LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2005 >> Tribute i, 4WD, Standard >> Repair and Diagnosis >> Engine Performance >> Symptom Troubleshooting [Engine Control System] >> Brake Pedal Position (BPP) Switch Malfunction

Brake Pedal Position (BPP) Switch Malfunction

NOTE: The following test procedures are for DTCs P0703, P1572, and P1703.
Fig 1: Brake Pedal Position (BPP) Switch Malfunction Detection Condition Possible Cause
G03723713Courtesy of MAZDA MOTORS CORP.
BRAKE PEDAL POSITION (BPP) SWITCH MALFUNCTION INSPECTION/ACTION CHART

STEP INSPECTION ACTION
1
  • Was PCM Quick Test performed? 
Yes If brake pedal was applied during KOEO Self-Test, perform KOEO again and avoid applying brake pedal during test.
If brake pedal was not applied and released during KOER Self-Test, perform KOER again and make sure to apply and release brake pedal.
For KOEO DTC P0703, P1572 or P1703:
Go to next step.
For KOER DTC P0703, P1572 or P1703:
Go to step 3.
No Perform PCM Quick Test. See PCM QUICK TEST  .
2 DTCS P0703 AND P1703: CHECK OPERATION OF STOPLAMPS
  • Apply and release the brake pedal several times and observe stoplamp operation.
  • Do brake lamps operate normally? 
Yes Go to next step.
No For stoplamps never on:
Go to step 4.
For stoplamps always on:
Go to step 6.
3 CHECK FOR PCM BPP/BOO PID CYCLING
  • Key On, Engine Off (KOEO).
  • Access BPP/BOO PID with WDS or equivalent tester.
  • Apply and release brake pedal several times while viewing BPP/BOO PID.
  • Does the BPP/BOO PID cycle ON/OFF? 
Yes See TEST 3: INTERMITTENT  .
No Go to step 9.
4 CHECK FOR POWER TO BPP SWITCH
NOTE:
  • Check the condition of the stoplamp bulbs before starting this test.
  • Disconnect BPP switch.
  • Measure B+ input voltage between BPP switch harness connector and chassis ground.
  • Is voltage greater than 10 V? 
Yes Go to next step.
No Verify integrity of fuse for B+ to brake pedal position switch. If OK, repair open in B+ circuit. If fuse is damaged, check B+ circuit, BPP circuit, stop lamp PWR circuit and any other associated circuits for short to ground. See SYSTEM WIRING DIAGRAMS for schematic information. Repair as necessary.
Go to step 10.
5 VERIFY INTEGRITY OF BPP SWITCH
  • Connect multimeter test probes to terminals at the BPP switch.
  • Apply brake pedal while monitoring reading.
  • Is the resistance less than 5.0 ohms? 
Yes Repair open circuit between BPP switch and stoplamp ground.
Go to step 10.
No Replace BPP switch.
See BRAKE PEDAL POSITION (BPP) SWITCH .
Go to step 10.
6 VERIFY BPP SWITCH IS NOT ALWAYS CLOSED
  • Key OFF.
  • Disconnect BPP switch harness connector.
  • Key On, Engine Off (KOEO).
  • Are stoplamps still on? 
Yes Go to next step.
No Verify proper installation of BPP switch.
If OK, replace switch.
See BRAKE PEDAL POSITION (BPP) SWITCH .
Go to step 10.
7 CHECK FOR SHORT TO POWER IN PCM
  • Key OFF.
  • Disconnect PCM.
  • Key ON, Engine OFF (KOEO).
  • Are stoplamps still on? 
Yes Go to next step.
No Replace PCM.
See POWERTRAIN CONTROL MODULE (PCM) .
Go to step 10.
8 CHECK STOPLAMP CIRCUIT FOR SHORT TO POWER IN HARNESS
  • One at a time, disconnect all modules associated with the stoplamp circuit (PCM, cruise control, SJB, 4WABS and RABS). After disconnecting each module, turn key on and observe stoplamps. Turn key off. Repeat until each associated module has been disconnected or stoplamps turn off.
  • Did stoplamps turn off when any of the modules were disconnected? 
Yes Go to the appropriate information for further diagnosis of appropriate module.
No Repair short to power in stoplamp circuit.
Go to step 10.
9 CHECK FOR BPP CIRCUIT CYCLING
  • Key OFF.
  • Disconnect PCM.
  • Install Breakout Box, leave PCM disconnected.
  • Measure voltage between PCM test pin C8 (BPP) and PCM test pin C49 (PWR GND) while applying and releasing the brake.
  • Does the voltage cycle? 
Yes Replace PCM.
See POWERTRAIN CONTROL MODULE (PCM) .
Go to next step.
No Repair open in BPP circuit to PCM.
Go to next step.
10 VERIFY TROUBLESHOOTING OF DTCs COMPLETED
  • Make sure to reconnect all disconnected connectors.
  • Clear DTCs from PCM memory using WDS or equivalent tester generic OBD II function.
  • Perform PCM Quick Test. See PCM QUICK TEST  .
  • Is same DTC present? 
Yes Replace PCM.
See POWERTRAIN CONTROL MODULE (PCM) .
Repeat PCM Quick Test. See PCM QUICK TEST  .
No If any other DTC is present, go to applicable DTC inspection.
If no DTC is present, troubleshooting complete.