LEMON Manuals: Even more car manuals for everyone
Home >> Mini >> 2014 >> Cooper Base, 2D Convertible, Automatic Trans >> Repair and Diagnosis >> Quick Lookups >> Technical Bulletins >> Technical Service Bulletins >> Other Variant >> Suspension Control Systems >> Check Control Message: Tire Pressure Monitor (RDCI) Failure (M36 01 15)

Check Control Message: Tire Pressure Monitor (RDCI) Failure (M36 01 15)

WARNING: This page is about the Cooper Base, 2D Hatchback, Automatic Trans, which is a different variant/trim than selected.
Publication date: 2016-02-01
Reference number: M36 01 15

CHECK CONTROL MESSAGE: TIRE PRESSURE MONITOR (RDCI) FAILURE

CHECK CONTROL MESSAGE: TIRE PRESSURE MONITOR (RDCI) FAILURE

TECHNICAL SERVICE BULLETIN

Reference Number(s): SI M36 01 15, Date of Issue:  February 2016
MINI: F54 (Clubman); F55 (4-Door Hardtop); F56 (2-Door Hardtop); Produced from SOP to 1/18/2016
GROUP: Wheel and Tires
Superceded Bulletin(s): SI 36 01 15, Date of Issue:  June 2015
NOTE: This Service Information bulletin supersedes SI 36 01 15 dated June 2015. 

SUBJECT

Check Control Message: Tire Pressure Monitor (RDCi) Failure 

SITUATION

A Check Control Message states Tire Pressure Monitor (RDCi) has failed

CAUSE

Hardware failure in the remote control unit (FBD3 antenna)

PROCEDURE

Perform vehicle test and identify fault codes stored in the Dynamic Stability Control (DSC) unit.

  1. 0x48069E RDCi Unable to calibrate wheel detection system
  2. 0x4806B8 RDCi No reception, front left wheel electronics
  3. 0x4806DA RDCi No reception, front right wheel electronics
  4. 0x4806F0 RDCi No reception, rear left wheel electronics
  5. 0x4806F4 RDCi No reception, rear right wheel electronics
  6. 0x4809EB RDCi No reception, wheel electronics (position unknown)

If one or more of the fault codes listed is entered in the DSC unit, proceed as follows:

The initialization is successful once the wheels have turned green in the RDCi menu of the control display.

If the initialization is not successful, run the vehicle test with ISTA/D and work through the corresponding test module.

PARTS INFORMATION

PARTS INFORMATION

Part Number Description Quantity
Refer to ETK/EPC Remote Control Unit (FBD3 antenna) 1

WARRANTY INFORMATION

Covered under the terms of the MINI New Passenger Car Limited Warranty or the MINI NEXT Certified Pre-Owned Limited Warranty.

WARRANTY INFORMATION

Defect Code:  66 10 03 15 00 
WARRANTY INFORMATION

Labor Operation: Labor Allowance: Description:
00 00 006 Refer to KSD2 Performing "vehicle test" (with vehicle diagnosis system - checking faults)
And:
61 21 528 Refer to KSD2 Charging battery
And:
61 31 863 Refer to KSD Removing and installing radio remote control unit Replacing radio remote control unit (after vehicle diagnosis)
And:
36 11 100 4 FRU Work time to check tire pressures, correct if necessary, perform the initialization test drive.

If you are using a Main labor code for another repair, use the Plus code labor operation 00 00 556 instead.

Refer to KSD2 for the corresponding flat rate unit (FRU) allowances.

Work time labor operation code 36 11 100 is not considered a Main labor operation. Also, since the "work time" FRU allowance to be claimed is specified, a separate punch time is not required.

OTHER REPAIRS

If performing ISTA diagnostics and related test plans results in other eligible and covered work, claim this work with the applicable defect code and/or labor operations listed in KSD2.