LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2014 >> MX-5 Miata Club, Standard Trans >> Repair and Diagnosis >> Engine Performance >> System >> Symptom Troubleshooting [Engine Control System] >> No. 15 Emission Compliance

No. 15 Emission Compliance

15  EMISSION COMPLIANCE 
DESCRIPTION 
  • Fails emissions test.
POSSIBLE CAUSE 
  • Vacuum lines leakage or blockage
  • Cooling system malfunction
  • Spark plug malfunction
  • Leakage from intake manifold
  • Erratic or no signal from CMP sensor
  • Inadequate fuel pressure
  • PCV valve malfunction or incorrect valve installation
  • EGR valve malfunction
  • Exhaust system clogging
  • Fuel tank ventilation system malfunction
  • Fuel-filler cap malfunction
  • Charcoal canister damage
  • Air cleaner element clogging or restriction
  • Throttle body malfunction
  • Erratic signal to ignition coil
  • Improper air/fuel mixture ratio control operation
  • Bend or open circuit A/F sensor or HO2S wiring harness
  • Catalyst converter malfunction
  • Engine internal parts malfunction
  • Excessive carbon is built up in combustion chamber
  • Improper engine compression
  • Improper valve timing
    WARNING: The following troubleshooting flow chart contains fuel system diagnosis and repair procedures. Read following warnings before servicing fuel system:
    • Fuel vapor is hazardous. It can easily ignite, causing serious injury and damage. Always keep sparks and flames away from fuel.
    • Fuel line spills and leakage are dangerous. Fuel can ignite and cause serious injuries or death and damage. Fuel can also irritate skin and eyes. To prevent this, always complete "BEFORE SERVICE PRECAUTION " and "AFTER SERVICE PRECAUTION ".
    CAUTION:
    • Disconnecting/connecting quick release connector without cleaning it may cause damage to fuel pipe and quick release connector. Always clean quick release connector joint area before disconnecting/connecting, and make sure that it is free of foreign material.
DIAGNOSTIC PROCEDURE

STEP INSPECTION RESULTS ACTION
1 Inspect for the following:
  • Vacuum lines for leakage or blockage
  • Electrical connections
  • Proper maintenance schedule followed
  • Intake-air system and air cleaner element concerns: obstructions, leakage or dirtiness

Are all items normal?
Yes Go to the next step.
No Service if necessary.
Repeat Step 1.
2 Turn the ignition switch to the ON position (Engine off).
Retrieve any DTCs.
Are there any DTCs displayed?
Yes Go to appropriate DTC inspection.
(See DTC TABLE ).
No Go to the next step.
3 Is any other driveability concern present? Yes Go to the appropriate system symptom troubleshooting article.
No Go to the next step.
4 Access the ECT PID.
Warm up the engine and idle it.
Verify the ECT PID is correct.
Is the ECT PID correct?
(See PCM INSPECTION ).
Yes Go to the next step.
No Inspect for coolant leakage, cooling fan and condenser fan operation or thermostat operation.
5 Inspect the fuel-filler cap.
(See FUEL-FILLER CAP INSPECTION ).
Is there any leakage at fuel-filler cap?
Yes Replace the fuel-filler cap.
No Go to the next step.
6 Inspect the A/F sensor.
(See AIR FUEL RATIO (A/F) SENSOR INSPECTION ).
Is the A/F sensor normal?
Yes Go to the next step.
No Replace the A/F sensor.
(See AIR FUEL RATIO (A/F) SENSOR REMOVAL/INSTALLATION ).
7 Perform the Spark Test.
(See ENGINE CONTROL SYSTEM OPERATION INSPECTION ).
Is the strong blue spark visible at each cylinder?
Yes Go to the next step.
No Repair or replace the malfunctioning part according to spark test result.
8 Install the fuel pressure gauge between the fuel pipe and the fuel distributor.
Start the engine and idle it.
Measure the fuel line pressure during idle.
Is the fuel line pressure correct during idle?
(See FUEL LINE PRESSURE INSPECTION ).
Yes Go to the next step.
No Low: 

High: 
9 Inspect for fuel saturation inside charcoal canister.
Is the excess amount of liquid fuel present in canister?
Yes Replace the charcoal canister.
No Inspect the fuel tank vent system, then go to the next step.
(See FUEL TANK INSPECTION ).
10 Visually inspect the exhaust system part.
Is there any deformed exhaust system part?
Yes Repair or replace the malfunctioning part according to the inspection results.
No Go to the next step.
11 Inspect the three-way catalytic converter.
(See EXHAUST SYSTEM INSPECTION ).
Is the three-way catalytic converter normal?
Yes Go to the next step.
No Replace the three-way catalytic converter.
12 Perform EGR control system inspection.
(See ENGINE CONTROL SYSTEM OPERATION INSPECTION ).
Is EGR system normal?
Yes Go to the next step.
No Repair or replace the malfunctioning part according to the inspection results.
13 Is the engine compression correct?
(See COMPRESSION INSPECTION ).
Yes Go to the next step.
No Inspect for cause.
14 Inspect the PCV valve.
(See POSITIVE CRANKCASE VENTILATION (PCV) VALVE INSPECTION ).
Is there any malfunction?
Yes Replace the PCV valve.
(See POSITIVE CRANKCASE VENTILATION (PCV) VALVE REMOVAL/INSTALLATION ).
No Inspect the valve timing.
(See VARIABLE VALVE TIMING ACTUATOR INSPECTION
15
  • Verify test results.
    • If normal, return to diagnostic index to service any additional symptoms.

      (See SYMPTOM DIAGNOSTIC INDEX ).

    • If malfunction remains, inspect related Service Bulletins and/or On-line Repair Information and perform repair or diagnosis.
      • If vehicle is repaired, troubleshooting completed.
      • If vehicle is not repaired or additional diagnostic information is not available, replace the PCM.

        (See PCM REMOVAL/INSTALLATION ).