LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2009 >> 5 Touring, 2.3 3 >> Repair and Diagnosis >> Engine Performance >> System >> On-Board Diagnostic [Engine Control System L3] >> DTC P0132 [L3] >> Diagnostic procedure

Diagnostic procedure

DTC P0132 (L3) DIAGNOSTIC PROCEDURE

STEP INSPECTION ACTION
1 VERIFY FREEZE FRAME DATA AND DIAGNOSTIC MONITORING TEST RESULTS HAVE BEEN RECORDED 
  • Have FREEZE FRAME DATA and DIAGNOSTIC MONITORING TEST RESULTS (A/F sensor, HO2S related) been recorded?
Yes Go to the next step.
No Record the FREEZE FRAME DATA and DIAGNOSTIC MONITORING TEST RESULTS on repair order, then go to the next step.
2 VERIFY RELATED REPAIR INFORMATION AVAILABILITY 
  • verify related Service Bulletins and/or on-line repair information availability.
  • Is any related repair information available?
Yes Perform repair or diagnosis according to the available repair Information.
  • If vehicle is not repaired, go to the next step.
No Go to the next step.
3 VERIFY RELATED PENDING OR STORED DTC 
  • Turn the ignition switch off, then to the ON position (Engine off).
  • Verify the pending code or stored DTCs using the M-MDS.
  • Are other DTCs present?
Yes Go to the appropriate DTC troubleshooting procedures.
(See DTC TABLE [L3] .)
No Go to the next step.
4 IDENTIFY TRIGGER DTC FOR FREEZE FRAME DATA 
  • Is the DTC P0132 on FREEZE FRAME DATA?
Yes Go to the next step.
No Go to troubleshooting procedures for DTC on FREEZE FRAME DATA. (See DTC TABLE [L3] .)
5 INSPECT A/F SENSOR CONNECTOR FOR POOR CONNECTION 
  • Turn the ignition switch off.
  • Disconnect the A/F sensor connector.
  • Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
  • Is there any malfunction?
Yes Repair or replace the terminal, then go to Step 9.
No Go to the next step.
6 INSPECT PCM CONNECTOR FOR POOR CONNECTION 
  • Turn the ignition switch off.
  • Disconnect the PCM connector.
  • Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
  • Is there any malfunction?
Yes Repair or replace the terminal, then go to Step 9.
No Go to the next step.
7 INSPECT A/F SENSOR 
Yes Replace the A/F sensor, then go to Step 9.
(See AIR FUEL RATIO (A/F) SENSOR, HEATED OXYGEN SENSOR (HO2S) REMOVAL/INSTALLATION [L3] .)
No Go to the next step.
8 INSPECT A/F SENSOR CIRCUIT FOR SHORT TO POWER SUPPLY 
  • Turn the ignition switch to the ON position (Engine off).
  • Measure the voltage between the following terminals and body ground:
    • A/F sensor terminal B (wiring-harness-side) and body ground
    • A/F sensor terminal D (wiring-harness-side) and body ground
    • A/F sensor terminal F (wiring-harness-side) and body ground
  • Is the voltage greater than 1.5 V?
Yes Repair or replace the wiring harness for a possible short to power supply, then go to the next step.
No Go to the next step.
9 VERIFY TROUBLESHOOTING OF DTC P0132 COMPLETED 
  • Make sure to reconnect all disconnected connectors.
  • Clear the DTC from the PCM memory using the M-MDS.
  • Perform the KOEO or KOER self-test.

    (See KOEO/KOER SELF TEST [L3] .)

  • Is the DTC P0132 present?
Yes Replace the PCM, then go to the next step.
(See PCM REMOVAL/INSTALLATION [L3] .)
No Go to the. next step.
10 VERIFY AFTER REPAIR PROCEDURE 
Yes Go to the applicable DTC inspection.
(See DTC TABLE [L3] .)
No DTC troubleshooting completed.