LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2006 >> R500 >> Repair and Diagnosis >> Engine Performance >> Ignition System >> Mixture Formation -- R500 >> Basic Knowledge >> ME-SFI fuel injection and ignition system engine electronics function - GF07.61-P-0001BK

ME-SFI fuel injection and ignition system engine electronics function - GF07.61-P-0001BK

ENGINE 113.967 in MODEL 219 

ENGINE 113.964 in MODEL 164.1 up to Model Year 8 

ENGINE 113.971 in MODEL 251 up to Model Year 8 

The following functions are combined in the ME-SFI control unit:

The ME control unit evaluates the following basic information:

Section in cylinder plane 

Fig 1: Identifying Fuel Injection System Components
G07302047Courtesy of MERCEDES-BENZ USA

Fuel injection system 

The fuel is injected by the fuel injection valves, which spray the atomized fuel in a fine spray front of the intake valves. These are actuated sequentially by the ME control unit, in other words an injection valve is assigned to each cylinder and meters the quantity of fuel which is calculated for the cylinder.

The main measured variable for determining the fuel volume is the air mass supplied to the engine and detected by the hot film mass air flow sensor.

Ignition system 

Ignition timing is map-controlled by the ME control unit. Each cylinder has a spark plug located centrally in the combustion chamber with an ignition coil plugged in directly.

The high voltage is distributed without the use of moving parts, directly by the ignition coils to the spark plugs (rotorless high voltage distribution). The antiknock control (AKC) function is integrated in the ME-SFI control unit. Knock detection is carried out by two knock sensors.

CAN data bus 

The individual control unit are networked with each other via the CAN data bus (C  ontroller-A  rea-N  etwork) dependent on equipment and model. The following control units are responsible for the engine control:

IMPORTANT The engine control unit is flashable. The required software for the control unit programming is contained on the STAR DIAGNOSIS DAS update DVD.

Exhaust gas recirculation 

A combined exhaust gas recirculation valve with electric vacuum transducer is installed behind the right bank of cylinders. The exhaust gas recirculation valve is opened at varying degrees and the quantity of the recirculated exhaust gases is thus determined.

Electronic accelerator 

No mechanical link between accelerator pedal and throttle valve actuator. The accelerator pedal sensor detects the accelerator pedal input for the ME control unit.

Accelerator pedal adaptation 

The engine control unit recognizes how the accelerator pedal is being actuated and switches between characteristic curves. After approx. 50% pedal travel by a sporty driver, around 80% of engine load is released and by a smooth driver, around 40%. There is no further difference felt above a pedal travel of about 90%.

Enabling of engine control 

An engine start is only possible in combination with a drive authorization system (DAS 3). The ME control unit is networked with the DAS via the CAN.

Intake manifold switchover 

When the engine is running away, at around 3500 RPM, the intake manifold length is switched from long to short via flaps.

Actuation of the length switching valves takes place electro-pneumatically in the intake manifold. A vacuum memory is integrated in the intake manifold.

Secondary air injection 

The electric air pump is positioned at the front of the engine. A combination valve (air shutoff valve with check valve) is flanged to the front of the cylinder head of each bank of cylinders. The air pump switchover valve is operated parallel to the electric air pump.

Idle speed control 

The idle speed is controlled by the throttle valve actuator, which is operated by the ME control unit, by altering the position of the throttle valve. In addition, the injection quantity and the ignition angle are adapted in neutral. At undervoltage or when the AC system is connected, the idle speed can be increased to around 750/min.

Fig 2: Identifying ME Control Unit (ME 2.8)
G07302048REFER TO GENERAL INFORMATIONUSA ONLYCourtesy of MERCEDES-BENZ USA
  Motor electronics (ME-SFI) fuel injection and ignition system, arrangement of components Location of components at engine end GF07.61-P-0001-01BK 
    Location of components on the vehicle side Model 219 with engine 113 GF07.61-P-0001-01BL
    Location of components on the vehicle side Models 164.1, 251 with engine 113 GF07.61-P-0001-01BM 
  Motor electronics (ME-SFI) fuel injection and ignition system function diagram   GF07.61-P-0001-02BK 
  Motor electronics (ME-SFI) fuel injection and ignition system control unit input signals   GF07.61-P-0001-06BK 
  Motor electronics (ME-SFI) fuel injection and ignition system control unit output signals   GF07.61-P-0001-07BK 
  ME-SFI fuel injection and ignition system model and component installation survey   GF07.61-P-0001-12BK 
  ME-SFI ignition ON function   GF07.61-P-3005BK 
  ME-SFI starting function   GF07.61-P-2003BK 
  ME-SFI idle speed function   GF07.61-P-2006BK 
  ME-SFI driving mode function   GF07.61-P-2005BK 
  ME-SFI diagnosis fault memory function   GF07.61-P-2004BK 
  CAN data bus, function   GF54.00-P-0005BK
REFER TO GENERAL INFORMATION ME-SFI vehicle features USA ONLY AH07.61-P-0002-02BK 
  Motor electronics (ME-SFI) fuel injection and ignition system - survey of system components, location/task/design/function   GF07.61-P-9999BK