LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2011 >> Tribute i Touring, FWD >> Repair and Diagnosis >> Transmission >> Automatic Trans >> Symptom Troubleshooting [Transaxle] >> Pinpoint Test 3: Output Shaft Speed (OSS) Sensor >> Notes

Pinpoint Test 3: Output Shaft Speed (OSS) Sensor: Notes

NOTE:
  • Refer to the transaxle connector illustrations and solenoid body leadframe internal wiring diagram preceding these pinpoint tests. See TRANSAXLE CONNECTOR LAYOUTS  .
NOTE:
  • OSS codes may be a result of a bad common power or ground shared between the TR sensor, OSS sensor, and TSS sensor.
DIAGNOSTIC PROCEDURE

PINPOINT TEST 3 OUTPUT SHAFT SPEED (OSS) SENSOR
STEP INSPECTION ACTION
1 ELECTRONIC DIAGNOSTICS
  • Check to make sure the transaxle vehicle harness 0140-131 is fully seated, terminals are engaged in connector and in good condition before proceeding.
  • Have the items above been checked? 
Yes GO to the next step.
No CARRY OUT the checks. ERASE the codes. RERUN the OBD tests.
2 ELECTRONIC DIAGNOSTICS
  • Connect the scan tool.
  • Monitor the output shaft speed (OSS) sensor PIDs while test driving the vehicle.
  • Is the OSS sensor signal present and consistent? 
Yes The condition that set the DTC is intermittent and is not currently present. ERASE the codes. RERUN the OBD tests.
No GO to the next step.
3 CHECK THE VEHICLE HARNESS FOR AN OPEN CIRCUIT
  • Disconnect transaxle vehicle harness 0140-131.
  • Disconnect: PCM Transaxle Harness 0140-175t
  • Use a mirror to inspect both ends of the connectors for damage or pushed-out pins, corrosion, loose wires and missing or damaged seals.
  • Measure the resistance for the OSS sensor circuit, between the transaxle vehicle harness 0140-131 and the PCM transaxle harness 0140-175t harness using the Step 3 chart at the end of this pinpoint test.
  • Is the resistance less than 5 ohms? 
Yes GO to the next step.
No REPAIR the circuit(s) for an open. CONNECT all components. TEST the system for normal operation.
4 CHECK THE VEHICLE HARNESS FOR A SHORT TO GROUND
  • Disconnect: Transaxle Vehicle Harness 0140-132.
  • Measure the resistance for the OSS sensor circuit between the transaxle vehicle harness 0140-131 and ground using the Step 4 chart at the end of this pinpoint test.
  • Is the resistance greater than 10,000 ohms? 
Yes GO to the next step.
No REPAIR the circuit(s) for a short to ground. CONNECT all components. TEST the system for normal operation.
5 CHECK THE VEHICLE HARNESS FOR A SHORT TO VPWR
  • Check for voltage between the OSS sensor circuits and the transaxle vehicle harness 0140-131 using the Step 5 chart below.
  • Is any voltage present? 
Yes REPAIR the circuit(s) for a short to voltage. CONNECT all components. TEST the system for normal operation.
No GO to the next step.
6 CHECK THE SOLENOID BODY FOR AN INTERNAL OPEN CIRCUIT
  • Remove the main control cover. See MAIN CONTROL COVER REMOVAL/INSTALLATION .
  • Disconnect TR sensor.
  • Disconnect OSS sensor.
  • Use a mirror to inspect both ends of the connectors for damage or pushed-out pins, corrosion, loose wires and missing or damaged seals.
  • Measure the resistance of the solenoid body internal sensor power circuit between the main solenoid body leadframe connector pin 18, leadframe side and the OSS sensor connector pin 4, leadframe side.
G06157626G06157627G06157628

  • Measure the resistance of the solenoid body internal sensor signal circuit between the main solenoid body leadframe connector pin 19, leadframe side and the OSS sensor connector pin 3, leadframe side.
G06157626G06157627G06157628

  • Measure the resistance of the solenoid body internal sensor ground circuit between the main solenoid body leadframe connector pin 20, leadframe side and the OSS sensor connector pin 1, leadframe side.
G06157626G06157627G06157628

  • Is the resistance less than 5 ohms? 
Yes GO to the next step.
No INSTALL a new solenoid body leadframe. See SOLENOID BODY LEADFRAME REMOVAL/INSTALLATION . CONNECT all components. TEST the system for normal operation.
7 CHECK FOR VOLTAGE AND GROUND AT THE OSS SENSOR CONNECTOR
  • Connect: PCM 0140-175t
  • Connect: Transaxle Vehicle Harness 0140-131 (2.5L), 0140-231 (3.0L)
  • Key in ON position
  • Measure the voltage on the solenoid body leadframe between OSS sensor connector pins 1 and 4.
G06157629

  • Is the voltage greater than 10 volts? 
Yes INSTALL a new OSS sensor. See OUTPUT SHAFT SPEED (OSS) REMOVAL/INSTALLATION . TEST the system for normal operation. If the condition is still present, INSTALL a new PCM. See PCM REMOVAL/INSTALLATION - 2.5L/3.0L .
No INSTALL a new PCM. See PCM REMOVAL/INSTALLATION - 2.5L/3.0L . CONNECT all components. TEST the system for normal operation.