| NMC Related Symptom(s) | IH, IHF, IHH, IHS Hesitation, Flat Spot Surging |
| Step 1 | CONSULT Data Monitor Main Signals *** ** |
| Step 2 | Perform Power Balance Test ** |
| Step 3 | Check Fuel Pressure *** |
| Step 4 | Check Spark Plugs |
| Step 5 | Check For Intake Air Leak |
| Step 6 | Check Injector for Leakage |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #9 - HESITATION UNDER NORMAL CONDITIONS CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | IH, IHF, IHH, IHS Hesitation, Flat Spot Surging |
| Step 1 | CONSULT Data Monitor Main Signals *** ** |
| Step 2 | Check Heated Oxygen Sensor ** |
| Step 3 | Perform Power Balance Test ** |
| Step 4 | Check Fuel Pressure *** |
| Step 5 | Check Injector for Leakage *** |
| Step 6 | Check For Intake Air Leak |
| Step 7 | Check Canister Purge |
| Step 8 | Check Spark Plugs |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #10 - ENGINE STALLS WHEN TURNING CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | IF Engine Stalls |
| Step 1 | Check Fuel Level |
| Step 2 | Check Idle Adjustment Screw Initial RPM *** ** |
| Step 3 | CONSULT Data Monitor Main Signals *** ** |
| Step 4 | Perform Power Balance Test ** |
| Step 5 | Check Injector |
| Step 6 | Check Ignition Spark |
| Step 7 | Check Fuel Pressure |
| Step 8 | Check ECM Harness Connector |
| Step 9 | Check ECM Power Supply and Ground Circuit |
| Step 10 | Try a Known Good ECM |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #11 - ENGINE STALLS WHEN HOT CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | IF Engine Stalls |
| Step 1 | Check Fuel Vapor |
| Step 2 | Check Fuel Pressure |
| Step 3 | CONSULT Data Monitor Main Signals *** ** |
| Step 4 | Check Idle Adjustment Screw Initial RPM *** ** |
| Step 5 | Perform Power Balance Test ** |
| Step 6 | Check Injector |
| Step 7 | Check Ignition Spark |
| Step 8 | Check ECM Harness Connector |
| Step 9 | Check ECM Power Supply and Ground Circuit |
| Step 10 | Try a Known Good ECM |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #12 - ENGINE STALLS WHEN COLD CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | If Engine Stalls |
| Step 1 | Check IACV Air Regulator and IACV-ACC Valve |
| Step 2 | Check Fuel Pressure |
| Step 3 | CONSULT Data Monitor Main Signals *** ** |
| Step 4 | Perform Power Balance Test *** ** |
| Step 5 | Check Injector |
| Step 6 | Check Injector Spark Check Spark Plugs |
| Step 7 | Clean Fuel Injectors *** |
| Step 8 | Check ECM Harness Connector |
| Step 9 | Check ECM Power Supply and Ground Circuit |
| Step 10 | Try a Known Good ECM |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #13 - ENGINE STALLS WHEN ACCELERATED FAST CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | If Engine Stalls |
| Step 1 | CONSULT Data Monitor Main Signals *** ** |
| Step 2 | Perform Power Balance Test ** |
| Step 3 | Check IACV Air Regulator and IACV-ACC ** |
| Step 4 | Check Fuel Pressure |
| Step 5 | Check Injectors |
| Step 6 | Clean Fuel Injectors *** |
| Step 7 | Check Ignition Spark |
| Step 8 | Check ECM Harness Connector |
| Step 9 | Check ECM Power Supply and Ground Circuit |
| Step 10 | Try a Known Good ECM |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #14 - ENGINE STALLS AFTER DECELERATING CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | IF Engine Stalls |
| Step 1 | Check IACV Air Regulator and IACV-ACC ** |
| Step 2 | CONSULT Data Monitor Main Signals *** ** |
| Step 3 | Check Heated Oxygen Sensor ** |
| Step 4 | Perform Power Balance Test ** |
| Step 5 | Check Injectors |
| Step 6 | Check Ignition Spark |
| Step 7 | Check Fuel Pressure |
| Step 8 | Check ECM Harness Connector |
| Step 9 | Check ECM Power Supply and Ground Circuit |
| Step 10 | Try a Known Good ECM |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #15 - ENGINE STALLS WHEN ACCEL/CRUISING CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | IF Engine Stalls |
| Step 1 | Check Fuel Pressure |
| Step 2 | CONSULT Data Monitor Main Signals *** ** |
| Step 3 | Perform Power Balance Test ** |
| Step 4 | Check Ignition Spark |
| Step 5 | Check Injectors |
| Step 6 | Check Fuel Injectors *** |
| Step 7 | Check for Intake Air Leak |
| Step 8 | Check ECM Harness Connector |
| Step 9 | Check ECM Power Supply and Ground Circuit |
| Step 10 | Try a Known Good ECM |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #16 - ENGINE STALLS UNDER ELECTRICAL LOAD CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | IF Engine Stalls |
| Step 1 | Check Battery and Alternator |
| Step 2 | Check IACV Air Regulator and IACV-AAC Valve *** ** |
| Step 3 | CONSULT Data Monitor Main Signals *** ** |
| Step 4 | Perform Power Balance Test ** |
| Step 5 | Check Fuel Pressure |
| Step 6 | Check Injectors |
| Step 7 | Check Ignition Spark |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #17 - LACK OF POWER AND STUMBLE CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | IH, IHF, IHH, IHS Hesitation, Flat Spot Surging |
| Step 1 | Check Fuel Pressure |
| Step 2 | CONSULT Data Monitor Main Signals *** ** |
| Step 3 | Perform Power Balance Test ** |
| Step 4 | Check Spark Plugs *** |
| Step 5 | Check for Intake Air Leak |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #18 - KNOCK CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | IM Spark Knock (pinging) |
| Step 1 | Check Ignition Timing With a Timing Light |
| Step 2 | CONSULT Data Monitor Main Signals *** ** |
| Step 3 | Check EGRC- Solenoid Valve ** |
| Step 4 | Check EGR Operation |
| Step 5 | Check Vacuum Hoses |
| Step 6 | Check for Intake Air Leak *** |
| Step 7 | Check for Oil Leak to Combustion Chamber |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #19 - SURGE CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | IH, IHF, IHH, IHS Hesitation, Flat Spot Surging |
| Step 1 | CONSULT Data Monitor Main Signals *** ** |
| Step 2 | Check Heated Oxygen Sensor ** |
| Step 3 | Perform Fuel Pressure *** |
| Step 4 | Check Fuel Vapor *** |
| Step 5 | Check/Clean Injector *** |
| Step 6 | Check EGR Valve |
| Step 7 | Check ECM Power Supply and Ground Circuit |
| Step 8 | Try a Known Good ECM |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #20 - BACKFIRE THROUGH THE INTAKE CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | IJ Backfire |
| Step 1 | CONSULT Data Monitor Main Signals *** ** |
| Step 2 | Check Fuel Pressure *** |
| Step 3 | Check Intake Air Leak |
| Step 4 | Check Ignition Timing With a Timing Light |
| Step 5 | Check Spark Plugs |
| Step 6 | Check Injector *** |
| Step 7 | Clean Fuel Injector *** |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #21 - BACKFIRE THROUGH THE EXHAUST CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | IJ Afterfire |
| Step 1 | Check Engine Coolant Temperature Sensor ** |
| Step 2 | CONSULT Data Monitor Main Signals *** ** |
| Step 3 | Check Injector Leak *** |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #22 - MAIN POWER SUPPLY & GROUND CIRCUIT CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | Specific symptom depend upon individual incident |
| Step 1 | A Check Power Supply |
| Step 2 | B Check Ground Circuit |
| Step 3 | C Check Harness Continuity Between ECCS Relay and ECM |
| Step 4 | D Check Voltage Between ECCS Relay and ECM |
| Step 5 | E Check Voltage Between ECM and Ground |
| Step 6 | F Check Ground Circuit |
| Step 7 | G Check Output Signal Circuit |
| Step 8 | H Check Imput Signal Circuit |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #23 - CAMSHAFT POSITION SENSOR CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | Specific symptom depend upon individual incident |
| Step 1 | A Check Power Supply |
| Step 2 | B Check Ground Circuit |
| Step 3 | C Check Imput Signal Circuit ** |
| Step 4 | ---- |
| Step 5 | Check Component *** Info found other areas of SM |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #24 - MASS AIR FLOW SENSOR CHART (DTC NO. 12)
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | Specific symptom depend upon individual incident |
| Step 1 | A Check Power Supply |
| Step 2 | B Check Ground Circuit |
| Step 3 | C Check Imput Signal Circuit ** |
| Step 4 | n/a |
| Step 5 | Check Component *** Info found other areas of SM |
| **= Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #25 - ENGINE COOLANT TEMP SENSOR CHART (DTC NO. 13)
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | Specific symptom depend upon individual incident |
| Step 1 | A Check Power Supply ** |
| Step 2 | B Check Ground Circuit |
| Step 3 | n/a |
| Step 4 | Check Component *** Info found other areas of SM |
| ** =Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #26 - VEHICLE SPEED SENSOR CHART (DTC NO. 14)
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | Specific symptom depend upon individual incident |
| Step 1 | A Check Power Supply ** |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #27 - IGNITION SIGNAL CHART (DTC NO. 21)
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | Specific symptom depend upon individual incident |
| Step 1 | A Check Power Supply |
| Step 2 | B Check Power Supply II |
| Step 3 | C Check Power Supply III |
| Step 4 | D Check Output Signal Circuit I |
| Step 5 | E Check Ground Circuit |
| Step 6 | F Check Harness Continuity |
| Step 7 | G Check Output Signal Circuit II |
| Step 8 | H Check Harness Continuity |
| Step 9 | n/a |
| Step 10 | Check Component *** Info found other areas of SM |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #28 - ECM (ECCS CONTROL MODULE) CHART (DTC NO. 31)
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | Specific symptom depend upon individual incident |
| Step 1 | Code 31 Displayed, Replace ECM ** |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #29 - EGR FUNCTION CHART (DTC NO. 32)
| Step | Procedure |
| NMC Related Symptom(s) | Specific symptom depend upon individual incident |
| Step 1 | A Check Component ** |
| Step 2 | B Perform Road Test |
| Step 3 | C Check Vacuum Source to EGR |
| Step 4 | D Check Control Function |
| Step 5 | E Check Vacuum Hose |
| Step 6 | F Check Power Supply |
| Step 7 | G Check Output Signal Test |
| Step 8 | n/a |
| Step 9 | Check Component *** Info found other areas of SM |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #30 - HEATED OXYGEN SENSOR CHART (DTC NO. 33)
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | Specific symptom depend upon individual incident |
| Step 1 | A Check Component ** |
| Step 2 | B Mixture Ratio Test ** |
| Step 3 | C Check Power Supply |
| Step 4 | D Check Ground Circuit |
| Step 5 | E Check Imput Signal Circuit |
| Step 6 | n/a |
| Step 7 | Check Component *** Info found other areas of SM |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #31 - KNOCK SENSOR CHART (DTC NO. 34)
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | Specific symptom depend upon individual incident |
| Step 1 | A Check Imput Signal Circuit |
| Step 2 | n/a |
| Step 3 | Check Component *** Info found other areas of SM |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #32 - EGR TEMPERATURE SENSOR CHART (DTC NO. 35)
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | Specific symptom depend upon individual incident |
| Step 1 | A Check Power Supply ** |
| Step 2 | B Check Ground Circuit |
| Step 3 | n/a |
| Step 4 | Check Component *** Info found other areas of SM |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #33 - THROTTLE POSITION SENSOR CHART (DTC NO. 43)
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | Specific symptom depend upon individual incident |
| Step 1 | A Check Imput Signal Circuit ** |
| Step 2 | B Check Power Supply |
| Step 3 | C Check Ground Circuit |
| Step 4 | n/a |
| Step 5 | Check Component *** Info found other areas of SM |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #34 - INJECTOR LEAK CHART (DTC NO. 45)
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | IW Failed EPA short test (IC/CO) |
| Step 1 | A Inspect Spark Plugs |
| Step 2 | B Data Monitor Main Signals *** ** |
| Step 3 | C Clear Self Learning ** |
| Step 4 | D Perform Road Test |
| Step 5 | E Verify Repair |
| Step 6 | n/a |
| Step 7 | Check Component *** Info found other areas of SM |
| **= Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #35 - INJECTOR CIRCUIT CHART (DTC NO. 51)
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | IC, IF, III Rough idle, Engine Stall, Hesitation |
| Step 1 | A Check Power Supply |
| Step 2 | B CONSULT Sub Mode Pulse Width Low Level *** ** |
| Step 3 | C Check Output Signal Circuit Injector Resistance |
| Step 4 | n/a |
| Step 5 | Check Component *** Info found other areas of SM |
| **= Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #36 - A/T CONTROL CHART (DTC NO. 54)
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | Specific symptom depend upon individual incident |
| Step 1 | A Check Imput Signal Circuit |
| **= Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #37 - CLOSED THROTTLE POSITION SWITCH CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | Specific symptom depend upon individual incident |
| Step 1 | A Check Overall Function ** |
| Step 2 | B Check Power Supply |
| Step 3 | C Check Ground Circuit |
| Step 4 | n/a |
| Step 5 | Check Component *** Info found other areas of SM |
| **= Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #38 - START SIGNAL CHART (Not self-diagnostic item)
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | IA, IB Hard/No Start |
| Step 1 | A Check Overall Function ** |
| Step 2 | B Check Imput Signal Circuit |
| **= Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #39 - POWER STEERING OIL PRESSURE SWITCH CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | Specific symptom depend upon individual incident |
| Step 1 | A Check Overall Function ** |
| Step 2 | B Check Ground Circuit |
| Step 3 | C Check Imput Signal Circuit |
| Step 4 | n/a |
| Step 5 | Check Component *** Info found other areas of SM |
| **= Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #40 - NEUTRAL POSITION SWITCH & A/T CPU CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | Specific symptom depend upon individual incident |
| Step 1 | A Check Overall Function (ECM) ** |
| Step 2 | B Check Ground Circuit |
| Step 3 | C Check Imput Signal Circuit |
| Step 4 | D Check Overall Function (ATCU) ** |
| Step 5 | E Check Imput Signal Circuit |
| Step 6 | n/a |
| Step 7 | Check Component *** Info found other areas of SM |
| **= Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #41 - FUEL PUMP CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | Specific symptom depend upon individual incident |
| Step 1 | A Check Overall Function |
| Step 2 | B Check Component (Fuel Pump Relay) *** ** |
| Step 3 | C Check Power Supply |
| Step 4 | D Check Ground Circuit |
| Step 5 | E Check Output Signal Circuit |
| Step 6 | n/a |
| Step 7 | Check Component *** Info found other areas of SM |
| **= Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #42 - IACV-AAC VALVE CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | Specific symptom depend upon individual incident |
| Step 1 | A Check Overall Function |
| Step 2 | B Check Power Supply |
| Step 3 | C Check Output Signal Circuit ** |
| Step 4 | n/a |
| Step 5 | Check Component *** Info found other areas of SM |
| **= Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #43 - POWER VALVE CONTROL CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | Specific symptom depend upon individual incident |
| Step 1 | A Check Overall Function ** |
| Step 2 | B Check Vacuum Source to Power Valve Actuator |
| Step 3 | C Check Control Function |
| Step 4 | D Check Power Supply |
| Step 5 | E Check Output Signal Circuit |
| Step 6 | n/a |
| Step 7 | Check Component *** Info found other areas of SM |
| **= Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #44 - VTC SOLENOID VALVE CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | Specific symptom depend upon individual incident |
| Step 1 | A Check Component *** ** |
| Step 2 | B Check Control Function |
| Step 3 | C Check Power Supply |
| Step 4 | D Check Imput Signal Circuit |
| Step 5 | E Check VTC Solenoid Valve Operation |
| ** = Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |
DIAGNOSTIC PROCEDURE #45 - COOLING FAN CONTROL CHART
| Step | Procedure |
|---|---|
| NMC Related Symptom(s) | Specific symptom depend upon individual incident |
| Step 1 | A Check Cooling Fan Low Speed Operation |
| Step 2 | B Check Cooling Fan High Speed Operation |
| Step 3 | C Check Component *** ** |
| Step 4 | D Check Power Supply |
| Step 5 | E Check Ground Circuit |
| Step 6 | F Check Output Signal Circuit |
| Step 7 | G Check Power Supply |
| Step 8 | H & I Check Ground Circuit and Harness Continuity |
| Step 9 | J Check Output Signal Circuit |
| Step 10 | K Check Component *** ** |
| **= Test is Conducted Using CONSULT | |
| *** = Additional Diagnostic Procedure Inserted | |