LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2014 >> MX-5 Miata Club, Standard Trans >> Repair and Diagnosis >> Engine Performance >> System >> Symptom Troubleshooting [Engine Control System] >> No. 10 Low Idle/Stalls During Deceleration

No. 10 Low Idle/Stalls During Deceleration

10  LOW IDLE/STALLS DURING DECELERATION 
DESCRIPTION 
  • The engine stops unexpectedly at the beginning of deceleration or recovery from deceleration.
POSSIBLE CAUSE 
  • Vacuum leakage
  • Improper operation of electronic throttle control system
  • Air leakage from intake-air system
  • Improper air/fuel mixture ratio control
  • EVAP control system malfunction
  • APP sensor or related circuit malfunction
  • TP sensor or related circuit malfunction
  • MAF sensor or related circuit malfunction
  • Brake switch or related circuit malfunction
  • Neutral/CPP switch or related circuit malfunction (MT)
  • TR switch or related circuit malfunction (AT)
  • Improper A/C magnetic clutch operation
DIAGNOSTIC PROCEDURE

STEP INSPECTION RESULTS ACTION
1 Does the engine idle roughly? Yes Go to the symptom troubleshooting "No. 8 Engine runs rough/rolling idle".
(See NO. 8 ENGINE RUNS ROUGH/ROLLING IDLE ).
No Go to the next step.
2 Turn off the A/C switch and fan switch.
Does the A/C magnetic clutch engage?
Yes Go to the symptom troubleshooting "No. 24 A/C is always on or A/C compressor runs continuously."
(See NO. 24 A/C IS ALWAYS ON OR A/C COMPRESSOR RUNS CONTINUOUSLY ).
No Go to the next step.
3 Verify the following:
  • Proper routing of and no damage to vacuum lines
  • No air leakage from intake-air system

Are ail items normal?
Yes Go to the next step.
No Service if necessary.
Repeat Step 3.
4 Turn the ignition switch to the ON position (Engine off).
Retrieve any DTCs.
Are there any DTCs displayed?
Yes Go to the appropriate DTC inspection.
(See DTC TABLE ).
No Go to the next step.
5 Perform the Electronic Throttle Control System Inspection.
(See ENGINE CONTROL SYSTEM OPERATION INSPECTION ).
Does the electronic throttle control system function properly?
Yes Go to the next step.
No Repair or replace the malfunctioning part according to electronic the inspection results.
6
CAUTION:
  • While performing this step, always operate the vehicle in a safe and lawful manner.
Disconnect the vacuum hose between the purge solenoid valve and the intake manifold from purge solenoid valve side.Plug opening end of vacuum hose.Drive the vehicle.Does the engine condition improve?
Yes Inspect the EVAP control system.
No Go to the next step.
7
CAUTION:
  • While performing this step, always operate the vehicle in a safe and lawful manner.
  • When the M-MDS is used to observe monitor system status while driving, be sure to have another technician with you, or record the data in the M-MDS using the PID/DATA MONITOR AND RECORD capturing function and inspect later.
Access the APP1, APP2, TP, MAF and VSS PIDs.Monitor each PID while driving the vehicle.Are the PIDs values normal?(See PCM INSPECTION ).
Yes Go to the next step.
No APP1, APP2 PIDs are not normal: 

TP PID is not normal: 

MAF PID is not normal: 

VSS PID is not normal: 
8 Access and monitor the following PCM and TCM PIDs:
PCM: 
  • BOO
  • CPP(MT)
  • CPP/PNP(MT)

TCM: 
  • TR

Are the PIDs values normal?
(See PCM INSPECTION ).
(See PID/DATA MONITOR INSPECTION ).
Yes Go to the next step.
No If the BOO PID is not normal: 
  • Inspect the brake switch, and related wiring harness for vibration or intermittent open/short circuit.

    (See BRAKE SWITCH INSPECTION ).


If the CPP PID is not normal: 

If the CPP/PNP PID is not normal: 
  • Inspect the neutral switch and related wiring harness for vibration or intermittent open/short circuit.

    (See NEUTRAL SWITCH INSPECTION ).


If the TR PID is not normal: 
9
  • Verify test results.
    • If normal, return to diagnostic index to service any additional symptoms.

      (See SYMPTOM DIAGNOSTIC INDEX ).

    • If malfunction remains, inspect related Service Bulletins and/or On-line Repair Information and perform repair or diagnosis.
      • If vehicle is repaired, troubleshooting completed.
      • If vehicle is not repaired or additional diagnostic information is not available, replace the PCM.

        (See PCM REMOVAL/INSTALLATION ).