General Specifications
WARNING: This page is about a different variant/trim than selected.
GENERAL SPECIFICATIONS
| Item | Specification | ||
|---|---|---|---|
| Lubricants | |||
| Super Premium SAE 5W30 Motor Oil XO-5W30-QSP | WSS-M2C153-H | ||
| High-temperature grease | ESD-M1C220-A | ||
| Manual Transaxle Fluid | WSD-M2C200-C | ||
| Mercon® Multi-Purpose Automatic Transmission Fluid (automatic transaxle) XT-2-QDX | Mercon® | ||
| Extended Life Engine Coolant F6AZ - 19544-AA | WSS-M97B44-A | ||
| Gasket Maker F8AZ-19B508-AB | WSK-M2G348-A5 | ||
| Silicone Gasket and Sealant F7AZ - 19554-EA | WSE-M4G323-A4 | ||
| High Temperature Nickel Anti-Seize Lubricant F6AZ -9L494-AA | ESE-M12A4-A | ||
| High Performance DOT3 Motor Vehicle Brake Fluid C6AZ-19542-AB | ESA-M6C25-A | ||
| High performance brake fluid DOT 4 | SAM-6C9103-A | ||
| Capacities | |||
| Engine oil, initial fill incl. filter | 4.50 | ||
| Engine oil, oil change incl. filter | 4.25 | ||
| Engine oil, oil change excl. filter | 3.75 | ||
| Coolant | 6.6 | ||
| Transmission fluid (manual transaxle) | 2.6 | ||
| Transmission fluid (automatic transaxle with oil cooler)(1) | 7.2(1) | ||
| Cylinder Block | |||
| Number of main bearings | 5 | ||
| Cylinder bore diameter, class 1 | 84.800-84.810 | ||
| Cylinder bore diameter, class 2 | 84.810-84.820 | ||
| Cylinder bore diameter, class 3 | 84.820-84.830 | ||
| Inside diameter-main bearing shells (installed) | 58.011-58.038 | ||
| Inside diameter-main bearing shells (installed) (main bearing shells graded by size) | 58.008-58.031 | ||
| Main bearing radial clearances | 0.011-0.058 | ||
| Main bearing radial clearances (main bearing shells graded by size) | 0.0196-0.044 | ||
| Main bearing parent bore | 62.287-62.300 | ||
| Crankshaft | |||
| Main bearing journal dia. | 57.980-58.000 | ||
| Main bearing journal end float | 0.09-0.26 | ||
| Big-end bearing journal dia. | 46.89-46.91 | ||
| Lower Crankcase | |||
| Required shim thickness where there is a gap between the cylinder block and the lower crankcase: | |||
| 0.26 mm to 0.50 mm | 0.25 | ||
| 0.51 mm to 0.75 mm | 0.50 | ||
| Connecting Rods | |||
| Bore diameter, big-end | 49.89-49.91 | ||
| Bore diameter, small end | 19.951-19.981 | ||
| Inside diameter-big-end bearing shells (fitted) | 46.926-46.960 | ||
| Big-end bearing radial clearance | 0.016-0.070 | ||
| Big-end bearing axial clearance | 0.090-0.320 | ||
| Pistons | |||
| Piston diameter, class 1 | 84,750-84,760 | ||
| Piston diameter, class 2 | 84,760-84,770 | ||
| Piston diameter, class 3 | 84,770-84,780 | ||
| Piston clearance in cylinder | -0,010-0,030 | ||
| Piston ring gaps (fitted) | |||
| - Upper compression ring | 0,22-0,37 | ||
| - Lower compression ring | 0,50-0,70 | ||
| - Oil scraper ring | 0,15-0,66 | ||
| Ring gap positions | The piston ring gaps must be spaced evenly around the circumference of the piston. This also applies to the elements of the oil scraper ring. Stagger the ring gaps at 120 degrees to one other | ||
| Piston Pins | |||
| Piston pin length | 55.80-56.20 | ||
| Piston pin diameter | 19.997-20.000 | ||
| Piston pin diameter, red | 20.625-20.628 | ||
| Piston pin clearance in connecting rod bore | 0.016-0.049 | ||
| Camshaft | |||
| Number of camshaft bearings | 5 | ||
| Drive | Timing belt | ||
| Bearing journal diameter | 25.960-25.980 | ||
| Camshaft bearing radial clearance | 0.020-0.070 | ||
| Camshaft end float | 0.080-0.220 | ||
| Valves | |||
| Valve clearance in valve guide | |||
| - intake valve | 0.017-0.064 | ||
| - exhaust valve | 0.017-0.064 | ||
| Valve clearance-intake valve (at 20°C +/- 5°C) | 0.11-0.18 | ||
| Valve clearance-exhaust valve (at 20°C +/- 5°C) | 0.27-0.34 | ||
| Cylinder Head | |||
| Maximum distortion (mating face) | 0,1 | ||
| Mating face height | 2.0 +0.12 -0.24 | ||
| Mating face peak-to-valley height (reference length 2,5 mm at right angles to direction of grooves) | R 3Z = 6.0 | ||
| Oil pressure at 800-850 rpm 1.3 | -2.5 | ||
| Oil pressure at 4000 rpm | 3.7 -5.5 | ||
|
|||