LEMON Manuals: Even more car manuals for everyone

Remove/install front roof frame - AR65.20-P-1006GQ

MODEL 166 

Shown on model 166.0 

Fig 1: Identifying Front Roof Frame Remove/Install Components - Shown On Model 166.0
G09982817Courtesy of MERCEDES-BENZ USA
DANGER Risk of injury  caused by scraping or cutting body parts on sharp vehicle parts Always wear protective gloves when working on or near sharp and non-deburred vehicle parts.
Deburr repair panels.
AS00.00-Z-0017-01A
DANGER The high voltage used for electric welding presents a lethal hazard. Risk of explosion  from welding in areas close to highly inflammable materials. Risk of injury  from weld splatter and UV-light when welding. Risk of poisoning  from inhaling welding gases Use insulating mats. Wear protective clothing, safety glasses and a protective mask. Remove highly flammable materials from the hazard area. Use air extraction system. AS00.00-Z-0007-01A
IMPORTANT General information on MB materials   AH98.00-P-9409-03A
IMPORTANT Pretreatment of bonding surfaces   AH60.00-P-0008-01SX
IMPORTANT General information on repair of vehicles with ultra-strength steels.   AH60.00-P-0024-01N
IMPORTANT General information on body repair   AH60.00-N-0001-01A
IMPORTANT Measures for preventing damage to components when performing electric welding and soldering work   AH60.00-P-0001-02A
REMOVING Remove     
1 Remove all detachable parts in area to be repaired    
2 Cover all detachable parts remaining in vehicle with fire-resistant welding protection blanket    
3.1 Remove center roof paneling MODEL 166
without CODE 413 (Automatic panoramic sliding sunroof)
 
Replace complete center roof paneling AR65.10-P-1000GQ 
3.2 Remove panoramic roof frame MODEL 166
with CODE 413 (Automatic panoramic sliding sunroof)
 
Remove/install panoramic roof frame AR77.21-P-0800GQ
4 Separate front roof frame (1) Separate front roof frame AR65.20-P-1006-02GQ
Zinc dust paint suitable for spot welding *BR00.45-Z-1001-07A 
5 Prepare front roof frame (1) for installation Prepare front roof frame for installation AR65.20-P-1006-04GQ
Zinc dust paint suitable for spot welding *BR00.45-Z-1001-07A 
INSTALLING Install     
6 Install front roof frame (1) Install front roof frame AR65.20-P-1006-05GQ
Blind rivet 6.5X12.5 *BR00.45-Z-1012-13A 
Blind rivet, 6.5 x 14.5
MIG-MAG inert gas welder (steel, brazing, aluminum)
*BR00.45-Z-1016-13A 
7 Install center roof paneling MODEL 166
without CODE 413 (Automatic panoramic sliding sunroof)
 
Replace complete center roof paneling AR65.10-P-1000GQ 
8 Clean weld joints and sheet metal flanges with rotary wire brush    
9 Clean repair area    
10 Remove welding protection blankets IMPORTANT On all covered parts remaining in vehicle.  
DANGER Risk of explosion  caused by paint vapors igniting. Risk of poisoning  caused by inhaling paint vapors. No smoking! No open fire! Use respiratory protection, protective clothing, gloves, safety glasses and protective skin cream. Ensure that the area is well ventilated. AS98.00-Z-0002-01A
11 Prime repair area with primer filler Use only primer filler approved by Daimler AG
↓
 
12 Carry out seam sealing after repairs Seam sealing following repair AR97.10-P-4000GQ
DANGER Risk of explosion  caused by paint vapors igniting. Risk of poisoning  caused by inhaling paint vapors. No smoking! No open fire! Use respiratory protection, protective clothing, gloves, safety glasses and protective skin cream. Ensure that the area is well ventilated. AS98.00-Z-0002-01A
13 Paint repair area adjacent surfaces Use only paints approved by Daimler AG
↓
 
14 Apply additional cavity preservation Cavity preservation following repair work AR97.20-P-1500GQ
15 Install panoramic roof frame MODEL 166
with CODE 413 (Automatic panoramic sliding sunroof)
 
Remove/install panoramic roof frame AR77.21-P-0800GQ
16 Install all detachable body components in area to be repaired    
REPAIR MATERIALS

Number Designation Order number
BR00.45-Z-1001-07A Zinc dust paint suitable for spot welding A 000 986 34 42
BR00.45-Z-1012-13A Blind rivet 6.5X12.5 A 004 990 16 97
BR00.45-Z-1016-13A Blind rivet, 6.5 x 14.5 A 004 990 17 97