DTC C1340: Stoplight Switch: Diagnosis
Required Special Tools:
- MB991958: Scan Tool (M.U.T.-III Sub Assembly)
- MB991824: Vehicle Communication Interface (V. C. I.)
- MB991827: M.U.T.-III USB Cable
- MB991910: M.U.T.-III Main Harness A
- MB991997: ASC Check Harness
- STEP 1. Using scan tool MB991958, diagnose the CAN bus line. CAUTION: To prevent damage to scan tool MB991958, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool MB991958.
- Connect scan tool MB991958 to the data link connector.
- Turn the ignition switch to the "ON" position.
- Diagnose the CAN bus line.
- Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the CAN bus line found to be normal?
YES : Go to Step 3.
NO : Repair the CAN bus line. Then go to Step 2.
- STEP 2. Recheck for diagnostic trouble code. CAUTION: To prevent damage to scan tool MB991958, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool MB991958.
- Turn the ignition switch to the "ON" position.
- Erase the DTC.
- Turn the ignition switch to the "LOCK" (OFF) position.
- Turn the ignition switch to the "ON" position.
- Check if the DTC is set.
- Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is DTC C1340 set?
YES : Go to Step 3.
NO : The procedure is complete.
- STEP 3. Check the stoplight operation.
- Turn the ignition switch to the "ON" position.
- Check the operation of the stoplight when the brake pedal is operated.
OK:
Brake pedal depressed: ON
Brake pedal released: OFF
Q: Is the check result normal?
YES : Go to Step 4.
NO : Go to Step 6.
- STEP 4. Connector check: A-03 ABS/TCL-ECU connector, C-28 joint connector (1).
Q: Is the check result normal?
YES : Go to Step 5.
NO : Repair or replace the damaged component(s). Then go to Step 16.
- STEP 5. Measure the resistance at the C-28 joint connector (1).
- Disconnect the connector C-28 joint connector (1) and A-03 ABS/TCL-ECU connector, and measure the wiring harness-side connector. .
- Measure the resistance between the C-28 joint connector (1) terminal 15 and A-03 ABS/TCL-ECU connector terminal 41.
OK: Continuity exists (2 ohms or less)
Q: Is the check result normal?
YES : Go to step 15.
NO : Repair the harness wire. Then go to Step 16.
- STEP 6. Connector check: A-03 ABS/TCL-ECU connector, C-28 joint connector (1), C-103 stoplight switch connector, C-26 intermediate connector, F-02 intermediate connector <ECLIPSE>, F-05 <standard type rear spoler> or F-30 <large type rear spoiler> high-mounted stoplight, F-07 rear combination light (RH), F-14 rear combination light (LH)
Q: Is the check result normal?
YES : Go to step 7. .
NO : Repair or replace the damaged component(s). Then go to step 16.
- STEP 7. Check for stoplight switch installation
Refer to GROUP 35A - On-vehicle Service.
Q: Is the check result normal?
YES : Go to Step 8.
NO : Install the stoplight switch correctly (Refer to GROUP 35A - On-vehicle service). Then go to Step 16.
- STEP 8. Check for stoplight switch
Refer to GROUP 35A - Brake pedal inspection.
Q: Is the check result normal?
YES : Go to step 9.
NO : Replace the stoplight switch (Refer to GROUP 35A - Brake pedal). Then go to step 16.
- STEP 9. Check the fuse No. 11.
Visually check for melted fuse.
Q: Is the check result normal?
YES : Go to Step 13.
NO : Go to Step 10. .
- STEP 10. Measure the resistance at the C-103 stoplight switch connector.
- Disconnect the connector C-103, and measure at the wiring harness-side connector.
- Remove fuse No. 11.
- Measure the resistance between the C-103 stoplight switch connector terminal 2 and body ground.
OK: No continuity
Q: Is the check result normal?
YES : Go to Step 11.
NO : The wiring harness betweem fuse No. 11 and C-103 stoplight switch connector terminal 2 is shorted to ground. Repair the wiring harness. Then, replace fuse No. 11. Then go to Step 16.
- STEP 11. Measure the resistance at the C-103 stoplight switch connector.
- Disconnect the connector C-103, and measure at the wiring harness-side connector.
- Disconnect the connector C-28 joint connector (1).
- Measure the resistance between the C-103 stoplight switch connector terminal 1 and body ground.
OK: No continuity
Q: Is the check result normal?
YES : Go to Step 12.
NO : The wiring harness betweem C-28 joint connector (1) terminal 12 and C-103 stoplight switch connector terminal 1 is shorted to ground. Repair the wiring harness. Then, replace fuse No. 11. Then go to Step 16.
- STEP 12. Measure the resistance at the C-28 joint connector (1).
- Disconnect the connector C-28, and measure at the wiring harness-side connector.
- Disconnect the connector A-03 ABS/TCL-ECU connector.
- Measure the resistance between the C-28 joint connector (1) terminal 15 and body ground..
OK: No continuity
Q: Is the check result normal?
YES : The wiring harness between C-28 joint connector (1) terminal 17 and F-05 <standard type rear spoiler> or F-30 <large type rear spoiler> high-mounted stoplight connector terminal 2 or the wiring harness F-07 rear combination light (RH) connector terminal 2 and F-14 rear combinatonlight (LH) connector terminal 2 is shorted to ground. Repair the wiring harness. Then, replace fuse No. 11. Then go to step 15.
NO The wiring harness between C-28 joint connector (1) terminal 15 and A-03 ABS/TCL-ECU connector terminal 41 is shorted to ground. Repair the wiring harness. Then, replace fuse No. 11. Then go to Step 16.
- STEP 13. Measure the resistance at the C-103 stoplight switch connector.
- Disconnect the connector C-103, and measure at the wiring harness-side connector.
- Remove fuse No. 11.
- Measure the resistance between the C-103 stoplight switch connector terminal 2 and fuse No. 11.
OK: Continuity exists (2 ohms or less)
Q: Is the check result normal?
YES : Go to Step 14.
NO An open circuit is present in the wiring harness between fuse No. 11 and C-103 stoplight switch connector terminal 2. Repair the wiring harness. Then go to Step 16.
- STEP 14. Measure the resistance at the C-103 stoplight switch connector.
- Disconnect the connector C-103, and measure at the wiring harness-side connector.
- Disconnect the connector C-28 joint connector (1).
- Measure the resistance between the C-103 stoplight switch connector terminal 1 and C-28 joint connector (1) terminal 12.
OK: Continuity exists (2 ohms or less)
Q: Is the check result normal?
YES : Go to Step 15.
NO An open circuit is present in the wiring harness between C-28 joint connector (1) terminal 12 and C-103 stoplight switch connector terminal 1. Repair the wiring harness. Then go to Step 16.
- STEP 15. Recheck for diagnostic trouble code.
Check again if the DTC is set.
- Turn the ignition switch to the "ON" position.
- Erase the DTC.
- Turn the ignition switch to the "LOCK" (OFF) position.
- Turn the ignition switch to the "ON" position.
- Check if the DTC is set.
- Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is DTC C1340 set?
YES : Replace the hydraulic unit (integrated with ABS/TCL-ECU). Then go to step 16.
NO It can be assumed that this malfunction is intermittent. Refer to HOW TO USE TROUBLESHOOTING/INSPECTION SERVICE POINTS
- STEP 16. Recheck for diagnostic trouble code.
Check again if the DTC is set.
- Turn the ignition switch to the "ON" position.
- Erase the DTC.
- Turn the ignition switch to the "LOCK" (OFF) position.
- Turn the ignition switch to the "ON" position.
- Drive the vehicle at 12 mph (20km/h) or more for 6 minutes or more. (there is no need to drive continuously).
- Stop the vehicle with braking at 25 mph (40km/h) or more.
- Check if the DTC is set.
- Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is DTC C1340 set?
YES Go to Step 1.
NO The procedure is complete.