LEMON Manuals: Even more car manuals for everyone
Home >> Mercury >> 2002 >> Cougar 2.5 L, Standard >> Repair and Diagnosis >> Engine Mechanical >> Mechanical >> Engine - 2.5L >> In-Vehicle Repair >> Timing Drive Components >> Installation

Timing Drive Components: Installation

CAUTION: Failure to verify correct timing drive component alignment will result in severe engine damage.
    NOTE: Install the sprockets with the timing marks out.
    Fig 1: Installing Crankshaft Sprockets
    G03418826Courtesy of FORD MOTOR CO.
  1. Install the crankshaft sprockets.
  2. NOTE: LH shown, RH similar.
    Fig 2: Positioning Chain Tensioner In A Soft-Jawed Vise
    G03418827Courtesy of FORD MOTOR CO.
  3. Position the chain tensioner in a soft-jawed vise.
  4. NOTE: LH shown, RH similar.
    Fig 3: Holding Chain Tensioner Ratchet Lock Mechanism Away
    G03418828Courtesy of FORD MOTOR CO.
  5. Hold the chain tensioner ratchet lock mechanism away from the ratchet stem with a small pick.
  6. CAUTION: During tensioner compression, do not release the ratchet stem until the tensioner piston is fully bottomed in its bore or damage to the ratchet stem will result.
  7. Slowly compress the timing chain tensioner.
  8. Retain the tensioner piston with a 1.5 mm (0.06 in) wire or paper clip.
    Fig 4: Retaining Tensioner Piston With Wire Or Paper Clip
    G03418829Courtesy of FORD MOTOR CO.
  9. If the timing marks on the timing chains are not evident, use a permanent-type marker to mark on the LH and the RH timing chains.
    1. Mark any link to use as the crankshaft timing mark.
    2. Starting with the crankshaft timing mark, count 29 links and mark the link.
    3. Continue counting to 42 and mark the link.
      Fig 5: Marking Timing Chain
      G03418830Courtesy of FORD MOTOR CO.
  10. Position the LH timing chain and guide and install the bolts.
    • Align the marks on the timing chain with the marks on the camshaft and crankshaft sprockets.
      Fig 6: Aligning Marks On Timing Chain
      G03418831Courtesy of FORD MOTOR CO.
  11. Install the LH timing chain tensioner and tensioner arm.
    1. Install the tensioner arm.
    2. Position the tensioner.
    3. Install the bolts.
      Fig 7: Installing LH Timing Chain Tensioner And Tensioner Arm
      G03418832Courtesy of FORD MOTOR CO.
  12. Install the crankshaft damper bolt and rotate the crankshaft clockwise 120 degrees until the crankshaft keyway is in the 3 o'clock position.
    Fig 8: Installing Crankshaft Damper Bolt
    G03418833Courtesy of FORD MOTOR CO.
  13. Verify that the RH camshafts are correctly positioned.
    Fig 9: Verifying RH Camshafts Are Correctly Positioned
    G03418834Courtesy of FORD MOTOR CO.
  14. Position the RH timing chain and chain guide and install the bolts.
    • Align the marks on the timing chain with the marks on the camshaft and crankshaft sprockets.
      Fig 10: Aligning RH Timing Chain With Marks On Camshaft & Crankshaft Sprockets
      G03418835Courtesy of FORD MOTOR CO.
  15. Install the RH timing chain tensioner and tensioner arm.
    1. Install the tensioner arm.
    2. Position the tensioner.
    3. Install the bolts.
      Fig 11: Installing RH Timing Chain Tensioner And Tensioner Arm
      G03418836Courtesy of FORD MOTOR CO.
  16. Remove the LH and RH timing chain tensioner piston retaining wires.
  17. Rotate the crankshaft counterclockwise 120 degrees to top dead center (TDC).
  18. CAUTION: Failure to verify correct timing drive component alignment will result in severe engine damage.
  19. Verify the timing with the following steps.
    1. There should be 12 chain links between the front camshaft timing marks.
    2. There should be 27 chain links between the camshaft and crankshaft timing marks.
    3. There should be 30 chain links between the camshaft and crankshaft timing marks.
      Fig 12: Verifying Timing Component Alignment
      G03418837Courtesy of FORD MOTOR CO.
  20. Remove the crankshaft damper bolt.
    Fig 13: Removing Crankshaft Damper
    G03418838Courtesy of FORD MOTOR CO.
  21. NOTE: LH shown, RH similar.
    Fig 14: Installing LH And RH Spark Plugs
    G03418839Courtesy of FORD MOTOR CO.
  22. Install the LH and RH spark plugs.
  23. CAUTION: This pulse wheel is used in several different engines. Install the pulse wheel with the keyway in the slot stamped "20-25-34Y-30M" (color blue).
    Fig 15: Installing Ignition Pulse Wheel
    G03418840Courtesy of FORD MOTOR CO.
  24. Install the ignition pulse wheel.
  25. Install the engine front cover. For additional information, refer to ENGINE FRONT COVER .