LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2013 >> ML63 >> Repair and Diagnosis >> Engine Performance >> Ignition System >> Electrical System - Engine - 166 Chassis >> Testing & Repair >> Remove/install ignition coils >> Remove/install ignition coils - AR15.12-P-2003GQ

Remove/install ignition coils - AR15.12-P-2003GQ

ENGINE 276 in MODEL 166, 251 

Fig 1: Identifying Ignition Coils Remove/Install Components - Shown On Model 166.0
G09981897Courtesy of MERCEDES-BENZ USA

Shown on model 166.0 with engine 276.9 

DANGER Risk of injury  caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof. No parts of the body or limbs should be within the operating area when the components are moving. AS00.00-Z-0011-01A
DANGER Risk of death  caused by contact with parts conducting high voltages. Do not touch parts which conduct high voltages. Persons who have electronic implants (e.g. cardiac pacemakers) should never perform any work on the ignition system. AS15.10-Z-0001-01A
DANGER Risk of injury  . Skin or eye injuries may result when handling hot or glowing objects. Wear protective gloves, protective clothing and safety glasses, if necessary. AS00.00-Z-0002-01A
NOTES Notes on avoiding damage to ignition system   AH15.10-P-0002-01V
REMOVINGINSTALLING Remove/install     
1 Switch off ignition    
2 Remove partition wall between wheel wells ENGINE 276 in MODEL 251  
3.1 Remove upper engine covers ENGINE 276.8 in MODEL 166, 251  
3.2 Remove front engine cover (1) and rear engine cover (3) ENGINE 276.9 in MODEL 166, 251  
4 Remove intake manifold ENGINE 276.9 in MODEL 166, 251  
AR09.20-P-1961GQ
5.1 Remove both engine air intake ducts upstream of air filter and air filter housing ENGINE 276.8 in MODEL 166, 251  
AR09.10-P-1150GQC
5.2 Remove air filter housing (2) ENGINE 276.9 in MODEL 166, 251  
TORQUE SPECIFICATION Bolt, air filter to cylinder head cover *BA09.10-P-1001-01M 
TORQUE SPECIFICATION Bolt, air filter to air intake pipe support brace *BA09.10-P-1002-01M 
6 Remove insulation at the rail    
7 Disconnect connector (4) from ignition coils (T1/1 to T1/6)    
8 Remove screw/bolts (5) of ignition coils (T1/1 to T1/6) TORQUE SPECIFICATION Screw/bolt, ignition coil to cylinder head cover *BA15.10-P-1001-04A 
9 Pull ignition coils (T1/1 up to T1/6) with spark plug connectors (a) upwards and out IMPORTANT The ignition coils (T1/1 to T1/6) and the spark plug connector (a) create a device and can therefore only be removed and replaced together.  
INSPECT Check     
10 Check ignition coils (T1/1 up to T1/6) and spark plug connectors (a) for damage and replace if necessary    
11 Install in the reverse order    
12 Read out fault memory using the diagnostic system and clear if necessary    
REFER TO SELF-DIAGNOSTIC SYSTEMS     AD00.00-P-2000-04A
AIR FILTER

Number Designation ENGINE 276.9
BA09.10-P-1001-01M Bolt, air filter to cylinder head cover Nm 9
AIR FILTER

Number Designation ENGINE 276.9
BA09.10-P-1002-01M Bolt, air filter to air intake pipe support brace Nm 9
IGNITION COIL

Number Designation ENGINE 276
BA15.10-P-1001-04A Screw/bolt, ignition coil to cylinder head cover Nm 9