LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2013 >> 6 i Touring Plus >> Repair and Diagnosis >> Engine Performance >> System >> Symptom Troubleshooting [Engine Control System MZR 2.5] >> No.12 Lack/Loss Of Power-Acceleration/Cruise >> Diagnostic Procedure

Diagnostic Procedure

STEP INSPECTION RESULTS ACTION
1 CONFIRM DRIVE-BY-WIRE CONTROL SYSTEM OPERATES WITH BRAKE OVERRIDE SYSTEM 
Yes Go to the applicable DTC inspection. (Drive-by-wire control system operates with brake override system.)
(See DTC P2299:00 .)
No Go to the next step.
2 INSPECT RELATED PART CONDITION 
  • Verify the following:
    • Vacuum connection
    • Restriction in the intake air system (such as the air cleaner element, fresh air duct)
    • No air leakage from the intake air system
    • No restriction of the intake air system
    • Proper sealing of the intake manifold and components attached to the intake manifold: such as the EGR valve
    • Fuel quality (such as proper octane, contamination, winter/summer blend)
  • Are all the items normal?
Yes Go to the next step.
No Repair or replace the malfunctioning part according to the inspection results.
Repeat Step 2.
3 VERIFY PCM DTC 
Yes Go to the appropriate DTC inspection.
(See DTC TABLE .)
No Go to the next step.
4 VERIFY IF MALFUNCTION CAUSE IS OVERHEATING 
  • Is the engine overheating?
Yes Go to the symptom troubleshooting "NO.17 COOLING SYSTEM CONCERNS-OVERHEATING".
(See NO.17 COOLING SYSTEM CONCERNS-OVERHEATING .)
No Go to the next step.
5 VERIFY CURRENT INPUT SIGNAL STATUS 
CAUTION:
  • While performing this step, always operate the vehicle in a safe and lawful manner.
  • When the M-MDS is used to observe monitor system status while driving, be sure to have another technician with you, or record the data in the M-MDS using the PID/DATA MONITOR AND RECORD capturing function and inspect later.
  • Access the following PCM PIDs using the M-MDS.

    (See ON-BOARD DIAGNOSTIC TEST .)

    • APP1
    • APP2
    • RPM
    • MAF
    • TP REL
    • IAT
    • VSS
  • Do the PIDs indicate correct values under the trouble condition?

    (See PCM INSPECTION .)

Yes Go to the next step.
No APP1, APP2 PIDs are not specified:

TP REL PID is not specified:

RPM PID is not specified:

MAF PID is not specified:

IAT PID is not specified:

VSS PID is not specified:

Repair or replace the malfunctioning part according to the inspection result.
6 VISUALLY INSPECT CKP SENSOR AND PULSE WHEEL 
Yes Go to the next step.
No Repair or replace the malfunctioning part according to the inspection result.
7 VERIFY SPARK PLUG CONDITION 
  • Verify the spark plug conditions when the spark plug removed in Step 8.

    (See SPARK PLUG INSPECTION .)

  • Is spark plug wet, covered with carbon or grayish white?
Yes Spark plug is wet or covered with carbon:
  • Inspect for fuel leakage from fuel injector.

Spark plug is grayish white:
  • Inspect the fuel injector for clogging.

Repair or replace the malfunctioning part according to the inspection results.
No Install the spark plugs on original cylinders.
Go to the next step.
8 INSPECT THROTTLE BODY FOR CLOGGING 
Yes Clean the throttle valve.
No Go to the next step.
9 INSPECT DRIVE-BY-WIRE CONTROL SYSTEM OPERATION 
Yes Go to the next step.
No Repair or replace the malfunctioning part according to the inspection results.
10 INSPECT DEFORMED IN EXHAUST SYSTEM 
  • Visually inspect the exhaust system part.
  • Is there any deformed exhaust system part?
Yes Repair or replace the malfunctioning part according to the inspection results.
No Go to the next step.
11 INSPECT FUEL LINE PRESSURE 
Yes Go to the next step.
No Zero or low:
  • Inspect the following:

High:
12 INSPECT VARIABLE TUMBLE CONTROL OPERATION 
Yes Go to the next step.
No Repair or replace the malfunctioning part according to the inspection results.
13 INSPECT VARIABLE INTAKE AIR CONTROL OPERATION 
Yes Go to the next step.
No Repair or replace the malfunctioning part according to the inspection results.
14 DETERMINE IF MALFUNCTION CAUSE IS A/C SYSTEM OR OTHER 
NOTE:
  • The following test is for stall concerns with the A/C on. If other symptoms exist, go to the next step.
  • Connect the pressure gauges to the A/C low side and high side pressure lines.
  • Turn the A/C on and measure the low side and high side pressures.
  • Are the pressures within the specifications?

    (See REFRIGERANT PRESSURE CHECK .)

Yes Go to the next step.
No If the A/C is always on:

For other symptoms:
  • Inspect the following:
    • Refrigerant charging amount
    • Cooling fan operation
  • Repair or replace the malfunctioning part according to the inspection results.
15 INSPECT A/C CUT-OFF CONTROL SYSTEM OPERATION 
Yes Go to the next step.
No Inspect the A/C cut-off system components.
Repair or replace the malfunctioning part according to the inspection results.
16 DETERMINE IF MALFUNCTION CAUSE IS EVAP CONTROL SYSTEM OR OTHER 
CAUTION:
  • While performing this step, always operate the vehicle in a safe and lawful manner.
  • Disconnect the vacuum hose between purge solenoid valve and intake manifold from the purge solenoid valve side.
  • Plug the open end of the vacuum hose.
  • Drive the vehicle.
  • Does the engine condition improve?
Yes Inspect the following:
  • If the purge solenoid valve is stuck open.
  • EVAP control system

Repair or replace the malfunctioning part according to the inspection results.
No Go to the next step.
17 VISUALLY INSPECT CMP SENSOR AND PULSE WHEEL 
Yes Go to the next step.
No Repair or replace the malfunctioning part according to the inspection results.
18 INSPECT EGR VALVE OPERATION 
Yes Go to the next step.
No Repair or replace the malfunctioning part according to the inspection results.
19 INSPECT VARIABLE VALVE TIMING CONTROL SYSTEM OPERATION 
Yes Go to the next step.
No Repair or replace the malfunctioning part according to the inspection results.
20 INSPECT ENGINE COMPRESSION 
Yes Go to the next step.
No Inspect for cause.
Repair or replace the malfunctioning part according to the inspection results.
21 INSPECT IF MALFUNCTION CAUSE IS PCV VALVE OR VALVE TIMING 
Yes Inspect the following:
  • Valve timing
  • Internal transaxle part (ATX)
  • Brake system for dragging

Repair or replace the malfunctioning part according to the inspection results.
No Replace the PCV valve and the oil separator as a single unit, then go to the next step.
(See POSITIVE CRANKCASE VENTILATION (PCV) VALVE REMOVAL/INSTALLATION .)
22
  • Verify test results.
    • If normal, return to diagnostic index to service any additional symptoms.

      (See SYMPTOM DIAGNOSTIC INDEX .)

    • If malfunction remains, inspect related Service Bulletins and/or On-line Repair Information and perform repair or diagnosis.
      • If vehicle is repaired, troubleshooting completed.
      • If vehicle is not repaired or additional diagnostic information is not available, reprogram the PCM if a later calibration is available. Retest.