LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2011 >> Tribute i Touring, FWD >> Repair and Diagnosis >> Body & Frame >> Seats >> Seat System >> Front Seat Backrest Disassembly/Assembly >> Assembly

Front Seat Backrest Disassembly/Assembly: Assembly

WARNING:
  • Before installing the seat side air bag module/deployment chute assembly:
  • Inspect the side air bag module and mounting surfaces for any damage or foreign material.
  • Remove any foreign material from the mounting surfaces of the deployment chute, the seat backrest frame mounting bracket and the air bag module cavity in the seat backrest foam pad.
  • Install new parts if damaged.
  • Failure to follow these instructions may result in the seat side air bag deploying incorrectly, which increases the risk of serious personal injury or death in a crash.
WARNING:
  • Inspect the seat side air bag module and mounting surfaces for any damage or foreign material before installing the seat side air bag module. If any damage is found, install new components. If any foreign material is found, remove it. Failure to follow these instructions may result in the seat side air bag module deploying incorrectly and increase the risk of serious personal injury or death in a crash.
WARNING:
  • If the seat side air bag cover has been damaged or separated from its mounting, or if the air bag material has been exposed, install a new seat side air bag module. Never try to repair the seat side air bag module. Failure to follow these instructions may result in the seat side air bag deploying incorrectly, which increases the risk of serious personal injury or death in a crash.
CAUTION:
  • Make sure the side air bag module wiring harness is not pinched between the side air bag module and the mounting bracket. Damage to the wire harness may occur.

Seats With Lumbar Adjust 

  1. Install the lumbar support assembly to the backrest frame wires.
  2. Install the lumbar adjust control and 2 screws.

    All seats 

  3. Install the side air bag module and 2 nuts to the backrest frame mounting bracket.
    • Tighten to 5 N.m {0.5 kgf.m, 44 in.lbf}.
  4. Position the side air bag module wiring harness to the backrest frame and attach the retainers.
    Fig 1: Locating Side Air Bag Module Wiring Harness Retainers
    G05457312Courtesy of MAZDA MOTORS CORP.
  5. Install the backrest foam pad to the backrest frame.
  6. Position and roll the backrest trim cover down the backrest to the side air bag module.
    Fig 2: Locating Backrest Trim Cover Clips
    G04931162Courtesy of MAZDA MOTORS CORP.
  7. Feed the side air bag deployment chute and clips back through the opening in the backrest foam pad.
    Fig 3: Locating Side Air Bag Module Deployment Chute And J-Clip
    G05457311Courtesy of MAZDA MOTORS CORP.
    WARNING:
    • Check the seat side air bag deployment chute for damage. The deployment chute must not be repaired. If there is any damage to the deployment chute, a new seat back trim cover and deployment chute must be installed as a unit. Failure to follow these instructions may result in the seat side air bag module deploying incorrectly and increase the risk of serious personal injury or death in a crash.
  8. Install the side air bag module deployment chute and J-clips around the side air bag module and seat backrest frame.
    WARNING:
    • If the seat side air bag module deployment chute is not correctly positioned and closed, the seat side air bag module may not deploy correctly. Failure to follow these instructions may result in the seat side air bag module deploying incorrectly and increases the risk of serious personal injury or death in a crash.
    Fig 4: Locating Side Air Bag Module Deployment Chute J-Clip
    G05457310Courtesy of MAZDA MOTORS CORP.
  9. Roll the trim cover down the backrest and fasten the hook-and-loop strips.
  10. Fasten the backrest J-clip.

    Seats with lumbar adjust 

  11. Install the lumbar control knob.

    All seats 

  12. Install the seat backrest. See FRONT SEAT BACKREST REMOVAL/INSTALLATION  .
  13. Install the front seat. See SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
Fig 5: Locating Backrest Trim Cover J-Clip
G05457309Courtesy of MAZDA MOTORS CORP.