LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2017 >> 5 GT, Standard Trans >> Repair and Diagnosis >> Engine Mechanical >> Mechanical >> Engine Mechanical System >> Variable Valve Timing Actuator Removal/Installation

Variable Valve Timing Actuator Removal/Installation

NOTE:
  • Variable valve timing actuator can not be disassembled because it is a precision unit.
  • Intake camshaft sprocket is integrated with the variable valve timing actuator and cannot be disassembled.
  1. Remove the battery cover. (See BATTERY REMOVAL/INSTALLATION .)
  2. Disconnect the negative battery cable.
  3. Remove the plug hole plate. (See PLUG HOLE PLATE REMOVAL/INSTALLATION .)
  4. Disconnect the wiring harness.
  5. Remove the ignition coils. (See IGNITION COIL REMOVAL/INSTALLATION .)
  6. Remove the spark plugs. (See SPARK PLUG REMOVAL/INSTALLATION .)
  7. Remove the ventilation hose.
  8. Remove the oil level gauge.
  9. Remove the cylinder head cover. (See TIMING CHAIN REMOVAL/INSTALLATION .)
  10. Remove the aerodynamic under cover and splash shield as a single unit. (See AERODYNAMIC UNDER COVER REMOVAL/INSTALLATION .) (See SPLASH SHIELD REMOVAL/INSTALLATION .)
  11. Remove the drive belt. (See DRIVE BELT REMOVAL/INSTALLATION .)
  12. Remove the nut shown in the figure and set the power steering pipe component out of the way.
    Fig 1: Power Steering Pipe Component Nut With Torque Specification
    G13726568Courtesy of MAZDA MOTORS CORP.
  13. Remove the engine front cover lower blind plug.
    G13726596Courtesy of MAZDA MOTORS CORP.
  14. Remove the engine front cover upper blind plug.
    G13726597Courtesy of MAZDA MOTORS CORP.
  15. Disconnect the drive shaft (RH) from joint shaft, set the drive shaft (RH) out of the way. (MTX) (See DRIVE SHAFT REMOVAL/INSTALLATION .)
  16. Remove the cylinder block lower blind plug, and install the SST.
    G13726627Courtesy of MAZDA MOTORS CORP.
  17. Rotate the crankshaft in the direction of the engine rotation so that the No. 1 piston is at top dead center (TDC) of the compression stroke. (Until the counterweight contacts SST and stops.)
  18. Loosen the timing chain using the following procedure.
    1. Insert a suitable bolt (M6 X 1.0, length 25-35 mm {1.0-1.3 in}) into the engine front cover upper blind plug and tighten it until it contacts the chain tensioner arm, and then rotate it back one turn. (Set the bolt slightly away from the chain tensioner arm so that it does not contact it.)
      G13726599Courtesy of MAZDA MOTORS CORP.
    2. Using the cast hexagon on the exhaust camshaft, apply force counterclockwise to facilitate unlocking the chain tensioner ratchet.
      G06199770Courtesy of MAZDA MOTORS CORP.
    3. Using a Hex bit socket (2.5 mm {0.098 in}) or T15 Torx bit socket, unlock the chain tensioner ratchet so that it can be lifted up.
      G13726601Courtesy of MAZDA MOTORS CORP.
    4. Using the cast hexagon on the exhaust camshaft, apply force in the direction of the engine rotation to increase tension on the chain.
      G06150051Courtesy of MAZDA MOTORS CORP.
      NOTE:
      • The chain tensioner rack is compressed using the chain tension generated by applying force to the exhaust camshaft in the direction of the engine rotation.
      G13726603Courtesy of MAZDA MOTORS CORP.
    5. Screw in the bolt set in Step 1 approx. 5 mm {0.2 in} and secure the tensioner arm with the rack compressed.
    NOTE:
    • The racket has not been unlocked if the bolt cannot be pressed in approx. 5 mm {0.2 in}.
    G13726604Courtesy of MAZDA MOTORS CORP.
    • If the tensioner arm cannot be secured, return the bolt to its original position and repeat the procedure from Step  3.
  19. Fix the exhaust camshaft using a wrench on the cast hexagon, and loosen the camshaft sprocket bolt.
    G04859459Courtesy of MAZDA MOTORS CORP.
  20. Remove the exhaust camshaft sprocket bolt, exhaust camshaft sprocket, and washer as a single unit.
    CAUTION:
    • Perform the work carefully so that the washer does not drop out.
    G13726635Courtesy of MAZDA MOTORS CORP.
  21. Remove the OCV. (See OIL CONTROL VALVE (OCV) REMOVAL/INSTALLATION .)
  22. Loosen the camshaft cap bolts in two or three steps in the order shown in the figure and remove the camshaft cap.
    NOTE:
    • The camshaft caps are to be kept ordered for correct reassembly in their original positions. Do not mix the caps.
    Fig 2: Camshaft Caps Bolts Loosening Sequence
    G13726636Courtesy of MAZDA MOTORS CORP.
  23. Remove the variable valve timing actuator and the camshaft on the intake air side as a single unit.
  24. Remove the variable valve timing actuator.
    1. Mark the camshaft and variable valve timing actuator as shown in the figure to make sure they are installed in their original position.
      G13726637Courtesy of MAZDA MOTORS CORP.
      NOTE:
      • Do not add scratch marks to the camshaft thrust area.
    2. Secure the camshaft in a vise.
      G13726638Courtesy of MAZDA MOTORS CORP.
    3. Loosen the variable valve timing actuator tightening bolt.
  25. Install a new washer.
    G13726639Courtesy of MAZDA MOTORS CORP.
  26. Install the variable valve timing actuator.
    NOTE:
    • When the variable valve timing actuator is replaced with a new one, mark it in the same location as the old one.
    1. Secure the camshaft in a vise.
    2. Align the marks of the camshaft and variable valve timing actuator.
    3. Tighten variable valve timing actuator tightening bolt.

    Tightening torque 

    69-75 N.m {7.1-7.6 kgf.m, 51-55 ft.lbf}

    NOTE:
    • If the alignment marks on the variable valve timing actuator are not available, refer to the "TIMING CHAIN  ASSEMBLY" in the engine service information and perform the sprocket position alignment again.
  27. Verify that No. 1 cylinder is at TDC of the compression stroke. (Position counterweight contacts SST.)
  28. Apply the gear oil (SAE No. 90 or equivalent) to each journal of the cylinder head as shown in the figure.
    G06730555Courtesy of MAZDA MOTORS CORP.
  29. With No. 1 cylinder cam aligned at TDC of the compression stroke, install the variable valve timing actuator and the camshaft on the intake air side as a single unit.
  30. Apply the gear oil (SAE No. 90 or equivalent) to each journal of the camshaft as shown in the figure.
    G06730556Courtesy of MAZDA MOTORS CORP.
  31. Temporarily tighten the camshaft cap bolts evenly in 2-3 steps.
  32. Install the camshaft cap to the position of the marked number shown in the figure, tighten the camshaft cap bolts evenly in 2-3 rounds, and then tighten them in two steps in the order shown in the figure.
    Fig 3: Camshaft Caps Bolts Tightening Sequence
    G13726642Courtesy of MAZDA MOTORS CORP.

    Tightening procedure 

    Step 1: 5.0-9.0 N.m {51-91 kgf.cm, 45-79 in.lbf}

    Step 2: 14-17 N.m {1.5-1.7 kgf.m, 11-12 ft.lbf}

  33. Install the OCV. (See OIL CONTROL VALVE (OCV) REMOVAL/INSTALLATION .)
  34. Install the timing chain, exhaust camshaft sprocket bolt, exhaust camshaft sprocket, and a new washer as a single unit.
    CAUTION:
    • Install a washer to the fourth or fifth thread of the exhaust camshaft sprocket bolt being careful not to drop the washer.
    • Do not tighten the camshaft sprocket bolt at this stage. Verify the valve timing before performing the bolt tightening.
    G13726643Courtesy of MAZDA MOTORS CORP.
  35. Install the SST on the camshaft as shown in the figure.
    G13726613Courtesy of MAZDA MOTORS CORP.
  36. Remove the installation bolt for the engine front cover upper blind plug (M6 x 1.0 length 25-35mm {1.0-1.3 in}), and apply tension to the timing chain.
  37. Fix the exhaust camshaft using a wrench on the cast hexagon, and tighten the sprocket bolt.
    G06150062Courtesy of MAZDA MOTORS CORP.

    Tightening torque 

    69-75 N.m {7.1-7.6 kgf.m, 51-55 ft.lbf}

  38. Remove the SST from the camshaft.
  39. Remove the SST installed in the cylinder block lower blind plug hole.
  40. Rotate the crankshaft clockwise two turns and inspect the valve timing.
    • If not aligned, loosen the camshaft sprocket bolt and repeat the procedure from Step  35.
  41. Install the cylinder block lower blind plug.
    G13726615Courtesy of MAZDA MOTORS CORP.

    Tightening torque 

    18-22 N.m {1.9-2.2 kgf.m, 14-16 ft.lbf}

  42. Connect the drive shaft (RH) to joint shaft. (MTX) (See DRIVE SHAFT REMOVAL/INSTALLATION .)
  43. Apply the silicone sealant and install the engine front cover upper blind plug.
    G13726616Courtesy of MAZDA MOTORS CORP.
    CAUTION:
    • Install the engine front cover upper blind plug before the applied silicone sealant starts to harden.

    Tightening torque 

    8-11 N.m {82-117 kgf.cm, 71-101 in.lbf}

  44. Install a new engine front cover lower blind plug.
    G13726596Courtesy of MAZDA MOTORS CORP.

    Tightening torque 

    10-14 N.m {102-142 kgf.cm, 89-123 in.lbf}

  45. Install the drive belt. (See DRIVE BELT REMOVAL/INSTALLATION .)
  46. Install the aerodynamic under cover and splash shield as a single unit. (See AERODYNAMIC UNDER COVER REMOVAL/INSTALLATION .) (See SPLASH SHIELD REMOVAL/INSTALLATION .)
  47. Install the cylinder head cover. (See TIMING CHAIN REMOVAL/INSTALLATION .)
  48. Install the oil level gauge.
  49. Install the ventilation hose.
  50. Install the spark plugs. (See SPARK PLUG REMOVAL/INSTALLATION .)
  51. Install the ignition coils. (See IGNITION COIL REMOVAL/INSTALLATION .)
  52. Connect the wiring harness.
  53. Install the plug hole plate. (See PLUG HOLE PLATE REMOVAL/INSTALLATION .)
  54. Connect the negative battery cable.
  55. Install the battery cover. (See BATTERY REMOVAL/INSTALLATION .)