LEMON Manuals: Even more car manuals for everyone
Home >> Mitsubishi >> 2006 >> Raider XLS, RWD >> Repair and Diagnosis >> Steering >> Power Steering >> Column >> Diagnosis And Testing >> Installation

Diagnosis And Testing: Installation

WARNING: BEFORE SERVICING THE STEERING COLUMN THE AIRBAG SYSTEM MUST BE DISARMED. REFER TO SUPPLEMENTAL RESTRAINT SYSTEM (SRS) FOR SERVICE PROCEDURES. FAILURE TO DO SO MAY RESULT IN ACCIDENTAL DEPLOYMENT OF THE AIRBAG AND POSSIBLE PERSONAL INJURY.
CAUTION: All fasteners must be torqued to specification to ensure proper operation of the steering column.
Fig 1: Positioning Steering Column On Dash Panel Support
G04286316Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  1. Position the steering column (3) on the dash panel support (1) and loosely install the mounting nuts (4).
  2. Firmly slide the steering column upward against the studs (2) in dash panel and hand tighten the nuts.
  3. Center steering column (3) in dash opening and tighten mounting nuts (4) to 28 N.m (250 in. lbs.).
    NOTE: Torque the upper left nut first then the lower right nut. Then torque the lower left nut then the upper right nut.
    Fig 2: Installing Steering Shaft Coupler On Steering Shaft
    G04286317Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  4. Install the steering shaft coupler (7) on the steering shaft (1) and loosely install a new bolt (2).
    NOTE: A new bolt must be used for reinstallation.
  5. Tighten the coupler bolt (2) to 57 N.m (42 ft. lbs.).
    Fig 3: Installing Brake Light Switch
    G04286318Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  6. Install a new brake light switch (Refer to REMOVAL ).
  7. Install the shifter cable (2). (Refer to INSTALLATION ).
    Fig 4: Connecting Wiring Harness To Column
    G04286319Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  8. Connect the wiring harness (1,2 and 3) to the column.
  9. Install the SKIM module.
  10. Install the clockspring (Refer to INSTALLATION ).
    Fig 5: Installing Shrouds
    G04286320Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  11. Install the shrouds (1 and 2).
    Fig 6: Installing Steering Column Opening Cover Reinforcement
    G04286321Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  12. Install the steering column opening cover reinforcement (2) (Refer to INSTALLATION ).
    Fig 7: Installing Steering Column Opening Cover
    G04286322Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  13. Install the steering column opening cover (3).
    Fig 8: Installing Steering Wheel
    G04286323Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  14. Align the spline on the wheel hub to shaft.
  15. Then install the steering wheel (3) and install a new bolt (4). Tighten the bolt to 61 N.m (45 ft. lbs.).
    Fig 9: Installing Airbag
    G04286324Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  16. Reconnect the electrical connectors (2) for the air bag (3).
  17. Install the airbag (3) (Refer to INSTALLATION ).
    Fig 10: Installing Tilt Lever Handle
    G04286325Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  18. Install the tilt lever handle (5).
  19. Install the negative battery terminal.
  20. Test the operation of the horn, Electronic PRNDL Indicator, lights and any other functions that are steering column operated.