LEMON Manuals: Even more car manuals for everyone
Home >> Mitsubishi >> 2006 >> Raider XLS, RWD >> Repair and Diagnosis >> Engine Performance >> System >> Electrical Diagnostics (2 Of 5) >> DTC P0151: O2 Sensor 2/1 Circuit Low >> Diagnostic Test

Diagnostic Test

  1. O2 SENSOR BELOW 2.52 VOLTS 
    1. Start the engine.
    2. Allow the engine to reach normal operating temperature.
    3. With a scan tool, read the 2/1 O2 Sensor voltage.

    Q: Is the voltage below 2.52 volts? 

    Yes  :

    • Go To 2

    No  :

  2. (K43) O2 2/1 SIGNAL CIRCUIT 
    1. Turn the ignition off.
    2. Disconnect the 2/1 O2 Sensor harness connector.
    3. Ignition on, engine not running.
    4. With a scan tool, monitor the 2/1 O2 Sensor voltage.

    Q: Is the O2 Sensor voltage above 4.8 volts? 

    Yes  :

    • Go To 3

    No  :

    • Go To  5
  3. O2 SENSOR 
    Fig 1: Identifying O2 Sensor
    G04282824Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    1. Measure the voltage on the (K902) O2 Return Upstream circuit in the O2 Sensor harness connector.

    Q: Is the voltage at 2.5 volts? 

    Yes  :

    No  :

    • Go To 4
  4. (K902) O2 RETURN UPSTREAM CIRCUIT SHORTED TO GROUND 
    Fig 2: O2 Return Upstream Circuit Shorted To Ground
    G04282825Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    1. Turn the ignition off.
    2. Disconnect the C1 PCM harness connector.
    3. Measure the resistance between ground and the (K902) O2 Return Upstream circuit in the O2 Sensor harness connector.

    Q: Is the resistance below 100 ohms? 

    Yes  :

    No  :

    • Go To  8
  5. (K43) O2 2/1 SIGNAL CIRCUIT SHORTED TO GROUND 
    Fig 3: O2 2/1 Signal Circuit Shorted To Ground
    G04282826Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    1. Turn the ignition off.
    2. Disconnect the C1 and C2 PCM harness connectors.
    3. Measure the resistance between ground and the (K43) O2 2/1 Signal circuit in the O2 Sensor harness connector.

    Q: Is the resistance below 100 ohms? 

    Yes  :

    No  :

    • Go To 6
  6. (K43) O2 2/1 SIGNAL CIRCUIT SHORTED TO (K902) O2 RETURN UPSTREAM CIRCUIT 
    Fig 4: O2 2/1 Signal Circuit Shorted To (K902) O2 Return Upstream Circuit
    G04282827Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    1. Measure the resistance between the (K43) O2 2/1 Signal circuit and the (K902) O2 Return Upstream circuit in the O2 Sensor harness connector.

    Q: Is the resistance below 100 ohms? 

    Yes  :

    • Repair the short between the (K902) O2 Return Upstream circuit and the (K43) O2 2/1 Signal circuit.
    • Perform POWERTRAIN VERIFICATION TEST .

    No  :

    • Go To 7
  7. (K43) O2 2/1 SIGNAL CIRCUIT SHORTED TO THE (Z934) HEATER GROUND CIRCUIT 
    Fig 5: O2 2/1 Signal Circuit Shorted To (Z934) Heater Ground Circuit
    G04282828Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    1. Measure the resistance between the (K43) O2 2/1 Signal circuit and the (Z934) O2 Heater ground circuit in the O2 Sensor harness connector.

    Q: Is the resistance below 100 ohms? 

    Yes  :

    No  :

    • Go To 8
  8. PCM 
    NOTE: Before continuing, check the PCM harness connector terminals for corrosion, damage, or terminal push out. Repair as necessary.
    1. Using the schematics as a guide, inspect the wire harness and connectors. Pay particular attention to all Power and Ground circuits.

    Q: Were there any problems found? 

    Yes  :

    No  :