LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2005 >> Tribute i, 4WD, Standard >> Repair and Diagnosis >> Transmission >> Manual Trans >> Manual Transaxle >> Output Shaft >> Assembly

Output Shaft: Assembly

Fig 1: Removing/Installing Main Shaft
G03725621Courtesy of MAZDA MOTORS CORP.
  1. Inspect all main shaft parts for damage, peeling, dents, uneven wear, bending, etc. Install new parts as necessary.
  2. Inspect the synchronizer rings for damage. Install new parts as necessary.
    Fig 2: Inspecting Synchronizer Rings For Damage
    G03725622Courtesy of MAZDA MOTORS CORP.
  3. NOTE:
    • Outer synchronizer ring, synchronizer cone, and inner synchronizer ring has a set control clearance. If measurement exceeds specification, replace all 3 parts as a set.
    Fig 3: Installing Inner Ring, Outer Ring And Synchronizer Cone
    G03725623Courtesy of MAZDA MOTORS CORP.
  4. Check the clearances of the double cone synchronizer for 1st gear. If any of the clearances are beyond specification, install new parts as a set.
    PARTS DESCRIPTION

    1 Inner ring
    2 Synchronizer cone
    3 Outer ring
  5. NOTE:
    • If the difference in measurements is greater than 0.2mm (0.078 in), install new parts.
    Fig 4: Measuring Clearance Between Synchronizer Cone And Inner Synchronizer Ring
    G03725624Courtesy of MAZDA MOTORS CORP.
  6. Using the special tool, measure the clearance at 2 or more points diagonally between the synchronizer cone and the inner synchronizer ring. Install new parts if not within specification.
  7. NOTE:
    • If the difference in measurements is greater than 0.2mm (0.078 in), install new parts.
    Fig 5: Measuring Clearance Between Outer Synchronizer Ring And Synchronizer Cone
    G03725625Courtesy of MAZDA MOTORS CORP.
  8. Measure the clearance between the outer synchronizer ring and the synchronizer cone at 2 or more points diagonally opposite and calculate the mean value. Install new parts if not within specification.
  9. CAUTION:
    • Outer synchronizer ring, synchronizer cone, and inner synchronizer ring has a set control clearance. If measurement exceeds specification, replace all 3 parts as a set.
  10. Check the clearances of the triple cone synchronizer for 2nd gear. If any of the clearances are beyond specification, install new parts as a set.
  11. NOTE:
    • If the difference in measurements is greater than 0.3 mm (0.01 in), install new parts.
    Fig 6: Measuring Clearance At 2 Or More Points Diagonally Opposite (1 Of 3)
    G03725626Courtesy of MAZDA MOTORS CORP.
  12. Measure the clearance at 2 or more points diagonally opposite and calculate the mean. If the measurement is not within specification, install new parts.
  13. NOTE:
    • If the difference in measurements is greater than 0.2 mm (0.007 in).
    Fig 7: Measuring Clearance At 2 Or More Points Diagonally Opposite (2 Of 3)
    G03725627Courtesy of MAZDA MOTORS CORP.
  14. Measure the clearance at 2 or more points diagonally opposite and calculate the mean. If the measurement is not within specification, install new parts.
  15. NOTE:
    • If the difference in measurements is greater than 0.3 mm (0.01 in), install new parts.
    Fig 8: Measuring Clearance At 2 Or More Points Diagonally Opposite (3 Of 3)
    G03725628Courtesy of MAZDA MOTORS CORP.
  16. Measure the clearance at 2 or more points diagonally opposite and calculate the mean. If the measurement is not within specification, install new parts.
  17. CAUTION:
    • Be careful with orientation of the reverse main gear.
    Fig 9: Positioning Reverse Main Gear On Main Shaft
    G03725629Courtesy of MAZDA MOTORS CORP.
  18. Position the reverse main gear on the main shaft.
  19. Using the special tool, install the reverse main gear.
    Fig 10: Installing Reverse Main Gear
    G03725630Courtesy of MAZDA MOTORS CORP.
  20. Using the special tools, install the 1st main gear bushing.
    Fig 11: Installing 1st Main Gear Bushing
    G03725631Courtesy of MAZDA MOTORS CORP.
  21. CAUTION:
    • Make sure the synchronizer side with 3 notches is facing 1st gear and the synchronizer side with 4 notches is facing 2nd gear.
    Fig 12: Positioning 1st And 2nd Gear Synchronizer Assembly On Main Shaft
    G03725632Courtesy of MAZDA MOTORS CORP.
  22. Position the 1st and 2nd gear synchronizer assembly on the main shaft.
  23. Using the special tools, install the 1st gear syncronizer.
    Fig 13: Installing 1st Gear Synchronizer
    G03725633Courtesy of MAZDA MOTORS CORP.
  24. Using the special tools, install the 2nd gear bushing.
    Fig 14: Installing 2nd Gear Bushing
    G03725634Courtesy of MAZDA MOTORS CORP.
  25. Install the 2nd gear syncronizer.
  26. Install 2nd needle bearing and 2nd gear.
  27. CAUTION:
    • Be careful with the orientation of the 3rd main gear.
    Fig 15: Installing 3rd Main Gear
    G03725635Courtesy of MAZDA MOTORS CORP.
  28. Using the special tools, install the 3rd main gear.
  29. CAUTION:
    • Only one adjusting shim can be installed.
    Fig 16: Measuring Main Shaft Components
    G03725636Courtesy of MAZDA MOTORS CORP.
  30. Measure the main shaft components as indicated to select the appropriate 4th main gear adjusting shim. See the following table for shim thicknesses and install the 4th main gear adjusting shim.
    SHIM THICKNESS SPECIFICATION

    mm in
    0.52 0.021
    0.60 0.024
    0.68 0.027
    0.76 0.030
    0.84 0.033
    0.92 0.036
    1.00 0.039
    1.08 0.043
  31. CAUTION:
    • Be careful with the orientation of the 4th main gear.
    Fig 17: Installing 4th Main Gear
    G03725637Courtesy of MAZDA MOTORS CORP.
  32. Using the special tools, install the 4th main gear.
  33. CAUTION:
    • Be careful with the orientation of the 5th main gear.
    Fig 18: Installing 5th Main Gear
    G03725638Courtesy of MAZDA MOTORS CORP.
  34. Using the special tool, install the 5th main gear.
  35. Measure the gap between the snap ring and the 5th main gear. End play should be less than 0.1 mm (0.039 in). See the following chart to select the appropriate snap ring thickness and install the snap ring.
    Fig 19: Measuring Gap Between Snap Ring And 5th Main Gear
    G03725639Courtesy of MAZDA MOTORS CORP.
    SNAP RING THICKNESS SPECIFICATION

    mm in
    1.85 0.073
    1.90 0.075
    1.95 0.077
    2.00 0.079
    2.05 0.081
    2.10 0.083
    2.15 0.085
    2.20 0.087
  36. CAUTION:
    • Be careful with the orientation of the main shaft rear bearing.
    Fig 20: Installing Main Shaft Rear Bearing
    G03725640Courtesy of MAZDA MOTORS CORP.
  37. Using the special tool, install the main shaft rear bearing.
  38. Measure the gap between the main shaft C-ring and the main shaft rear bearing. See the following chart to select the appropriate C-ring thickness and install the C-ring.
    Fig 21: Measuring Gap Between Main Shaft C-Ring And Main Shaft Rear Bearing
    G03725641Courtesy of MAZDA MOTORS CORP.
    C-RING THICKNESS SPECIFICATION

    mm in
    2.535 0.0998
    2.565 0.1010
    2.595 0.1022
    2.625 0.1033
    2.655 0.1045
    2.685 0.1057
    2.715 0.1069
    2.745 0.1081
    2.775 0.1093
    2.805 0.1104
    2.835 0.1116
    2.865 0.1128
    2.895 0.1140
    2.925 0.1152
    2.955 0.1163
    2.985 0.1175
    3.015 0.1187
    3.045 0.1199
    3.075 0.1211
  39. Install the mainshaft rear bearing retainers
    1. Install the C-ring.
    2. Install the C-ring holder.
    3. Install the snap ring.
    Fig 22: Illustration For Step 1-3
    G03725642Courtesy of MAZDA MOTORS CORP.