LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2011 >> Tribute i Touring, FWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 13 (Manual Transaxle) >> Output Shaft Disassembly/Assembly >> Assembly

Output Shaft Disassembly/Assembly: Assembly

WARNING: This page is about a different variant/trim than selected.
  1. Position the reverse main gear on the mainshaft.
    CAUTION:
    • Be careful with the orientation of the reverse main gear or damage to the component may occur.
      Fig 1: View Of Main Gear Shaft Spacer
      G05460178Courtesy of MAZDA MOTORS CORP.
  2. Using the Spindle/Axle Shaft Installer, press on a new reverse main gear.
    Fig 2: Pressing Reverse Main Gear Using Special Tool
    G05460179Courtesy of MAZDA MOTORS CORP.
  3. Install the 1st main gear.
  4. Using the Bearing/Oil Seal Plate and the 1st Gear Bushing Installer, press on the 1st main gear bushing.
    Fig 3: Pressing 1st Main Gear Bushing Using Special Tool
    G05460180Courtesy of MAZDA MOTORS CORP.
  5. Install the 1st gear needle bearing.
  6. Install the 1st gear synchronizer ring.
  7. Position a new 1st and 2nd gear synchronizer assembly on the mainshaft.
    CAUTION:
    • Make sure the synchronizer side with 3 notches is facing 1st gear and the synchronizer side with 4 notches is facing 2nd gear.
      Fig 4: Identifying Gear Synchronizer Assembly
      G05460156Courtesy of MAZDA MOTORS CORP.
  8. Using the Spindle/Axle Shaft Installer and the Bearing Puller, press on the 1st and 2nd gear synchronizer assembly.
    Fig 5: Pressing 1st And 2nd Gear Synchronizer Assembly Using Special Tools
    G05460182Courtesy of MAZDA MOTORS CORP.
  9. Install the 2nd gear synchronizer ring.
    Fig 6: Measuring Clearance Between Outer Synchronizer Ring And Synchronizer Cone
    G05460174Courtesy of MAZDA MOTORS CORP.
  10. Using the Bearing Oil Seal late and the 2nd Gear Bushing Installer, install the 2nd gear bushing.
    Fig 7: Installing 2nd Gear Bushing Using Special Tools
    G05460184Courtesy of MAZDA MOTORS CORP.
  11. Install the 2nd gear needle bearing.
  12. Install the 2nd main gear.
  13. Using the Spindle/Axle Shaft Installer and the Bearing Puller, press on a new 3rd main gear.
    CAUTION:
    • Be careful with the orientation of the 3rd main gear.
      Fig 8: Installing 3rd Main Gear Using Special Tools
      G05460185Courtesy of MAZDA MOTORS CORP.
  14. Install the 3rd/4th main gear shaft spacer.
    Fig 9: View Of Main Gear Shaft Spacer
    G05460178Courtesy of MAZDA MOTORS CORP.
  15. Measure the mainshaft components as indicated to select the appropriate 4th main gear adjusting shim. See the following table for shim thicknesses and install the 4th main gear adjusting shim.
    CAUTION:
    • Only one adjusting shim can be installed.
      Fig 10: Identifying Main Shaft Components Dimension With Specifications
      G05460187Courtesy of MAZDA MOTORS CORP.
    ADJUSTING SHIM SPECIFICATION

    mm in
    0.52 0.021
    0.60 0.024
    0.68 0.027
    0.76 0.030
    0.84 0.033
    0.92 0.036
    1.00 0.039
    1.08 0.043
  16. Using the Spindle/Axle Shaft Installer, press on a new 4th main gear.
    CAUTION:
    • Be careful with the orientation of the 4th main gear.
      Fig 11: Pressing 4th Main Gear Using Special Tool
      G05460188Courtesy of MAZDA MOTORS CORP.
  17. Using the Spindle/Axle Shaft Installer, press on a new 5th main gear.
    CAUTION:
    • Be careful with the orientation of the 5th main gear.
      Fig 12: Pressing 5th Main Gear Using Special Tool
      G05460189Courtesy of MAZDA MOTORS CORP.
  18. Measure the gap between the snap ring and the 5th main gear. The end play should be less than 0.1 mm (0.0039 in). See the following chart to select the appropriate snap ring thickness and install a new snap ring.
    Fig 13: Measuring Gap Between Snap Ring And 5th Main Gear
    G05460190Courtesy of MAZDA MOTORS CORP.
    SNAP RING SPECIFICATION

    mm in
    1.85 0.073
    1.90 0.075
    1.95 0.077
    2.00 0.079
    2.05 0.081
    2.10 0.083
    2.15 0.085
    2.20 0.087
  19. Using the Spindle/Axle Shaft Installer, press on the mainshaft rear bearing.
    CAUTION:
    • Be careful with the orientation of the mainshaft rear bearing.
      Fig 14: Installing Main Shaft Rear Bearing Using Special Tool
      G05460191Courtesy of MAZDA MOTORS CORP.
  20. Measure the gap between the mainshaft C-ring and the mainshaft rear bearing. See the following chart to select the appropriate C-ring thickness and install the C-ring.
    Fig 15: Measuring Gap Between Main Shaft C-Ring And Main Shaft Rear Bearing
    G05460192Courtesy of MAZDA MOTORS CORP.
    C-RING SPECIFICATION

    mm in
    2.535 0.0998
    2.565 0.1010
    2.595 0.1022
    2.625 0.1033
    2.655 0.1045
    2.685 0.1057
    2.715 0.1069
    2.745 0.1081
    2.775 0.1093
    2.805 0.1104
    2.835 0.1116
    2.865 0.1128
    2.895 0.1140
    2.925 0.1152
    2.955 0.1163
    2.985 0.1175
    3.015 0.1187
    3.045 0.1199
    3.075 0.1211
  21. Install the C-ring holder.
  22. Install a new snap ring.