Malfunction Indicator Light
- Malfunction Indicator Light (MIL) Does Not Come On - Using scan tool, check data list item No. 16 (power supply voltage). If battery voltage exists, go to step 11 . If battery voltage does not exist, go to next step.
- Remove MFI relay from engine compartment relay box. Check MFI relay connector for loose, damaged or corroded terminals. If problem exists, repair connector. If problem does not exist, go to next step.
- Check MFI relay. See FUEL PUMP RELAY & MFI RELAY under RELAYS under MOTORS, RELAYS & SOLENOIDS in SYSTEM & COMPONENT TESTING article. If problem exists, replace MFI relay. If problem does not exist, install MFI relay and go to next step.
- Measure voltage between ground and MFI relay connector terminals No. 3 and 4. See Figure . If battery voltage exists at both terminals, go to next step. If battery voltage does not exist at either or both terminals, repair Red/White wire between engine compartment relay box fuse No. 13 (20-amp) and MFI relay.
- Disconnect ECM connector C-60 or PCM connector C-57. Check ECM connector C-60 or PCM connector C-57 for loose, damaged or corroded terminals. If problem exists, repair connector. If problem does not exist, go to next step.
- Turn ignition on. Measure voltage between ground and ECM connector C-60 terminal No. 82 (Black/White wire) or PCM connector C-57 terminal No. 98 (Black/White wire). See Figure or Figure . If battery voltage exists, go to next step. If battery voltage does not exist, check Black/White wire between ignition switch and ECM/PCM. If problem exists, repair wiring between ignition switch and ECM/PCM. If problem does not exist, check ignition switch. Repair as necessary.
- Turn ignition off. Measure voltage between ground and ECM connector C-60 terminal No. 80 (Orange/Black wire) or PCM connector C-54 terminal No. 66 (Orange/Black wire). If battery voltage exists, go to next step. If battery voltage does not exist, repair Orange/Black wire between engine compartment relay box fuse No. 4 (10-amp) and ECM/PCM.
- Check for continuity between ground and ECM connector C-49 terminals No. 13 (Black wire) and No. 26 (Black wire) or PCM connector C-54 terminals No. 42 (Black wire) and No. 48 (Black wire). If continuity exists at each terminal, go to next step. If continuity does not exist at either terminal, repair appropriate Black wire(s) between ground and ECM/PCM.
- On M/T vehicle, disconnect ECM connector C-53. On all vehicles, measure voltage between ground and ECM connector C-53 terminal No. 38 (White/Violet wire) or PCM connector C-54 terminal No. 49 (White/Violet wire). If battery voltage exists, go to next step. If battery voltage does not exist, repair White/Violet wire between ECM/PCM and MFI relay.
- On M/T vehicle, disconnect ECM connector C-49. On all vehicles, connect jumper wire between ground and ECM connector C-53 terminal No. 38 (White/Violet wire) or PCM connector C-54 terminal No. 49 (White/Violet wire). MFI relay should audibly click. Measure voltage between ground and ECM connector C-49 terminals No. 12 (Red wire) and No. 25 (Red wire) or PCM connector C-54 terminals No. 41 (Red wire) and No. 47 (Red wire). If battery voltage exists at each terminal, replace ECM/PCM. If battery voltage does not exist at either terminal, repair appropriate Red wire between MFI relay and ECM/PCM.
- Check for burned out bulb. If bulb is blown, replace bulb. If bulb is okay, go to next step.
- Disconnect combination meter (instrument cluster) connector C-41. Check combination meter connector C-41 for loose, damaged or corroded terminals. If problem exists, repair connector. If problem does not exist, go to next step.
- Turn ignition on. Measure voltage between ground and combination meter connector C-41 terminal No. 52 (Black/White wire). See Figure . If battery voltage exists, go to next step. If battery voltage does not exist, repair Black/White wire or Green wire between combination meter and ignition switch.
- Turn ignition off. Reconnect combination meter connector. Disconnect ECM connector C-53 or PCM connector C-50. Check ECM connector C-53 or PCM connector C-50 for loose, damaged or corroded terminals. If problem exists, repair connector. If problem does not exist, go to next step.
- Turn ignition on. Measure voltage between ground and ECM connector C-53 terminal No. 36 (Red/Yellow wire) or PCM connector C-50 terminal No. 22 (Red/Yellow wire). See Figure or Figure . If battery voltage exists, replace ECM/PCM. If battery voltage does not exist, repair Red/Yellow wire between combination meter connector and ECM/PCM.
- MIL Stays On - Using scan tool, check for stored DTCs. See ENTERING ON-BOARD DIAGNOSTICS under SELF-DIAGNOSTIC SYSTEM. If DTCs are present, record all DTCs and go to appropriate test(s) under DIAGNOSTIC TESTS . If no DTCs are present, go to next step.
- Turn ignition off. Disconnect combination meter (instrument cluster) connector C-41. See Figure . Check for continuity between ground and combination meter connector C-41 terminal No. 41 (Red/Yellow wire). If continuity exists, repair short to ground in Red/Yellow wire between combination meter and ECM/PCM. If continuity does not exist, replace ECM/PCM.