Test F: Single Door Lock Is Inoperative (Driver Door Only Remote System)
NOTE:
Use both remote transmitters during this test. If requested function does not work from only one transmitter and all other functions operate from remote transmitter in question, replace remote transmitter in question and retest system operation.
- Check For Liftgate Lock - Check to see if vehicle has a power liftgate lock. If vehicle is equipped with power liftgate lock, go to next step. If vehicle is not equipped with power liftgate lock, go to step 3).
- Check Driver Door Lock Operation Using Remote Transmitter - Press trunk button on remote transmitter. Liftgate should unlock. Press unlock button on remote transmitter. Driver door should unlock. Press unlock button on remote transmitter twice within 5 seconds. Driver door should unlock. Press lock button on remote transmitter. Driver door and liftgate should lock. If only driver door unlocks when transmitter unlock button is pressed twice, go to step 4). If liftgate does not unlock, go to step 8). If liftgate does not lock, go to step 12). If both the driver and liftgate locks do not lock, go to step 14). If both the driver and liftgate locks do not unlock, replace RAP module and retest system operation. If driver door does not lock, go to step 17). If driver door lock is completely inoperative, go to step 10). If liftgate lock is completely inoperative, go to step 18).
- Check Driver Door Lock Operation - Press unlock button on remote transmitter. Driver door should unlock. Press unlock button on remote transmitter twice within 5 seconds. Driver door should unlock. Press lock button on remote transmitter. Driver door should lock. If only driver door unlocks when transmitter unlock button is pressed twice, go to next step. If driver door does not lock, go to step 5). If driver door lock does not operate only in one direction, perform TEST A : ALL DOOR LOCKS ARE INOPERATIVE (DRIVER DOOR ONLY REMOTE SYSTEM).
- Check Purple Wire For Open - Turn ignition off. Disconnect RAP module Gray, 26-pin connector C405 (located in luggage compartment/trunk, behind right trim panel on ZX2 coupe and sedan, or located behind left rear quarter trim panel on wagon). Connect a jumper wire between ground and RAP module 26-pin connector C405 terminal No. 1 (Purple wire). See Figure . If driver door does not unlock, go to next step. If driver door unlocks, replace RAP module and retest system operation.
- Check Purple Wire For Open - Disconnect door lock relay. See DOOR LOCK RELAY under REMOVAL & INSTALLATION. Using an ohmmeter, check resistance in Purple wire between door lock relay connector terminal No. 2 and RAP module 26-pin connector C405 terminal No. 1. See Figure and Figure . If resistance is less than 5 ohms, replace door lock relay and retest system operation. If resistance is 5 ohms or more, repair open in Purple wire and retest system operation.
- Check Gray Wire For Open - Turn ignition off. Disconnect RAP module Gray, 22-pin connector C404 (located in luggage compartment/trunk, behind right trim panel on ZX2 coupe and sedan, or located behind left rear quarter trim panel on wagon). Ensure driver door is unlocked. Connect a jumper wire between ground and RAP module 22-pin connector C404 terminal No. 17 (Gray wire). See Figure . If driver door does not lock, go to next step. If driver door locks, replace RAP module and retest system operation.
- Check Gray Wire For Open - Disconnect door lock relay. See DOOR LOCK RELAY under REMOVAL & INSTALLATION. Using an ohmmeter, check resistance in Gray wire between door lock relay connector terminal No. 4 and RAP module 22-pin connector C404 terminal No. 17. See Figure and Figure . If resistance is less than 5 ohms, replace door lock relay and retest system operation. If resistance is 5 ohms or more, repair open in Gray wire and retest system operation.
- Check Green/Black Wire For Open - Turn ignition off. Disconnect RAP module Gray, 22-pin connector C404 (located in luggage compartment/trunk, behind right trim panel on ZX2 coupe and sedan, or located behind left rear quarter trim panel on wagon). Connect a jumper wire between ground and RAP module 22-pin connector C404 terminal No. 7 (Green/Black wire). See Figure . If liftgate does not unlock, go to next step. If liftgate unlocks, replace RAP module and retest system operation.
- Check Green/Black Wire For Open - Disconnect door lock relay. See DOOR LOCK RELAY under REMOVAL & INSTALLATION. Using an ohmmeter, check resistance in Green/Black wire between door lock relay connector terminal No. 7 and RAP module 22-pin connector C404 terminal No. 7. See Figure and Figure . If resistance is less than 5 ohms, replace door lock relay and retest system operation. If resistance is 5 ohms or more, repair open in Green/Black wire and retest system operation.
- Check Red/White Wire For Open - Turn ignition off. Disconnect door lock relay. See DOOR LOCK RELAY under REMOVAL & INSTALLATION. Disconnect driver door lock actuator connector. Using an ohmmeter, check resistance in Red/White wire between door lock relay connector terminal No. 6 and driver door lock actuator connector. See Figure . If resistance is less than 5 ohms, go to next step. If resistance is 5 ohms or more, repair open in Red/White wire and retest system operation.
- Check Green/Orange Wire For Open - Using an ohmmeter, check resistance in Green/Orange wire between door lock relay connector terminal No. 3 and driver door lock actuator connector. See Figure . If resistance is less than 5 ohms, replace driver door lock actuator and retest system operation. If resistance is 5 ohms or more, repair open in Green/Orange wire and retest system operation.
- Check Black Wire For Open - Using an ohmmeter, check resistance between ground and door lock relay connector terminal No. 11 (Black wire). See Figure . If resistance is less than 5 ohms, go to next step. If resistance is 5 ohms or more, repair open in Black wire and retest system operation.
- Check Green/Orange Wire For Open - Using an ohmmeter, check resistance between ground and door lock relay connector terminal No. 3 (Green/Orange wire). See Figure . Press lock button on remote transmitter. If liftgate locks, replace door lock relay and retest system operation. If liftgate does not lock, repair open in Green/Orange wire and retest system operation.
- Check Gray Wire For Open - Turn ignition off. Disconnect RAP module Gray, 22-pin connector C404 (located in luggage compartment/trunk, behind right trim panel on ZX2 coupe and sedan, or located behind left rear quarter trim panel on wagon). Ensure driver door is unlocked. Connect a jumper wire between ground and RAP module 22-pin connector C404 terminal No. 17 (Gray wire). See Figure . If driver door does not lock, go to next step. If driver door locks, replace RAP module and retest system operation.
- Check Gray Wire For Open - Disconnect door lock relay. See DOOR LOCK RELAY under REMOVAL & INSTALLATION. Using an ohmmeter, check resistance in Gray wire between door lock relay connector terminal No. 4 and RAP module 22-pin connector C404 terminal No. 17. See Figure and Figure . If resistance is less than 5 ohms, go to next step. If resistance is 5 ohms or more, repair open in Gray wire and retest system operation.
- Check Green/Orange Wire For Open - Disconnect driver door lock actuator connector. Using an ohmmeter, check resistance in Green/Orange wire between door lock relay connector terminal No. 3 and driver door lock actuator connector. See Figure . If resistance is less than 5 ohms, replace door lock relay and retest system operation. If resistance is 5 ohms or more, repair open in Green/Orange wire and retest system operation.
- Check Door Lock Relay - Test door lock relay. See DOOR LOCK RELAY under COMPONENT TESTING. If door lock relay is okay, replace RAP module and retest system operation. If door lock relay is not okay, replace door lock relay and retest system operation.
- Check Pink Wire For Open - Turn ignition off. Disconnect door lock relay. See DOOR LOCK RELAY under REMOVAL & INSTALLATION. Disconnect liftgate lock actuator connector. Using an ohmmeter, check resistance in Pink wire between door lock relay connector terminal No. 1 and liftgate lock actuator connector. See Figure . If resistance is less than 5 ohms, go to next step. If resistance is 5 ohms or more, repair open in Pink wire and retest system operation.
- Check Green/Orange Wire For Open - Using an ohmmeter, check resistance in Green/Orange wire between door lock relay connector terminal No. 3 and liftgate lock actuator connector. See Figure . If resistance is less than 5 ohms, replace liftgate lock actuator and retest system operation. If resistance is 5 ohms or more, repair open in Green/Orange wire and retest system operation.