LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2009 >> 5 Touring, 2.3 3 >> Repair and Diagnosis >> Engine Performance >> System >> On-Board Diagnostic [Engine Control System L3] >> DTC P0133 [L3] >> Diagnostic procedure

Diagnostic procedure

DTC P0133 (L3) DIAGNOSTIC PROCEDURE

STEP INSPECTION ACTION
1 VERIFY FREEZE FRAME DATA AND DIAGNOSTIC MONITORING TEST RESULTS HAVE BEEN RECORDED 
  • Have FREEZE FRAME DATA and DIAGNOSTIC MONITORING TEST RESULTS (A/F sensor, HO2S related) been recorded?
Yes Go to the next step.
No Record the FREEZE FRAME DATA and DIAGNOSTIC MONITORING TEST RESULTS on the repair order, then go to the next step.
2 VERIFY RELATED REPAIR INFORMATION AVAILABILITY 
  • Verify related service Bulletins and/or on-line repair information availability.
  • Is any related repair information available?
Yes Perform repair or diagnosis according to the available repair information.
  • If the vehicle is not repaired, go to the next step.
No Go to the next step.
3 VERIFY RELATED PENDING AND STORED DTC 
  • Turn the ignition switch off, then to the ON position (Engine off).
  • Verify the pending or stored DTCs using the M-MDS.
  • Is the DTC P0443 also present?
Yes Go to DTC P0443  troubleshooting procedures, then go to Step 10.
No Go to the next step.
4 IDENTIFY TRIGGER DTC FOR FREEZE FRAME DATA 
  • Is the DTC P0133 on FREEZE FRAME DATA?
Yes Go to the next step.
No Go to troubleshooting procedures for DTC on FREEZE FRAME DATA.
(See DTC TABLE [L3] .)
5 INSPECT INSTALLATION OF A/F SENSOR 
  • Inspect if the A/F sensor is loosely installed.
  • Is the A/F sensor installed securely.
Yes Go to the next step.
No Retighten the A/F sensor then go to Step 12.
(See AIR FUEL RATIO (A/F) SENSOR, HEATED OXYGEN SENSOR (HO2S) REMOVAL/INSTALLATION [L3] .)
6 INSPECT GAS LEAKAGE FROM EXHAUST SYSTEM 
  • Visually inspect if there any gas leakage between the exhaust manifold and A/F sensor.
  • Is there gas leakage?
Yes Repair or replace any malfunctioning exhaust part, then go to Step 12.
No Go to the next step.
7 INSPECT A/F SENSOR 
Yes Replace the A/F sensor, then go to Step 12.
(See AIR FUEL RATIO (A/F) SENSOR, HEATED OXYGEN SENSOR (HO2S) REMOVAL/INSTALLATION [L3] .)
No Go to the next step.
8 INSPECT FUEL LINE PRESSURE 
Yes Go to the next step.
No Repair or replace any malfunctioning exhaust part, then go to Step 12.
9 INSPECT PURGE SOLENOID VALVE 
Yes Repair or replace malfunctioning part, according-to inspection result.
Then go to Step 12.
No Go to the next step.
10 INSPECT SEALING OF ENGINE COOLANT PASSAGE 
Yes Repair or replace malfunctioning part according to the inspection result. Then go to the next step.
No Go to the next step.
11 INSPECT ENGINE COMPRESSION 
Yes Go to the next step.
No Overhaul the engine, then go to the next step.
12 VERIFY TROUBLESHOOTING OF DTC P0133 COMPLETED 
  • Make sure to reconnect all disconnected connectors.
  • Clear the DTC from the PCM memory using the M-MDS or equivalent.
  • Perform the "A/F sensor heater, HO2S heater, A/F sensor, HO2S, and TWC Repair Verification Drive Mode".

    (See OBD-II DRIVE MODE [L3] .)

  • Is the PENDING CODE for this DTC present?
Yes Replace the PCM, then go to the next step.
(See PCM REMOVAL/INSTALLATION [L3] .)
No Go to the next step.
13 VERIFY AFTER REPAIR PROCEDURE 
Yes Go to the applicable DTC inspection.
(See DTC TABLE [L3] .)
No
  • DTC troubleshooting completed.