LEMON Manuals: Even more car manuals for everyone
Home >> Mitsubishi >> 1999 >> 3000GT Base, Standard >> Repair and Diagnosis >> Engine Performance >> System >> Engine Controls - Self-Diagnostics >> Diagnostic Tests >> DTC P0300: Random Misfire Detected >> Diagnostic Procedure

Diagnostic Procedure

NOTE: For connector views, see TERMINAL IDENTIFICATION in SELF-DIAGNOSTICS - INTRODUCTION article.
  1. If using scan tool, go to next step. If using lab scope, connect pick-up to CKP sensor connector terminal No. 2 or ECM connector terminal No. 43. Check waveform of CKP sensor by keeping engine speed constant. Normal pattern is square wave, even pulse width, that toggles between near zero volts and near 5 volts. If CKP sensor pulse width is constant, go to step  4. If CKP sensor pulse width is not constant, go to next step.
  2. NOTE: Tachometer indicates one third of engine speed. So 3 times tachometer speed is actual engine speed. When tachometer is set to 2-cylinder range, it indicates actual engine speed.
  3. Connect tachometer. Using scan tool, check data list item No. 22 (crankshaft position sensor). Cranking speed on scan tool should match tachometer. If tachometer reads zero RPM while cranking, check for bad CKP sensor or broken timing belt. Run engine at idle. Closed throttle position switch should be on. Compare scan tool readings with normal values. See CKP SENSOR SCAN TOOL VALUES  table. If scan tool values are as specified, problem may be intermittent. See INTERMITTENT DTCS . If scan tool readings are not as indicated, go to next step.
    CKP SENSOR SCAN TOOL VALUES

    Coolant Temperature - °F (°C) RPM
    -4 (-20) 1275-1475
    32 (0) 1225-1425
    68 (20) 1100-1300
    104 (40) 950-1150
    176 (80) 600-800
  4. Check CKP sensor connector, ECM connector and wiring harness between ECM and CKP sensor connector. Check CKP sensor and sensing plate for proper installation. Repair as necessary, and then go to step  9. If wiring, connectors and sensor installation are okay, replace CKP sensor, and then go to step  9.
  5. Check injectors and injector circuit. See DTC P0201-P0206: FUEL INJECTOR CYLINDER NO. 1-4 CIRCUIT MALFUNCTION . If injectors and circuit are okay, go to next step.
  6. Start and warm engine. Turn all accessories off. Using scan tool, read data list item No. 81 (long-term fuel compensation). At idle, fuel trim should be -12.5-12.5 percent (during closed loop). If fuel trim is as specified, go to next step. If fuel trim is not as specified, check fuel trim fault. See DTC P0170 & P0173: FUEL TRIM MALFUNCTION .
  7. Using scan tool, read data list item No. 82 (short-term fuel compensation). At 2500 RPM in closed loop operation with no load, fuel trim should be -30-25 percent (Montero), -19-19 percent (3000GT SOHC) or -17-17 percent (3000GT DOHC). If fuel trim is as specified, go to next step. If fuel trim is not as specified, check fuel trim fault. See DTC P0170 & P0173: FUEL TRIM MALFUNCTION .
  8. Using scan tool, read data list item No. 21 (engine coolant temperature). If temperature displayed on scan tool is equal to actual engine coolant temperature as measured with a thermometer, go to next step. If temperature displayed on scan tool is not equal to actual coolant temperature, check ECT circuit. See DTC P0115: ENGINE COOLANT TEMPERATURE (ECT) CIRCUIT MALFUNCTION .
  9. Check ignition coil, spark plugs and spark plug wires. Check injectors. Check ECT sensor. Check for broken timing belt teeth. Check engine compression and EGR system. See BASIC DIAGNOSTIC PROCEDURES article and SYSTEM & COMPONENT TESTING article. Repair as necessary, and then go to next step.
  10. Test drive vehicle following OBD-II drive cycle pattern. See OTHER MONITOR under OBD-II DRIVE CYCLES in SELF-DIAGNOSTICS - INTRODUCTION article. Check scan tool for DTCs. Confirm DTC does not reset.