LEMON Manuals: Even more car manuals for everyone
Home >> Mitsubishi >> 2014 >> Mirage ES, Standard Trans >> Repair and Diagnosis >> Quick Lookups >> Technical Bulletins >> Campaigns >> Other Variant >> Engine Control Systems >> ECM Reprogramming For Engine Knocking Noise - Service Campaign - Revision (SC-16-001REV2)

ECM Reprogramming For Engine Knocking Noise - Service Campaign - Revision (SC-16-001REV2)

WARNING: This page is about the Mirage DE, Automatic CVT Trans, which is a different variant/trim than selected.
Publication date: 2020-11-01
Reference number: SC-16-001REV2
Supersedes refnos: SC-16-001, SC-16-001REV

ECM REPROGRAMMING FOR ENGINE KNOCKING NOISE - SERVICE CAMPAIGN - REVISION

ECM REPROGRAMMING FOR ENGINE KNOCKING NOISE - SERVICE CAMPAIGN - REVISION

SERVICE CAMPAIGN BULLETIN

Reference Number(s): SC-16-001REV2, Date of Issue:  November 01, 2020
MITSUBISHI: 2014-15 Mirage
Superceded Bulletin(s): SC-16-001REV, Date of Issue:  March 01, 2016

REVISION HISTORY

This bulletin supersedes SC-16-001REV, issued March 2016, to add instructions on submitting a duplicate claim. Revisions are italicized and indicated by . 

PURPOSE

During cold start, the engine ECU may order inappropriate fuel amounts which may cause engine noise.

This campaign bulletin instructs dealers to reprogram the ECM with new software on all affected vehicles. In rare cases, if the vehicle exhibits an engine knocking noise, the engine may need to be replaced.

In the rare occasion that the engine does require replacement, dealers should do the following:

AFFECTED VEHICLES

Certain 2014 - 2015 Mirage vehicles built before  February 18, 2015

IMPORTANT: To maximize customer satisfaction with the quality of their vehicle, affected new or used inventory vehicles should be remedied before the vehicle is delivered. Dealers must check their inventory vehicles' VINs on the Warranty Superscreen to verify whether the vehicle is involved in this service campaign.

CUSTOMER NOTIFICATIONS

A letter will be sent to all owners of affected vehicles requesting they schedule an appointment with their local Mitsubishi dealer to have their vehicle remedied. A sample copy of the customer notification letter is attached to the end of this bulletin.

REQUIRED OPERATIONS

Before starting this campaign procedure, CHECK THE WARRANTY SUPERSCREEN  to verify if the vehicle is an affected VIN for this campaign and this campaign procedure has not already been completed.

  1. Confirm your MUT-III is updated with the latest reprogramming database.
  2. Reprogram the ECM with the new software. Refer to the ECM Reprogramming Chart for new software information.
  3. Confirm if engine requires replacement (only if knocking noise is present and verified).
    IMPORTANT: If an affected vehicle has a Malfunction Indicator Lamp (MIL) illuminated before reprogramming  , and DTCs are listed in the ECM memory, diagnose and repair those DTCs per the service manual before  reprogramming. DO NOT  reprogram the ECM until the reason(s) for other DTCs being set is corrected.

EQUIPMENT

The following equipment is needed to reprogram the ECM. 

ECM REPROGRAMMING CHART

NOTE: The following information is for reference only.
Model Engine ECU Part Number D/B Number Software Part Number
Previous New
2014-2015 Mirage 3A92 5MT 1860C141 1862C360 1860C14101
1860C14100
1860C14102
3A92 CVT 1860C142 1862C361 1860C14202
1860C14201
1860C14200
1860C14203

REPAIR PROCEDURE

A. Confirm latest database in MUT-III

CAUTION: Any damage incurred, if an error is made during this procedure, may not be warrantable.
NOTE: Reprogramming the ECM with the latest database (e.g., N15112) includes all past and current reprogramming for TSBs of affected vehicles. It is not necessary to reprogram the ECM for each previous TSB.
  1. Check the underside of the hood to verify there is no "Authorized Modification" label (see step  19 in the Reprogramming Procedure for example) previously installed to indicate this reprogramming has already been completed. If a label is present and the "ROM ID #" on the label matches the "New S/W Part No." in the table above, the ECM is at the latest level and reprogramming is not necessary. Conduct normal diagnosis for the described condition.

    For MEDIC 3/4 users only: (MUT-III users go to step   5 ) 

  2. Verify the MEDIC 3/4 is at version 3.5 and at update 363  or higher.

    If your MEDIC 3/4 update is at least 363  , continue with the REPROGRAMMING PROCEDURE .

    If your MEDIC 3/4 update is below 363  , update your MEDIC as follows.

    G13343124
  3. Select the MEDIC 3/4 Admin tab and click on "Updates."
    G13343125
  4. IF the MEDIC update screen advises updates are available, click the "Begin" button. After all updates are complete, GO TO THE  REPROGRAMMING PROCEDURE  . 
    G13343126
  5. STANDALONE MUT-III SCAN TOOL VIEWER (STV) ONLY: (MEDIC 3 USERS GO TO THE  REPROGRAMMING PROCEDURE  )  . Verify that your MUT-III has the most current version of the reprogramming database: From the MUT-III Main Page:
    • Select "Special Function"
    • Select "ECU Reprogramming"
    • Select "Database File Display-CAN"
    • Confirm the database number displayed at the top right of the chart is N15112 or higher 
      • If the database number displayed on your MUT-III is N15112 or greater, continue to the REPROGRAMMING PROCEDURE .
      • If the reprogramming database number displayed on your MUT-III is lower than N15112, locate the reprogramming CD containing database N15112 and follow the instructions provided with the CD to update your MUT-III.
    G13343127

B. Reprogramming Procedure

CAUTION: CONNECT A BATTERY CHARGER TO THE VEHICLE'S BATTERY DURING THE REPROGRAMMING PROCEDURE. DO NOT ALLOW THE BATTERY CHARGER TO TIME OUT. BATTERY VOLTAGE (AS MEASURED AT THE BATTERY POSTS WITHOUT ELECTRICAL LOAD) MUST BE KEPT AT 12.4V OR HIGHER IN ORDER TO REPROGRAM THE ECM. MEASURE THE BATTERY VOLTAGE AND CHARGE AS NECESSARY.
NOTE: VCI Stand-alone reprogramming is not available for this procedure. The laptop and the VCI must remain connected for the entire procedure.
  1. Connect the equipment as follows:
    • Turn the MEDIC PC/tablet on. If the battery indicator in the lower right hand corner of the screen does not show a full charge, it is recommended that either the battery be charged prior to beginning, or be used with the A/C power adaptor connected.
    • Connect the USB cable to the VCI/VCI Lite.
    • When the laptop/tablet displays the MUT-III main screen, connect the USB cable to the device.
    • Connect the MUT-III main harness with the blue DLC connection to the VCI/VCI Lite.
    • Connect the blue connection of the MUT-III main harness to the vehicle's data link connector.
    • Turn the VCI power switch ON. Verify that the indicator lamp in the upper right corner of the screen is green.
      NOTE: VCI and MEDIC 3.5 Laptop shown for illustration purposes only.
    G13343128
    CAUTION: DO NOT DISTURB THE HARNESS CABLES OR CONNECTIONS DURING THE REPROGRAMMING PROCESS AS IT COULD CAUSE THE CONTROL UNIT TO LOSE DATA OR PREVENT FUTURE REPROGRAMMING. IF THE USB CABLE IS DISCONNECTED DURING THIS PROCEDURE, A WARNING MESSAGE WILL DISPLAY.
  2. Turn the ignition switch to the "ON" position.
    • If the vehicle is equipped with the F.A.S.T. System, the transmitter must remain in the vehicle for the entire procedure.
    • For vehicles equipped with OSS, press the START/STOP button twice without applying the brake. The LED in the button should be green.
  3. If using MEDIC, from the main page, click the MUTIII STV icon at the top center of the screen to open MUT-III.
    G13343129
  4. Go to the MUT-III home screen and click on "Special function."
    G13343130
  5. Select "ECU reprogramming."
    G13343131
  6. In ECU reprogramming, select "Automatic Reprogramming (CAN)."
    G13343132
  7. Press the model information display button (car icon) and verify that all vehicle information is correct.
    • If vehicle information is NOT correct, follow steps a - e below.
    • If vehicle information is correct, click the check mark at the bottom of the page, then go to step 8.
    G13343133
    1. If the VIN or vehicle description displayed does not match the vehicle you are working on, click the eraser icon at the bottom of the page to erase vehicle data.

      Then click the "VIN" button.

      G13343134
    2. Click the icon in the lower RH corner of the screen to have MUT-III automatically read the VIN.

      If a message appears saying the VIN cannot be input automatically, manually enter the 17 digit VIN into the VIN field at the top of the page.

      Make sure the VIN is correct and click the check mark.

      G13343135
    3. Click the CLASS button.
      G13343136
    4. Look at the label on the passenger side B-pillar to identify the appropriate class. Select it and click the check mark at the bottom of the page.
      G13343137
    5. Confirm all data matches the vehicle, then click the check mark at the bottom of the page.
      IMPORTANT: If an affected vehicle has a Malfunction Indicator Lamp (MIL) illuminated before reprogramming, and DTCs are listed in ECM memory, diagnose and repair those DTCs per the applicable service manual before reprogramming. DO NOT reprogram the ECM until the reason(s) for other DTCs being set is corrected.
      G13343138
  8. "MFI" should be highlighted by default. If not, click on it to highlight it. Click the check mark  to continue.
    G13343139
    NOTE: In the next step, if the "pop-up" box does not appear, change Tab to TIR then back to MUT-III (the pop-up box should then appear).
  9. A message will advise the system will "Automatic search the data."

    Click the check mark to continue.

    G13343140
    G13343141

    IF ECU IS ALREADY AT LATEST VERSION 

    G13343142

    If the message seen at left is displayed, the ECU software is already at the most current level. Do not continue with the REPROGRAMMING PROCEDURE . This TSB does not  apply.

    Click the check mark to clear the window, then click the Home icon at the lower left corner of the screen to return to the System Select main page.

    Turn the ignition switch to the OFF position and disconnect the MUT-III. Turn off and disconnect the battery charger. Conduct normal diagnosis per the service manual.

    If a "Complete Reprogramming" message does not  appear, continue with the reprogramming procedure.

  10. The Automatic Reprogramming (CAN) database screen will display.
    • Verify that the new ECU and S/W part numbers are listed in the table.
    • Confirm the database number at the top right of the table is N15112 or higher.
    • If more than one row is displayed in the table, refer to the ECM Reprogramming Chart on page 2 to highlight and select the correct row.
    • Click the check mark to continue.
    G13343143
  11. The "Check reprogramming data" window should appear with the new file name.
    NOTE: Refer to the ECM Reprogramming Chart on page 2 for the new file names.
  12. Click on the check mark in the pop-up box to initiate the reprogramming.
    G13343144
  13. Once the reprogramming is initiated, the screen as shown will indicate the reprogramming progress.
    NOTE: Do not disturb the cables or turn off the ignition during reprogramming.
    G13343145
  14. Reprogramming is completed.
    1. Verify that the S/W Part No. Is correct.
    2. Click on the check mark.
    3. Turn OFF ignition switch for at least 8 seconds.
    4. Turn ignition switch ON, then proceed to the next step.
    G13343146
  15. Click on the "home" button.
    G13343147
  16. Perform an "Erase and Read all DTCs."
    1. Select "Special function."
      G13343148
    2. Select "All DTCs."
      G13343149
    3. Select "Erase and Read All DTCs."
      G13343150
    4. The "System List" on the left side of the screen will have all selections checked. Do not change these selections. DTCs may be set if the vehicle is equipped with options that are unchecked.
    5. Click the check mark to continue.
      G13343151
      NOTE: If, in some cases, the check mark button at the bottom is not active, perform the following:
      1. Select the System name that is underlined (for example, TPMS, as shown on left).
      2. Select the appropriate option for the vehicle. Repeat steps  1 and 2 for all underlined systems.
      3. Click on the check mark. Wait until MUT-III is finished and click the check mark again to confirm.
      G13343152
    6. A window will pop up asking you to confirm DTC erasing. Click the check mark for DTC erasing and reading to begin.
  17. When DTC erasing is completed, click the check mark in the pop-up message that reads "All erasing and checks are completed."
    1. If DTCs return after reprogramming, click the check mark to clear the window. Diagnose and repair per the Service Manual.
    2. If DTCs do not return, click the check mark to clear the window, then click the home icon at the lower left of the screen to return to the main menu.
    G13343153
  18. Turn off the ignition switch and disconnect the MUT-III. Turn off and disconnect the battery charger.
  19. Using a ball-point pen, enter the appropriate ECU part number, Software Part Number (ROM ID#), this Technical Service Bulletin number, your dealer code, and the current date on the Engine Compartment/Control Module Label (p/n MSSF024G00). The Vendor Code is not applicable. The label is available from your facing PDC.
    G13343154
    NOTE: The Control Module Label is NOT used for this reflash. It should be discarded.
  20. Carefully remove all dirt and oil from a vacant area near the VECI label on the underside of the hood and affix the Engine Compartment Label (LH side, above) to that area.
  21. Test drive the vehicle to confirm proper operation. Diagnose and correct any DTCs that return.
  22. Does the vehicle exhibit the engine knocking noise condition?
    • YES  - Go to ENGINE REPLACEMENT VERIFICATION PROCEDURES.
    • NO  - Repair is complete. Return vehicle to customer.
  23. Engine Replacement Verification Procedure (only if engine knocking noise is reported) 
    1. Start the engine and let idle.
      • If no knocking noise is heard, go to step 2.
      • If a knocking noise is heard, go to step  3.
    2. Put selector lever in D position, apply the emergency brake and service brake and gradually raise engine speed to 1, 500 RPM.
      • If a knocking noise is heard, go to step 3.
      • If the engine noise is normal, do NOT  replace the engine. Return vehicle to customer.
    3. Create a Techline case.
  24. Open the hood and keep the engine running at idle. If noise is only heard at 1, 500 RPM, have a second person in drivers seat and gradually increase engine speed to 1, 500 RPM during the recording.
  25. Using a video recording device (smart-phone, camera, etc.) start the video recording by clearly filming the VIN on the FMVSS Label on the B-Pillar. Then stand near the open hood and record the knocking noise for approximately 5 seconds.
    NOTE: To keep file size more manageable, total filming time should be less than 10 seconds. File size may be reduced by adjusting video recording resolution to a lower setting or by using a video compression software on your PC (such as Microsoft Movie Maker, Wondershare Video Converter etc).
    1. 6. Save the video recording with the following naming convention: the last 8 digits of the VIN AND the Techline case number (for example: EH004169_187621.mp4). 
    2. 7. Attach the video file to the Techline case using the instructions and images below.
      1. Download the video file to the device you will be accessing the Techline System from:
        • From MEDIC: Copy the video file to a flash drive and connect to the USB port of the Toughbook/Toughpad.
        • From any device other than MEDIC: Copy the video file to the hard drive of the PC (or a flash drive may be used if desired).
      2. Navigate to the Techline System (through MDL). Find and open the previously created Techline case.
        G13343155
        G13343156

        Click on the attachment icon (paper clip).

        NOTE: This icon is only available when a Techline case is NOT closed AND the video file size limit for attachments is 25 MB.
      3. A pop-up window will open. Click on Browse to find the file you want to attach.
      4. Navigate to the location of the video file, select it, and click "Open".
        • On MEDIC: Navigate to the flash drive.
        • On another device (other than MEDIC): Locate the file on the hard drive (or flash drive).
      5. The chosen file path will be displayed, as shown. Click the "Upload" to attach the file to the Techline case.
      6. The file will be shown as attached. Click on "Close" to go back to the Techline case.
      7. From the Techline case, click on "Save" to save the attachment to the case. Verify the file is showing in the attachment section at the bottom of the Techline case.
      G13343157
      G13343158
    3. 8. Contact Techline for assistance (1-800-446-6064).
    4. 9. Order the new engine assembly (209 restriction applies, must be released by MMNA).

PARTS INFORMATION

Use the genuine Mitsubishi Parts listed below:

Description Part Number Quantity
Label, Engine Compartment MSSF024G00 1

Only replace the Engine Assembly if engine noise is verified, and all instructions in the ENGINE REPLACEMENT VERIFICATION PROCEDURE, in this bulletin, have been completed. 

Description Part Number Quantity
Engine Assy, Long 1000C848 1

WARRANTY INFORMATION

There are 3 repair scenarios for this campaign number. 

Scenario # Campaign Op # Labor Time Repair Description Part Number
1 C1602A01 .4 hours Re-flash the ECU MSSF024G00 (label)
2 C1602A02 8.3 hours Re-flash the ECU and check engine for noise per TSB - Replace if needed MULTIPLE
3 C1602A03 7.9 hours Check engine for noise per TSB - Replace if needed (Re-flash already completed)  MULTIPLE 

WARRANTY/RECALL CAMPAIGN CLAIM INFORMATION

Enter all claims as claim type "C" - Recall/Campaign Claims. 

Please follow the campaign instructions when entering each claim in order to select the applicable operation code that correctly matches up with the work that was actually performed. A claim example is provided below.

Certain 2014-2015 MY Mirage models:

Required Operation to be performed Labor Operation Labor Time
1 2014-15 MY Mirage - Re-flash ECU only C1602A01 0.4 hrs
2 2014-15 MY Mirage - Re-flash ECU & Replace Engine C1602A02 8.3 hrs
3 2014-15 MY Mirage - Replace Engine C1602A03  7.9 hrs 

Claim Header Section: 

G13343159

After entering the required customer data, vehicle information, selecting the applicable repair campaign and scenario performed (please note there are 2 possible repair scenarios for this campaign), and then hitting the "Save and Continue"  button, the system will automatically fill-in several fields. See the Labor and Parts examples below.

LABOR AND PARTS

Labor: 

There are 2 possible repair scenarios for this campaign: Inspect Only and Inspect and Replace Engine. This campaign requires reprogramming the ECU then, in rare cases, if the engine is making noise (as per the TSB), replace the engine. 

Scenario 1

G13343160

Scenario 2

G13343161

Parts: 

  1. Re-flash the ECU: Only the engine compartment flash label (#MSSF024G00).
  2. Re-flash and Replace Engine Assembly: Use only engine "long block" part #1000C848 and other parts as needed along with engine compartment label (MSSF024G00).

RENTAL CARS AND RETURN FREIGHT COSTS

If there is a need to provide the owner with a rental car or return freight charges, claim the applicable charges in this section of the claim on the lower portion of the labor entry screen.

G13343162

REPLACED PARTS RETENTION AND RETURN OF REPLACED ENGINE ASSEMBLY

Retain all replaced parts for the normal retention period and return parts if requested by a warranty parts return letter.

G13116516