Diagnostic Procedure
NOTE:
After repairs, verify repair by driving vehicle according to appropriate monitor drive cycle and check for DTCs. See VERIFYING REPAIRS
.
- Turn ignition on. Using scan tool, read data list item No. 13 (intake air temperature). If temperature displayed on scan tool is equal to actual air temperature, go to next step. If temperature displayed on scan tool is not equal to actual air temperature, check air temperature circuit. See DTC P0111: INTAKE AIR TEMPERATURE (IAT) CIRCUIT MALFUNCTION .
- Using scan tool, read data list item No. 21 (engine coolant temperature). If temperature displayed on scan tool is equal to actual engine coolant temperature, go to next step. If temperature displayed on scan tool is not equal to actual coolant temperature, check engine coolant temperature circuit. See DTC P0115: ENGINE COOLANT TEMPERATURE (ECT) CIRCUIT HIGH INPUT; DTC P0116: ENGINE COOLANT TEMPERATURE (ECT) CIRCUIT MALFUNCTION; DTC P0117: ENGINE COOLANT TEMPERATURE (ECT) CIRCUIT LOW INPUT .
- Turn ignition on. On 1.5L, read data list item No. 32 (manifold absolute pressure). On 1.8L, read data list item No. 25 (barometric pressure). Reading should be 101 kPa at 0 ft. (0 m), 95 kPa at 1969 ft. (600 m), 88 kPa at 3937 ft. (1200 m) or 81 kPa at 5906 ft. (1800 m). If scan tool reading is as specified, go to next step. If vehicle has 1.5L engine and scan tool reading is not as specified, check MAP sensor circuit. See DTC P0106: MANIFOLD ABSOLUTE PRESSURE (MAP) SENSOR CIRCUIT MALFUNCTION . If vehicle has 1.8L engine and scan tool reading is not as specified, check barometric pressure circuit. See DTC P0107: BAROMETRIC PRESSURE CIRCUIT LOW INPUT (1.8L) or DTC P0108: BAROMETRIC PRESSURE CIRCUIT HIGH INPUT (1.8L) .
- Disconnect fuel injector connector. Check resistance between fuel injector terminals (component side). Resistance should be 13-16 ohms at 68°F (20°C). If resistance is as specified, go to next step. If resistance is not as specified, replace fuel injector.
- Using stethoscope, check fuel injector operating sound during cranking or at idle. Ensure frequency of operating sound increases as engine RPM increases. If fuel injectors sound okay, go to next step. If no operating sound is heard from a fuel injector, check fuel injector drive circuit. See DTC P0201-P0204: FUEL INJECTOR NO. 1-4 CIRCUIT MALFUNCTION .
- Check fuel injector connectors, A70, A71, A72 and A73. Check ECM connector B40 (M/T) or B77 (A/T) and wiring between ECM and fuel injector connectors. If problem exists, see DTC P0201-P0204: FUEL INJECTOR NO. 1-4 CIRCUIT MALFUNCTION . If wiring and connectors are okay, perform fuel pressure test. See FUEL PRESSURE under FUEL SYSTEM in BASIC DIAGNOSTIC PROCEDURES article. If fuel pressure is okay, go to next step.
- Using scan tool, read data list item No. 81 (long-term fuel compensation). If fuel trim is more than zero (during closed loop), go to step 9 . If fuel trim is less than zero (during closed loop) and vehicle has 1.5L engine, go to step 12 . If fuel trim is less than zero and vehicle has 1.8L engine, go to next step.
- Using scan tool, read data list item No. 12 (volume airflow). Reading should be 18-44 Hz at idle to 68-108 Hz at 2500 RPM. Check that frequency (VAF volume) increases as RPM is increased. If scan tool reading is more than specification, replace VAF sensor. If scan tool reading is less than or equal to specification, check fuel injectors for leakage and fuel for contamination. If problem exists, repair as necessary. If problem does not exist, recheck for DTCs. IF DTC P0171 resets, replace ECM. Go to step 13 .
- Check air intake system for leaks or obstructions. If problem exists, repair as necessary. If problem does not exist and vehicle has 1.5L engine, go to step 11 . If problem does not exist and vehicle has 1.8L engine, go to next step.
- Using scan tool, read data list item No. 12 (volume airflow). Reading should be 18-44 Hz at idle and 68-108 Hz at 2500 RPM. Ensure frequency (VAF volume) increases as RPM is increased. If scan tool reading is less than specification, replace VAF sensor. Go to step 13 . If scan tool reading is more than or equal to specification, go to next step.
- Check fuel injectors for blockage. Check fuel filter and fuel line for blockage. Check fuel pump for insufficient fuel volume. Check for exhaust leaks at HO2S fittings, exhaust manifold, or front pipes. Check for fuel contamination. If problem exists, repair as necessary. If problem does not exist, recheck for DTCs. IF DTC P0171 resets, replace ECM. Go to step 13 .
- Check fuel injectors for leakage and fuel for contamination. If problem exists, repair as necessary. If problem does not exist, recheck for DTCs. IF DTC P0171 resets, replace ECM. Go to next step.
- Verify repair by driving vehicle according to fuel trim monitor drive cycle and check for DTCs. See FUEL TRIM MONITOR under OBD-II DRIVE CYCLES under VERIFYING REPAIRS. Confirm DTC P0171 does not reset.