LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2009 >> 5 Touring, 2.3 3 >> Repair and Diagnosis >> Engine Performance >> System >> On-Board Diagnostic [Engine Control System L3] >> DTC P2006 [L3] >> Diagnostic procedure

Diagnostic procedure

DTC P2006 (L3) DIAGNOSTIC PROCEDURE

STEP INSPECTION ACTION
1 VERIFY FREEZE FRAME DATA HAS BEEN RECORDED 
  • Has FREEZE FRAME DATA been recorded?
Yes Go to the next step.
No Record the FREEZE FRAME DATA on repair order, then go to the next step.
2 VERIFY RELATED REPAIR INFORMATION AVAILABILITY 
  • Verify related Service Bulletins and/or on-line repair information availability.
  • Is any related repair information available?
Yes Perform repair or diagnosis according to the available repair information.
  • If the vehicle is not repaired, go to the next step.
No Go to the next step.
3 CLASSIFY INTERMITTENT CONCERN OR CONTINUOUS CONCERN 
  • Clear the DTC from the PCM memory using the M-MDS.
  • Drive the vehicle under the following conditions:
    • Engine coolant temperature is above 70°C {158°F}. 
    • Engine speed: 3,500 rpm or more 
    • Throttle opening angle is below as following
      • Engine speed below 1,500 rpm: above 35% 
      • Engine speed between 1,500-2,500 rpm: between 25-35% 
      • Engine speed above 2,500: below 25% 
  • Is the PENDING CODE for this DTC present?
Yes Go to the next step.
No Intermittent concern exists. Go to INTERMITTENT CONCERN TROUBLESHOOTING procedure.
(See INTERMITTENT CONCERN TROUBLESHOOTING [L3] .)
4 INSPECT VARIABLE TUMBLE SHUTTER VALVE SWITCH CONNECTOR AND VARIABLE TUMBLE SOLENOID VALVE CONNECTOR FOR POOR CONNECTION 
  • Turn the ignition switch off.
  • Disconnect the variable tumble solenoid valve connector and the variable tumble shutter valve switch connector.
  • Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
  • Is there any malfunction?
Yes Repair or replace the terminal, then go to Step 12.
No Go to the next step.
5 INSPECT VARIABLE TUMBLE SHUTTER VALVE ACTUATOR 
Yes Go to the next step.
No Repair or replace malfunctioning part according to inspection results, then go to Step 8.
6 INSPECT VARIABLE TUMBLE SOLENOID VALVE OR VARIABLE TUMBLE SHUTTER VALVE SWITCH SIGNAL CIRCUIT FOR SHORT TO GROUND 
  • Turn the ignition switch off.
  • Inspect for continuity between the following terminals and body ground.
    • PCM terminal 2I (harness-side).
    • PCM terminal 2AE (harness-side).
  • Is there continuity?
Yes Repair or replace the wiring harness for a short to ground, then go to Step 8.
No Go to the next step.
7 INSPECT PCM CONNECTOR FOR POOR CONNECTION 
  • Turn the ignition switch off.
  • Disconnect the PCM connector.
  • Inspect for poor connection at PCM terminals (such as damaged/pulled-out pins, corrosion).
  • Is there any malfunction?
Yes Repair the terminal, then go to Step 12.
No Go to the next step.
8 VERIFY TROUBLESHOOTING OF DTC P2006 COMPLETED 
  • Make sure to reconnect all disconnected connectors.
  • Start the engine.
  • Clear the DTC from the PCM memory using the M-MDS.
  • Start the engine.
  • Drive the vehicle under following conditions:
    • Engine coolant temperature is above 70°C {158°F}. 
    • Engine speed: below 3,500 rpm 
    • Throttle opening angle is below as following
      • Engine speed below 1,500 rpm: above 35% 
      • Engine speed between 1,500-2,500 rpm: between 25-35% 
      • Engine speed above 2,500: below 25% 
  • Is PENDING CODE for this DTC present?
Yes Replace the PCM, then go to the next step.
(See PCM REMOVAL/INSTALLATION [L3] .)
No Go to the next step.
9 VERIFY AFTER REPAIR PROCEDURE 
Yes Go to the applicable DTC troubleshooting.
(See DTC TABLE [L3] .)
No Troubleshooting completed.