LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2013 >> 6 i Touring Plus >> Repair and Diagnosis >> Engine Performance >> System >> Symptom Troubleshooting [Engine Control System MZR 2.5] >> No.14 Poor Fuel Economy >> Diagnostic Procedure

Diagnostic Procedure

STEP INSPECTION RESULTS ACTION
1 INSPECT RELATED PART CONDITION 
  • Inspect for the following:
    • Air cleaner element for contamination
    • ATF level (ATX)
    • Fuel quality
    • Coolant level
    • Brake dragging
    • Clutch slippage (MTX)
    • Tire pressure
  • Are all the items normal?
Yes Go to the next step.
No Repair or replace the malfunctioning part according to the inspection results.
Repeat Step 1.
2 VERIFY PCM DTC 
Yes Go to the appropriate DTC inspection.
(See DTC TABLE .)
No Go to the next step.
3 INSPECT COOLING SYSTEM FOR MALFUNCTION 
  • Is any cooling system concern (overheating, runs cold) present?
Yes Go to the symptom troubleshooting "NO.17 COOLING SYSTEM CONCERNS-OVERHEATING" or "NO.18 COOLING SYSTEM CONCERNS-RUNS COLD".
(See NO.17 COOLING SYSTEM CONCERNS-OVERHEATING .)
(See NO.18 COOLING SYSTEM CONCERNS-RUNS COLD .)
No Go to the next step.
4 INSPECT COOLING FAN CONTROL SYSTEM OPERATION 
Yes Go to the next step.
No Repair or replace the malfunctioning part according to the inspection results.
5 INSPECT IGNITION SYSTEM OPERATION 
Yes Go to the next step.
No Repair or replace the malfunctioning part according to the inspection results.
6 INSPECT FUEL LINE PRESSURE 
Yes Go to the next step.
No Zero or low:
  • Inspect the following:

High:
7 INSPECT VARIABLE TUMBLE CONTROL OPERATION 
Yes Go to the next step.
No Repair or replace the malfunctioning part according to the inspection results.
8 INSPECT VARIABLE VALVE TIMING CONTROL SYSTEM OPERATION 
Yes Go to the next step.
No Repair or replace the malfunctioning part according to the inspection results.
9 INSPECT VARIABLE INTAKE AIR CONTROL OPERATION 
Yes Go to the next step.
No Repair or replace the malfunctioning part according to the inspection results.
10 INSPECT DEFORMED IN EXHAUST SYSTEM 
  • Visually inspect the exhaust system part.
  • Is there any deformed exhaust system part?
Yes Repair or replace the malfunctioning part according to the inspection results.
No Go to the next step.
11 INSPECT MAF SENSOR FOR CONTAMINATION 
  • Inspect the MAF sensor for contamination.
  • Is there any contamination?
Yes Replace the MAF/IAT sensor.
(See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION .)
No Go to the next step.
12 INSPECT ENGINE COMPRESSION 
Yes Go to the next step.
No Inspect for cause.
Repair or replace the malfunctioning part according to the inspection results.
13 INSPECT IF MALFUNCTION CAUSE IS PCV VALVE OR VALVE TIMING 
Yes Inspect the valve timing.
Repair or replace the malfunctioning part according to the inspection results.
No Replace the PCV valve and the oil separator as a single unit, then go to the next step.
(See POSITIVE CRANKCASE VENTILATION (PCV) VALVE REMOVAL/INSTALLATION .)
14
  • Verify test results.
    • If normal, return to diagnostic index to service any additional symptoms.

      (See SYMPTOM DIAGNOSTIC INDEX .)

    • If malfunction remains, inspect related Service Bulletins and/or On-line Repair Information and perform repair or diagnosis.
      • If vehicle is repaired, troubleshooting completed.
      • If vehicle is not repaired or additional diagnostic information is not available, reprogram the PCM if a later calibration is available. Retest.