LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2006 >> Tribute s, FWD >> Repair and Diagnosis >> Restraints >> Restraints Control Systems >> Seat Belt System >> Rear Safety Belt Retractor >> Removal

Rear Safety Belt Retractor: Removal

WARNING:
  • All safety belt assemblies including retractors, buckles, belt tension sensor (BTS), if equipped, front seat belt buckle support assemblies (slide bar), if equipped, shoulder belt height adjusters, if equipped, child safety seat tether bracket assemblies, if equipped, and attaching hardware should be inspected after any collision. Mazda recommends new safety belt assemblies be installed unless a qualified technician finds existing assemblies show no damage and operate correctly. Safety belt assemblies not in use during a collision should also be inspected and new assemblies installed if either damage or incorrect operation is noted.

The Automatic Locking Retractor (ALR) feature of the safety belt retractor must be checked by a qualified technician to verify that the ALR feature for a child seat is functioning properly, in addition to other checks for proper safety belt system function. A belt and retractor assembly must be replaced if the safety belt assembly's "automatic locking retractor" feature or any other safety belt function is not operating properly. Failure to replace the belt and retractor assembly could increase the risk of injury in collisions.

NOTE:
  • Driver-side shown, passenger-side similar.

    Vehicles with rear power point 

  1. Disconnect the battery ground cable and wait at least one minute. See BATTERY DISCONNECT .
  2. Both rear safety belt retractors 

    Fig 1: Remove the rear door scuff plate.
    G04322347Courtesy of MAZDA MOTORS CORP.
  3. Remove the rear door scuff plate.
    1. Open the cover.
    2. Remove the two pin-type retainers (one shown).
    3. Remove the rear door scuff plate.
    Fig 2: Separate the weather stripping from the C-pillar
    G04322348Courtesy of MAZDA MOTORS CORP.
  4. Separate the weather stripping from the C-pillar.
    Fig 3: Pivoting Rear Seat Cushion Forward
    G04322349Courtesy of MAZDA MOTORS CORP.
  5. Pivot the rear seat cushion forward.
    Fig 4: Removing Safety Belt Anchor
    G04322350Courtesy of MAZDA MOTORS CORP.
  6. Remove the safety belt anchor.
    1. Using the special tool, remove the bolt.
    2. Remove the safety belt anchor.
      Fig 5: Removing Rear Safety Belt Guide Cover
      G04322351Courtesy of MAZDA MOTORS CORP.
      NOTE:
      • The rear safety belt guide has been removed for clarity.
  7. From behind the rear safety belt guide cover, release the retaining tabs, slide the cover up and remove it.
  8. Fig 6: Removing Safety Belt Guide
    G04322352Courtesy of MAZDA MOTORS CORP.
  9. Remove the rear safety belt guide.
    1. Using the special tool, remove the bolt.
    2. Remove the safety belt guide.
      • If necessary, remove the spacer from the rear safety belt guide.
        Fig 7: Lowering Second Row Seat Backrest
        G04322353Courtesy of MAZDA MOTORS CORP.
  10. Lower the second row seat backrest.
    Fig 8: Separating Rear Hatch Weather Stripping
    G04322354Courtesy of MAZDA MOTORS CORP.
  11. Separate the rear hatch weather stripping along the scuff plate and rear quarter trim panel on the side of the safety belt retractor being serviced.
    Fig 9: Removing Rear Hatch Scuff Plate
    G04322355Courtesy of MAZDA MOTORS CORP.
  12. Remove the rear hatch scuff plate.
    • Pull up to release the retaining clips.
  13. All Vehicles 

    Fig 10: Removing Cargo Cover
    G04322356Courtesy of MAZDA MOTORS CORP.
  14. Remove the cargo cover.
    Fig 11: Removing Cargo Cover Hold-Down
    G04322357Courtesy of MAZDA MOTORS CORP.
  15. Remove the cargo cover hold-down.
  16. RH side only 

    Fig 12: Removing Rear Quarter Trim Panel (RH Side Only)
    G04322358Courtesy of MAZDA MOTORS CORP.
  17. Pull out to release the retaining clips and remove the rear quarter trim panel.
  18. LH side only 

    Fig 13: Removing Rear Quarter Trim Panel (LH Side Only)
    G04322359Courtesy of MAZDA MOTORS CORP.
  19. Pull out to release the retaining clips and remove the rear quarter trim panel.
    Fig 14: Disconnecting Power Point Electrical Connector
    G04322360Courtesy of MAZDA MOTORS CORP.
  20. Remove the rear quarter trim panel.
    • If equipped, disconnect the power point electrical connector.
  21. Both rear safety belt retractors 

    Fig 15: Removing Rear Safety Belt Retractor
    G04322361Courtesy of MAZDA MOTORS CORP.
  22. Remove the rear safety belt retractor.
    1. Using the special tool, remove the bolt.
    2. Remove the rear safety belt retractor.