LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2008 >> 5 Touring, 2.3 3 >> Repair and Diagnosis >> Engine Performance >> Ignition System >> Technical Data [Engine Mechanical - L3) >> Engine Technical Data [L3]

Engine Technical Data [L3]

ENGINE TECHNICAL DATA

Item Specification
Standard valve clearance [Engine cold] IN: 0.22-0.28 mm {0.009-0.011 in}
EX: 0.27-0.33 mm {0.011-0.012 in}
Compression Standard: 1,372 kPa {14.00 kgf/cm2 , 199.1 psi} [290 rpm]
Minimum: 960 kPa {9.79 kgf/cm2 , 139.2 psi} [290 rpm]
Maximum difference between cylinders: 196.1 kPa {2.0 kgf/cm2 , 28.5 psi}
Cylinder head bolt length Standard: 145.2-145.8 mm {5.717-5.740 in}
Maximum: 146.5 mm {5.768 in}
Front oil seal press-in amount 0-0.5 mm {0-0.019 in}
Ignition timing Approx. BTDC 8°
Oil pressure (reference value) [oil temperature: 100 °C {212 °F}] 395-649 kPa {4.03-6.61 kgf/cm2 , 57.3-94.1 psi} [3,000 rpm]
Engine oil capacity (approx. quantity) Oil replacement: 3.9 L {4.1 US qt, 3.4 lmp qt}
Oil and oil filter replacement: 4.3 L {4.5 US qt, 3.8 lmp qt}
Total (dry engine): 4.6 L {4.9 US qt, 4.0 lmp qt}
Engine coolant capacity (approx. quantity) 7.5 L {7.9 US qt, 6.6 lmp qt}
Cooling system cap valve opening pressure 93.2-122.6 kPa {0.95-1.25 kgf/cm2 , 13.5-17.8 psi}
Thermostat initial-opening temperature 80-84 °C {176-183 °F}
Thermostat full-open temperature 97 °C {207 °F}
Thermostat full-open lift More than 8.0 mm {0.31 in}
Cooling fan motor current 17-23 A
Fuel line pressure (Reference) 350-410 kPa {3.57-4.18 kgf/cm2 , 50.8-59.4 psi}
Fuel hold pressure (Reference) 250 kPa {2.55 kgf/cm2 , 36.3 psi} or more
Fuel injector resistance 11.3-12.7 ohms [20 °C {68 °F}]
Leakage amount Less than 1 drop/2 min
Injection volume 275-312 ml {275-312 cc, 16.8-19.0 cu in}/min
Battery electrolyte specific gravity [20 °C {68 °F}] 1.22-1.29
Battery load test current 55D23L(48):180A 80D26L(55):195A
Battery back-up current (When the ignition switch is off, the ignition key is removed, and all doors are closed.) Vehicles with immobilizer system: 25-45 mA
Vehicles without immobilizer system: 30 mA or less
Battery slow charge current 55D23L (48): 4.5-5.5 A
80D26L (55): 5.5-6.5 A
Battery quick charge current [30 min] 55D23L (48): 30 A
80D26L (55): 35 A
Generator standard voltage [IG-ON] Terminal B: B+
Terminal P: Approx. 1 V or less
Terminal D: Approx. 0 V
Generator standard voltage [Idle, 20 °C {68 °F}] Terminal B: 13-15 V
Terminal P: Approx. 3-8 V
Terminal D: Turn the electrical loads (headlights, blower motor, rear window defroster, brake lights, etc) on and verify that the voltage reading increases.
Generator generated current minimum value 70 % of the nominal output current (nominal output current: 110 A) [ambient temp. 20 °C {68 °F}, voltage 13.0-15.0 V, both engine and generator are hot]
Generator rotor resistance (between slip rings) [20 °C {68 °F}] 1.8-2.2 ohms
Generator brush length Standard: 22.5 mm {0.886 in}
Minimum: 5.0 mm {0.20 in}
Generator brush spring force Standard: 4.1-5.3 N {0.42-0.54 kgf, 1.0-1.1 lbf}
Minimum: 1.7 N {0.17 kgf, 0.38 lbf}
Firing order 1-3-4-2 (all cylinders independent firing)
G05544770
Spark plug type LFG1 18 110 (ILTR5A-13G), L3Y2 18110
Spark plug gap 1.25-1.35 mm {0.0493-0.0531 in}
Spark plug resistance [25 °C {77 °F}] 3.0-7.5 kilohms
Starter no load test voltage 11 V
Starter no load test current 90 A or less
Starter pinion gap 0.5-2.0 mm {0.02-0.07 in}
Starter armature runout 0.05 mm {0.002 in} max.
Starter commutator diameter Standard: 29.4 mm {1.16 in}
Minimum: 28.8 mm {1.13 in}
Segment groove depth of starter commutator Standard: 0.4-0.6 mm {0.016-0.023 in}
Minimum: 0,2 mm {0.008 in}
Starter brush length Standard: 12.3 mm {0.48 in}
Minimum: 7.0 mm {0.28 in}
Starter brush spring force Standard: 18.3-24.9 N {1.87-2.53 kgf, 4.12-5.59 lbf}
Minimum: 5.9 N {0.6 kgf, 1.3 lbf}

Idle speed: MTX 

IDLE SPEED SPECIFICATION (MTX)

Load status Idle speed (rpm)
Neutral
No load 600-700
A/C on Refrigerant pressure switch (middle pressure) is off 700-800
Refrigerant pressure switch (middle pressure) is on
Electrical loads on Generator generating current value 38-48 A 650-750
Over 48 A 700-800

Idle speed: ATX 

IDLE SPEED SPECIFICATION (ATX)

Load status Idle speed (rpm)
N range D range
No load 650-750 550-650
A/Con Refrigerant pressure switch (middle pressure) is off 650-750
Refrigerant pressure switch (middle pressure) is on 670-770
Electrical loads on Generator generating current value 38-48 A 650-750 600-700
Over 48 A 700-800 670-770

Engine oil specification 

ENGINE OIL SPECIFICATION

Item U.S.A. and CANADA Except U.S.A. and CANADA
Engine oil grade
G05544771
G05544772
Engine oil viscosity 5W-20 5W-20 (If SAE 5W-20 engine oil is not available in your market, use SAE 5W-30 engine oil.)