LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2011 >> Tribute i Touring, FWD >> Repair and Diagnosis >> Transmission >> Automatic Trans >> Symptom Troubleshooting [Transaxle] >> Pinpoint Test 4: Transmission Range (Tr) Sensor >> Notes

Pinpoint Test 4: Transmission Range (Tr) Sensor: Notes

NOTE:
  • Refer to the transaxle connector illustrations and solenoid body leadframe internal wiring diagrams preceding these pinpoint tests. See TRANSAXLE CONNECTOR LAYOUTS  .
NOTE:
  • TR codes may be a result of a bad common power and ground shared between the TR sensor, OSS sensor and the TSS sensor.
DIAGNOSTIC PROCEDURE

PINPOINT TEST 4 TRANSMISSION RANGE (TR) SENSOR
STEP INSPECTION ACTION
1 VERIFY DTCs
  • Key in OFF position.
  • Select PARK
  • Key in START position
  • Carry out the OBD Test. DTCs P0706, P0707 and P0708 cannot be set by an incorrectly adjusted selector lever cable.
  • Are only TR DTC codes present? 
Yes GO to step 3.
No GO to the next step.
2 VERIFY SELECTOR LEVER CABLE/LINKAGE ADJUSTMENT
  • Disconnect the selector lever cable end from the manual control lever and release the lock tab.
  • Place the transaxle manual control lever in the D position.
  • Place the selector lever in the D position.
  • Reconnect the selector lever cable/linkage and lock the selector lever cable end lock tab.
  • Verify that the selector lever cable/linkage is correctly adjusted. See SELECTOR LEVER CABLE ADJUSTMENT .
G06157632

  • Is the selector lever cable/linkage correctly adjusted? 
Yes GO to the next step.
No ADJUST the selector lever cable/linkage. GO to step 4.
3 CHECK THE ELECTRICAL SIGNAL OPERATION
  • Select PARK position.
  • Disconnect: PCM transaxle 0140-175t.
  • Disconnect: Transaxle vehicle harness 0140-131 (2.5L), 0140-231 (3.0L).
  • Use a mirror to inspect both ends of the connectors for damaged or pushed-out pins, corrosion, loose wires and missing or damaged seals.
  • Is there damage to the connectors, pins or harness? 
Yes REPAIR as required. CLEAR DTCs and RERUN the OBD tests.
No GO to the next step.
4 CHECK ELECTRICAL SYSTEM OPERATION (TR and PCM)
  • Key in OFF position.
  • Connect the diagnostic tool.
  • Connect transaxle harness 0140-175t
  • Connect transaxle vehicle harness 0140-131 (2.5L), 0140-231 (3.0L).
  • Key in ON position.
  • Enter the following diagnostic mode on the diagnostic tool: TR PIDS TR DC and TR_FREG
  • Move the selector lever into each gear and stop.
  • Observe the following PIDs; TR PIDS TF_DC and TR_FREQ while wiggling harness or driving the vehicle.
  • Monitor PID: TR_FREQ.
  • Compare the PID: TR_DC to the TR position using the Selector Lever Position and Range (% Duty Cycle) chart at the end of this pinpoint test.
  • Is PID TR_FREQ between 100 to 150 Hz? 
  • Is PID TR_DC in range? 
  • Do the PIDs TR_DC and TF_FREQ remain steady when the harness is wiggled or the vehicle driven? 
Yes The concern is not in the TR sensor system. See DIAGNOSIS BY SYMPTOM  .
No If the PIDs change when wiggling the harness or driving the vehicle, the problem may be intermittent. GO to the next step.
5 CHECK THE TRANSAXLE VEHICLE HARNESS FOR AN OPEN
  • Disconnect PCM transaxle harness 0140-175t
  • Disconnect transaxle vehicle harness 0140-131 (2.5L), 0140-231 (3.0L).
  • Measure the resistance for the TR sensor circuits between the transaxle vehicle harness 0140-131 (2.5L), 0140-231 (3.0L) and the PCM transaxle harness 0140-175t using the Transmission Range Sensor Circuit, Transaxle Vehicle Harness and PCM chart at the end of this pinpoint test.
  • Is the resistance less than 5 ohms? 
Yes GO to the next step.
No REPAIR the circuit. CONNECT all components. TEST the system for normal operation.
6 CHECK THE TRANSAXLE VEHICLE HARNESS FOR A SHORT TO GROUND
  • Disconnect transaxle vehicle harness 0140-131 (2.5L), 0140-231 (3.0L)
  • Measure the resistance for the TR sensor circuits between the transaxle vehicle harness 0140-131 (2.5L), 0140-231 (3.0L) and ground using the Transmission Range Sensor Circuit, Transaxle Vehicle Harness and Ground chart at the end of this pinpoint test.
  • Are all resistances greater than 10,000 ohms? 
Yes GO to the next step.
No REPAIR shorted circuit(s). RECONNECT all components. TEST the system for normal operation.
7 CHECK THE TRANSAXLE VEHICLE HARNESS FOR A SHORT TO POWER
  • Measure the voltage for the TR sensor circuits between the transaxle vehicle harness 0140-131 (2.5L), 0140-231 (3.0L) and ground using the Transmission Range Sensor Circuit, Transaxle Vehicle Harness and Ground chart at the end of this pinpoint test.
  • Is any voltage present? 
Yes REPAIR shorted circuit(s). RECONNECT all components. TEST the system for normal operation.
No GO to the next step.
8 CHECK FOR A SHORT BETWEEN TR/PCM INPUT SIGNAL CIRCUITS
  • Measure the resistance between TR sensor circuits at the transaxle vehicle harness 0140-131 (2.5L), 0140-231 (3.0L) using the Transaxle Vehicle Harness, TR Sensor Circuit and Transaxle Vehicle Harness chart at the end of this pinpoint test.
  • Are all resistances greater than 10,000 ohms? 
Yes GO to the next step.
No REPAIR shorts on circuits having less than 10,000 ohms between other TR/PCM input signal circuits. RECONNECT all components, TEST the system for normal operation.
9 CHECK FOR AN INTERNAL SOLENOID BODY OPEN FOR THE TR SENSOR CIRCUITS
Yes GO to the next step.
No INSTALL a new solenoid body leadframe. See SOLENOID BODY LEADFRAME REMOVAL/INSTALLATION . RECONNECT all components. TEST the system for normal operation.
10 CHECK FOR VOLTAGE AND GROUND AT THE TR SENSOR CONNECTOR
  • Connect transaxle harness 0140-175t
  • Connect transaxle vehicle harness 0140-131 (2.5L), 0140-231 (3.0L).
  • Key in on position
  • Measure the voltage on the solenoid body leadframe between the TR sensor connector pins 1 (R) and 3 (B) solenoid body leadframe side.
G06157633

  • Is the voltage greater than 10 volts? 
Yes INSTALL a new TR sensor. See DIGITAL TRANSMISSION RANGE (TR) SENSOR REMOVAL/INSTALLATION . RECONNECT all components. TEST the system for normal operation. If the condition is still present, INSTALL a new PCM, See PCM REMOVAL/INSTALLATION - 2.5L/3.0L .
No INSTALL a new PCM. See PCM REMOVAL/INSTALLATION - 2.5L/3.0L . CONNECT all components. TEST the system for normal operation.