LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2014 >> MX-5 Miata Club, Standard Trans >> Repair and Diagnosis >> Engine Performance >> System >> Symptom Troubleshooting [Engine Control System] >> No. 6 Cranks Normally But Will Not Start

No. 6 Cranks Normally But Will Not Start

6  CRANKS NORMALLY BUT WILL NOT START 
DESCRIPTION 
  • The starter cranks engine at normal speed but the engine will not run.
  • Refer to symptom troubleshooting "NO. 5 ENGINE STALLS-AFTER START/AT IDLE " if this symptom appears after engine stall.
  • Fuel is in tank.
  • Battery is in normal condition.
POSSIBLE CAUSE 
  • No battery power supply to PCM
  • Air leakage from intake-air system
  • Open PCM ground or vehicle body ground
  • Improper operation of electronic throttle control system
  • EGR valve malfunction
  • No signal from CKP sensor due to sensor, related wire or incorrect installation
  • No signal from CMP sensor due to sensor, related wire or incorrect installation
  • Low engine compression
  • Engine overheating
  • Vacuum leakage
  • Erratic signal to ignition coil
  • Improper air/Fuel mixture ratio control
  • Poor fuel quality
  • PCV valve malfunction
  • Restriction in intake-air system
  • Restriction in exhaust system
  • Disconnected electrical connector
  • Open or short circuit in fuel pump body and related wiring harness
  • Inadequate fuel pressure
  • Fuel pump mechanical malfunction
  • Fuel leakage from injector
  • Fuel injector is clogged.
  • Purge solenoid valve malfunction
  • Spark plug malfunction
  • Ignition coil malfunction
  • Improper variable valve timing control system operation
  • Improper valve timing
  • Immobilizer system and/or circuit malfunction
  • Immobilizer system operating properly. (Ignition key is not registered).
  • Pressure regulator malfunction (built-in fuel pump unit)
    WARNING: The following troubleshooting flow chart contains the fuel system diagnosis and repair procedures. Read the following warnings before servicing the fuel system:
    • Fuel vapor is hazardous. It can easily ignite, causing serious injury and damage. Always keep sparks and flames away from fuel.
    • Fuel line spills and leakage are dangerous. Fuel can ignite and cause serious injuries or death and damage. Fuel can also irritate skin and eyes. To prevent this, always complete "BEFORE SERVICE PRECAUTION " and "AFTER SERVICE PRECAUTION ".
    CAUTION:
    • Disconnecting/connecting quick release connector without cleaning it may cause damage to fuel pipe and quick release connector. Always clean quick release connector joint area before disconnecting/connecting, and make sure that it is free of foreign material.
DIAGNOSTIC PROCEDURE

STEP INSPECTION RESULTS ACTION
1 Do any of the following conditions appear?
  • Engine does not completely start.
  • DTC P1260 is displayed.
Yes Both conditions appear: 
  • Go to Step 3.
No Either or other condition appears: 
  • Go to the next step.
2 Does the engine stall after approx. 2 s  from when it is started? Yes Go to the next step.
No Immobilizer system is normal.
Go to Step 8.
3 Is the coil antenna connector securely connected to the coil antenna? Yes Go to the next step.
No Connect the coil antenna connector securely.
Return to Step 2.
4 Does the security light flash? Yes Go to the next step.
No Inspect the following:
  • Wiring harnesses and connectors from keyless control module terminal 3F and instrument cluster terminal 2F
  • Instrument cluster

    (See INSTRUMENT CLUSTER INSPECTION ).


Repair or replace the malfunctioning part according to the inspection results.
5 Retrieve the DTC for the immobilizer system.
(See DTC INSPECTION [IMMOBILIZER SYSTEM (KEYLESS ENTRY SYSTEM)] ).
(See DTC INSPECTION [ADVANCED KEYLESS AND START SYSTEM] ).
Is there any DTC present?
Yes Go to the appropriate DTC inspection.
(See DTC TABLE ).
(See DTC TABLE [INSTRUMENT CLUSTER] ).
(See DTC INSPECTION [IMMOBILIZER SYSTEM (ADVANCED KEYLESS AND START SYSTEM)] ).
No Go to the next step.
6 Inspect for the following wiring harnesses and connectors:
With advanced keyless and start system: 
  • Between coil antenna terminal A and keyless control module terminal 3Y
  • Between coil antenna terminal B and keyless control module terminal 3AA
  • Between keyless control module terminal 4A and instrument cluster terminal 2Q
  • Between keyless control module terminal 4C and instrument cluster terminal 2S

Without advanced keyless and start system: 
  • Between coil antenna terminal A and instrument cluster terminal 2S
  • Between coil antenna terminal B and instrument cluster terminal 2Q

Is there any malfunction?
Yes Repair or replace the suspected wiring harness and connector.
No Go to the next step.
7 Inspect the following wiring harnesses and connectors:
  • Between PCM terminal 1AM and instrument cluster terminal 1J
  • Between PCM terminal 1 Al and instrument cluster terminal 1L

Is there any malfunction?
Yes Repair or replace the suspected wiring harness and connector.
No Go to the next step.
8 Verify the following:
  • Vacuum connection
  • External fuel shut off or accessory (such as kill switch, alarm)
  • Fuel quality: proper octane, contamination, winter/summer blend
  • No air leakage from intake-air system
  • Intake-air system restriction (such as air cleaner element, fresh air duct)
  • Proper sealing of intake manifold and components attached to intake manifold: EGR valve
  • Ignition wiring
  • Electrical connections
  • Fuses
  • Smooth operation of throttle valve

Are all items normal?
Yes Go to the next step.
No Service if necessary.
Repeat Step 8.
9 Turn the ignition switch to the ON position (Engine off).
Retrieve any DTCs.
Are there any DTCs displayed?
Yes DTC is displayed: 
  • Go to the appropriate DTC inspection.

    (See DTC TABLE ).


Communication error message is displayed: 
  • Inspect for the following:
    • Open circuit in wiring harness between main relay and PCM terminal 1AW or 1BE
    • Open main relay ground circuit
    • Open or short circuit in wiring harness between DLC and PCM terminal 1AM or 1AI
    • Main relay is stuck open.
    • Open or poor ground circuit (PCM terminal 1AZ, 1BB, 1BD, 1BH)
    • Poor connection of vehicle body ground
No Go to the next step.
10 Access the APP1 and APP2 PIDs. Crank the engine with accelerator pedal released.
Are the APP1 and APP2 PIDs indicating that the accelerator pedal is in the released position?
Yes Go to the next step.
No Inspect for the following:
  • APP sensor

    (See ACCELERATOR PEDAL POSITION (APP) SENSOR INSPECTION ).

  • Wiring harnesses and connectors for following:
    • PCM terminal 1AJ-APP sensor terminal A
    • PCM terminal 1AV-APP sensor terminal B
    • PCM terminal 1AP-APP sensor terminal C
    • PCM terminal 1AL-APP sensor terminal D
    • PCM terminal 1AS-APP sensor terminal E
    • PCM terminal 1AO-APP sensor terminal F
11 Access the TP PID. Crank the engine with accelerator pedal released.
Are the TP PID indicates the closed throttle position?
Yes Go to the next step.
No Inspect for the following:
  • TP sensor

    (See THROTTLE POSITION (TP) SENSOR INSPECTION ).

  • Wiring harnesses and connectors for following:
    • PCM terminal 2AK-TP sensor terminal F
    • PCM terminal 2AO-TP sensor terminal E
    • PCM terminal 2AP-TP sensor terminal C
    • PCM terminal 2AL-TP sensor terminal D
12 Does the engine start with the throttle valve closed? Yes Go to Step 28.
No Go to the next step.
13 Will the engine start and run smoothly at part throttle? Yes Perform the Electronic Throttle Control System Inspection.
(See ENGINE CONTROL SYSTEM OPERATION INSPECTION ).
No Go to the next step.
14 Access the RPM PID.
Is the RPM PID indicating the engine speed when cranking the engine?
Yes Go to the next step.
No Inspect for the following:
  • Open or short circuit in CKP sensor
  • Open or short circuit in wiring harness between CKP sensor terminal A and PCM terminal 2AB
  • Open or short circuit in wiring harness between CKP sensor terminal B and PCM terminal 2W
  • Open or short circuit in wiring harness between CKP sensor terminal C and PCM terminal 2AQ
  • Open or short circuit in CKP sensor wiring harnesses

If CKP sensor and wiring harness are normal, go to the next step.
15 Visually inspect the CKP sensor and teeth of crankshaft pulley.
Are CKP sensor and teeth of crankshaft pulley normal?
Yes Go to the next step.
No Repair or replace the malfunctioning part according to the inspection results.
16 Inspect the ignition coil related wiring harness condition (intermittent open or short circuit) for all cylinders.
Are wiring harness conditions normal?
Yes Go to the next step.
No Repair or replace the suspected wiring harness.
17 Perform the Spark Test.
(See ENGINE CONTROL SYSTEM OPERATION INSPECTION ).
Is the strong blue spark visible at each cylinder?
Yes Go to the next step.
No Repair or replace the malfunctioning part according to spark test result.
18 Verify the spark plug conditions when the spark plug removed in Step 17.
Is the spark plug wet, covered with carbon or grayish white?
Yes Spark plug is wet or covered with carbon: 
  • Inspect for fuel leakage from injector.

Spark plug is grayish white: 
  • Inspect the fuel injector for clogging.
No Install the spark plugs on original cylinders.
Go to the next step.
19 Visually inspect the exhaust system part.
Is there any deformed exhaust system part?
Yes Repair or replace the malfunctioning part according to the inspection results.
No Go to the next step.
20 Install the fuel pressure gauge between the fuel pipe and the fuel distributor.
Turn the ignition switch to the ON position (Engine off).
Turn to on and off the fuel pump using the M-MDS simulation function "FP".
Is the fuel line pressure correct when fuel pump is turned on/off five times?
(See FUEL LINE PRESSURE INSPECTION ).
Yes Go to the next step.
No Zero or low: 
  • Inspect the fuel pump relay and fuel pump circuit.
  • Inspect the fuel line for clogging.
  • If there is no malfunction, replace the fuel pump unit.

    (See FUEL PUMP UNIT REMOVAL/INSTALLATION ).


High: 
21 Visually inspect the fuel injector O-ring and fuel line for fuel leakage.
Service if necessary.
Is the fuel line pressure held after the ignition switch is turned off?
(See FUEL LINE PRESSURE INSPECTION ).
Yes Go to the next step.
No Inspect the fuel injector.
(See FUEL INJECTOR INSPECTION ).
If the fuel injector is normal, replace the fuel pump unit.
(See FUEL PUMP UNIT REMOVAL/INSTALLATION ).
22 Disconnect the vacuum hose between the purge solenoid valve and the intake manifold from purge solenoid valve side.
Plug opening end of vacuum hose.
Start the engine.
Is starting condition improved?
Yes Inspect if the purge solenoid valve is stuck open mechanically.
Inspect the EVAP control system.
No Go to the next step.
23 Is the air leakage felt or heard at intake-air system components while racing engine to higher speed? Yes Repair or replace the malfunctioning part according to the inspection results.
No Go to the next step.
24 Inspect the engine condition while tapping EGR valve housing.
Is the engine condition improved?
Yes Replace the EGR valve.
(See EGR VALVE REMOVAL/INSTALLATION ).
No Go to the next step.
25 Perform the Variable Valve Timing Control System Operation Inspection.
(See ENGINE CONTROL SYSTEM OPERATION INSPECTION ).
Does the variable valve timing control function properly?
Yes Go to the next step.
No Repair or replace the malfunctioning part according to the inspection results.
26 Is the engine compression correct?
(See COMPRESSION INSPECTION ).
Yes Go to the next step.
No Inspect for causes.
27 Inspect the PCV valve.
(See POSITIVE CRANKCASE VENTILATION (PCV) VALVE INSPECTION ).
Is there any malfunction?
Yes Replace the PCV valve.
(See POSITIVE CRANKCASE VENTILATION (PCV) VALVE REMOVAL/INSTALLATION ).
No Inspect the valve timing.
(See VARIABLE VALVE TIMING ACTUATOR INSPECTION
28
  • Verify test results.
    • If normal, return to diagnostic index to service any additional symptoms.

      (See SYMPTOM DIAGNOSTIC INDEX ).

    • If malfunction remains, inspect related Service Bulletins and/or On-line Repair Information and perform repair or diagnosis.
      • If vehicle is repaired, troubleshooting completed.
      • If vehicle is not repaired or additional diagnostic information is not available, replace the PCM.

        (See PCM REMOVAL/INSTALLATION ).