LEMON Manuals: Even more car manuals for everyone
Home >> Mitsubishi >> 2010 >> Lancer ES, Automatic CVT >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 24 (Combination Meter - Lancer SPORTBACK) >> On-Vehicle Service >> Speedometer Check

Speedometer Check

WARNING: This page is about a different variant/trim than selected.
CAUTION:
  • Since the diagnostic trouble code may be stored in the ASC-ECU when checking the speedometer with speedometer tester, erase the diagnostic trouble code.
  • Do not accelerate or decelerate suddenly during servicing work.
  1. Adjust the pressure of tires to the specified level (Refer to ON-VEHICLE SERVICE ).
  2. Where applicable, ensure that the TPMS warning light is not illuminating or flashing.
  3. Press the ASC OFF switch for 3 seconds or more to stop the ASC operation.
  4. Set the vehicle onto a speedometer tester and use wheel chocks to hold the rear wheels. <FWD>
    Fig 1: Setting Vehicle Onto Speedometer Tester - FWD
    G05906324Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  5. Set the vehicle on the speedometer tester. Set the rear wheel on the free roller, and set to the FWD state. <AWD>
    Fig 2: Setting Vehicle Onto Speedometer Tester - AWD
    G05906325Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  6. For prevention of vehicle from starting out, install extension fittings on front and rear towing hook or tie down hook, and install both ends to the anchor plate.
  7. Check if the speedometer indicator range is within the standard values.
    Fig 3: Identifying Tension Bar And Anchor Plate
    G05385252Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

    Standard value <Except vehicles for CANADA>: 

    SPEEDOMETER INDICATOR RANGE VALUE (EXCEPT VEHICLES FOR CANADA)

    Standard indication {mph (km/h)} Allowance range {mph (km/h)}
    10 (16) 8.5 - 11.5 (13.6 - 18.4)
    25 (40) 23.5 - 26.5 (37.6 - 42.4)
    50 (80) 48.5 - 51.5 (77.6 - 82.4)
    75 (120) 73.5 - 76.5 (117.6 - 122.4)
    100 (161) 98.5 - 102.5 (158.6 - 165.0)
    125 (201) 123.5 - 127.5 (198.6 - 205.0)
    150 (241) 148.5 - 153.5 (239.0 - 247.0)
    Fig 4: Identifying Tension Bar And Anchor Plate
    G06474165Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

    Standard value <Vehicles for CANADA>: 

    SPEEDOMETER INDICATOR RANGE VALUE (VEHICLES FOR CANADA)

    standard indication {km/h (mph)} Allowance range {km/h (mph)}
    20 (12.4) 19 - 24 (11.8 - 14.9)
    40 (24.8) 40 - 44 (24.8 - 27.3)
    80 (49.7) 80 - 85 (49.7 - 52.8)
    120 (74.6) 120.5 - 125.5 (74.9 - 78.0)
    160 (99.4) 160.5 - 165.5 (99.7 - 102.8)
    200 (124.3) 200.5 - 207.0 (124.6 - 128.6)
    240 (149.1) 240.5 - 247.0 (149.4 - 153.5)
  8. If not within the standard value, check the tire size. If an incorrect size of tire is used, replace it and check again. If the tire size is correct, a defect may be present in components and circuit between the ASC or engine control module and the combination meter. Check the following items.