LEMON Manuals: Even more car manuals for everyone
Home >> Mitsubishi >> 2001 >> Mirage ES, Standard >> Repair and Diagnosis >> Engine Performance >> System >> Engine Controls - Self-Diagnostics >> Diagnostic Tests >> DTC P0300: Random Misfire Detected >> Diagnostic Procedure

Diagnostic Procedure

NOTE: After repairs, verify repair by driving vehicle according to appropriate monitor drive cycle and check for DTCs. See VERIFYING REPAIRS  .
  1. Connect an external tachometer. Using scan tool, read data list item No. 22 (crankshaft position sensor). Check engine RPM during cranking and at idle. If RPM displayed on scan tool and tachometer are equal, go to next step. If RPM displayed on scan tool and tachometer are not equal, go to step  3 .
  2. Connect lab scope pick-up to CKP sensor terminal No. 2 or at ECM connector B37, terminal No .89 (M/T) or B76, terminal No. 54 (A/T) Brown/Green wire. With engine idle speed stable, compare CKP sensor waveform to known-good waveform. See Fig 1 . If waveform is okay, go to step  4 . If waveform is not okay, go to next step.
  3. Turn ignition off. Check CKP sensor connector, ECM connector B37 (M/T) or B76 (A/T) and wiring between ECM and CKP sensor connector. Check CKP sensor and sensing plate for proper installation. If problem exists, repair as necessary. If problem does not exist, replace CKP sensor. Go to step  10 .
  4. Disconnect fuel injector connectors A70, A71, A72 and A73. Check resistance between fuel injector terminals (component side). Resistance should be 13-16 ohms at 68°F (20°C). If resistance is as specified, go to next step. If resistance is not as specified, replace fuel injector. Go to step  10
  5. Using stethoscope, check fuel injector operating sound during cranking or at idle. Ensure frequency of operating sound increases as engine RPM increases. If fuel injectors sound okay, go to next step. If no operating sound is heard from a fuel injector, check fuel injector drive circuit. See DTC P0201-P0204: FUEL INJECTOR NO. 1-4 CIRCUIT MALFUNCTION  .
  6. Start engine and warm to normal operating temperature. Turn all accessories off. Increase engine speed to 2500 RPM. Using scan tool, read data list item No. 81 (long-term fuel compensation). If fuel trim is -12.5-12.5 percent (during closed loop), go to next step. If fuel trim is not as specified, check fuel trim fault. See DTC P0171: SYSTEM TOO LEAN  or DTC P0172: SYSTEM TOO RICH  .
  7. Using scan tool, read data list item No. 82 (short-term fuel compensation). If fuel trim is -17-17 percent (during closed loop), go to next step. If fuel trim is not as specified, check fuel trim fault. See DTC P0171: SYSTEM TOO LEAN  or DTC P0172: SYSTEM TOO RICH  .
  8. Using scan tool, read data list item No. 21 (engine coolant temperature). If temperature displayed on scan tool is equal to actual engine coolant temperature, go to next step. If temperature displayed on scan tool is not equal to actual engine coolant temperature, check ECT circuit. See DTC P0115: ENGINE COOLANT TEMPERATURE (ECT) CIRCUIT HIGH INPUT; DTC P0116: ENGINE COOLANT TEMPERATURE (ECT) CIRCUIT MALFUNCTION; DTC P0117: ENGINE COOLANT TEMPERATURE (ECT) CIRCUIT LOW INPUT  .
  9. Check ignition coil, spark plugs and spark plug wires. See IGNITION CHECKS in BASIC DIAGNOSTIC PROCEDURES article. Check EGR system and EGR valve. See EXHAUST GAS RECIRCULATION (EGR) under EMISSION SYSTEMS & SUBSYSTEMS in SYSTEM & COMPONENT TESTING article. Check for jumped timing belt. See appropriate article in ENGINES. Check compression pressure. See COMPRESSION under MECHANICAL INSPECTION in BASIC DIAGNOSTIC PROCEDURES article. Repair as necessary.
  10. Verify repair by driving vehicle according to other monitor drive cycle and check for DTCs. See OTHER MONITOR  under OBD-II DRIVE CYCLES under VERIFYING REPAIRS. Confirm DTC P0300 does not reset.
Fig 1: Identifying Known-Good CKP Sensor Waveform
G93A80275Courtesy of MITSUBISHI MOTOR SALES OF AMERICA