LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2011 >> Tribute i Touring, FWD >> Repair and Diagnosis >> Body & Frame >> Seats >> Seat System >> Front Seat Backrest Disassembly/Assembly >> Disassembly

Front Seat Backrest Disassembly/Assembly: Disassembly

WARNING:
  • Always carry or place a live air bag module with the air bag and deployment door/trim cover/tear seam pointed away from the body. Do not set a live air bag module down with the deployment door/trim cover/tear seam face down. Failure to follow these instructions may result in serious personal injury in the event of an accidental deployment.
↓
WARNING:
  • Never probe the electrical connectors on safety belt buckle/retractor pretensioners or adaptive load limiting retractors. Failure to follow this instruction may result in the accidental deployment of the safety belt pretensioners or adaptive load limiting retractors, which Increases the risk of serious personal injury or death.
WARNING:
  • if the seat side air bag cover has been damaged or separated from its mounting, or if the air bag material has been exposed, install a new seat side air bag module. Never try to repair the seat side air bag module. Failure to follow these instructions may result in the seat side air bag deploying incorrectly, which increases the risk of serious personal injury or death in a crash.
WARNING:
  • Front seat backrest trim covers installed on seats equipped with seat side air bags cannot be repaired, A new trim cover must be installed. Cleaning is permissible. Failure to follow these instructions may result in the seat side air bag module deploying incorrectly and increase the risk of serious personal injury or death in a crash.
NOTE:
  • If a side air bag deployment took place, a new seat back pad, trim cover and side air bag module and nuts must be installed. The seat back frame should be replaced if necessary.
  • The air bag warning indicator illuminates when the restraints control module (RCM) fuse is removed and the ignition switch is ON, This is normal operation and does not indicate a supplemental restraint system (SRS) fault.
  • The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
  • Driver seat shown in illustration, passenger similar.

All Seats 

  1. Remove the front seat. See FRONT SEAT REMOVAL/INSTALLATION  .
  2. Remove the seat backrest. See FRONT SEAT BACKREST REMOVAL/INSTALLATION  .
  3. Remove the head restraint.
    • Release the 2 guide locks.
  4. Pull outward and remove the 2 head restraint guides.

    Seats With Lumbar Adjust 

  5. Remove the lumbar knob.

    All seats 

  6. Release the backrest trim cover J-clip.
    Fig 1: Locating Backrest Trim Cover J-Clip
    G05457309Courtesy of MAZDA MOTORS CORP.
  7. Partially invert the backrest trim cover up to the side air bag.
    • Place a hand between the seat backrest trim cover and the seat backrest foam pad and carefully separate the hook-and-loop strips.
    CAUTION:
    • Use care when separating the seat backrest trim cower from the hook-and-loop strips or the hook-and-loop strips may be torn from the seat backrest foam.
  8. Release the side air bag module deployment chute J-clip from around the side air bag module.
    Fig 2: Locating Side Air Bag Module Deployment Chute J-Clip
    G05457310Courtesy of MAZDA MOTORS CORP.
  9. Pull the side air bag module deployment chute and J-clips through opening in the backrest foam pad.
    Fig 3: Locating Side Air Bag Module Deployment Chute And J-Clip
    G07436621Courtesy of MAZDA MOTORS CORP.
  10. Detach the 2 side air bag module wiring harness retainers.
    Fig 4: Locating Side Air Bag Module Wiring Harness Retainers
    G05457312Courtesy of MAZDA MOTORS CORP.
  11. Remove the 2 side air bag module nuts and side air bag module.
  12. Invert and remove the backrest trim cover.
  13. Remove the backrest foam pad.

    Seats with lumbar adjust 

  14. Remove the 2 screws and position aside the lumbar adjust control.
  15. Release the lumbar support from the backrest frame wires and remove.