LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2003 >> B4000 Base, Automatic >> Repair and Diagnosis (Single Page) >> Drivelines & Axles >> Differentials & Drive Axles >> Differential >> Axle And Differential Front Disassembly/Assembly >> Disassembly Note

Disassembly Note

  1. Remove the front axle assembly; see AXLE ASSEMBLY FRONT REMOVAL/INSTALLATION .
  2. Install the axle on bench.
    NOTE:
    • Place a suitable drain pan under the axle.
  3. Drain the axle fluid.
    1. Remove the ten differential cover bolts.
    2. Remove the differential cover.
  4. Remove the axle shaft using a jerking motion.
    Fig 1: Removing Axle Shaft
    G01923821Courtesy of MAZDA MOTORS CORP.
  5. Use Converter Seal Remover ST  49 UN01 0870 or equivalent and Impact Slide Hammer ST  49 0223 630B and Adapter ST  49 UN11 101 to remove the LH axle seal.
    Fig 2: Removing LH Axle Seal
    G01923822Courtesy of MAZDA MOTORS CORP.
  6. Use Bearing Cup Puller ST  308-047 or equivalent and Impact Slide Hammer ST  49 0223 630B and Adapter ST  49 UN11 101 to remove the LH axle bearing.
    Fig 3: Removing LH Axle Bearing
    G01923823Courtesy of MAZDA MOTORS CORP.
  7. Use Converter Seal Remover ST  49 UN01 0870 or equivalent and Impact Slide Hammer ST  49 0223 630B and Adapter ST  49 UN11 101 to remove the RH axle shaft seal.
    Fig 4: Removing RH Axle Shaft Seal
    G01923824Courtesy of MAZDA MOTORS CORP.
  8. Use Bearing Remover ST  307-318 or equivalent and Impact Slide Hammer ST  49 0223 630B and Adapter ST  49 UN11 101 to remove the RH axle bearing.
    Fig 5: Removing RH Axle Bearing
    G01923825Courtesy of MAZDA MOTORS CORP.
    CAUTION:
    • The matched numbers or letters stamped on both of the differential bearing caps and the axle housing must correspond upon assembly.
  9. Remove the differential bearing caps.
    1. Remove the four bolts.
    2. Remove the two differential bearing caps.
    Fig 6: Removing Differential Bearing Caps
    G01923826Courtesy of MAZDA MOTORS CORP.
    CAUTION:
    • The ST bolts have a minimum thread engagement.
  10. Install Spreader Adapters ST  49 UN01 027.
    Fig 7: Installing Spreader Adapters
    G01923827Courtesy of MAZDA MOTORS CORP.
    NOTE:
    • Make sure the indicator needle is in the spreader adapter hole.
  11. Install Differential Housing Spreader ST  49 UN01 026 and Dial Indicator with Bracketry.
    1. Install ST  49 UN01 026.
    2. Install Dial Indicator with Bracketry and Clutch Housing Alignment Adapter ST  308-021.
    Fig 8: Installing Dial Indicator With Bracketry And Clutch Housing Alignment Adapter
    G01923828Courtesy of MAZDA MOTORS CORP.
    CAUTION:
    • Over-spreading may cause damage to the axle housing.
  12. Spread the axle housing.
    1. Adjust the Dial Indicator to zero.
    2. Tighten screw from Differential Housing Spreader ST  49 UN01 026 until the axle housing is spread.
    3. Remove Dial Indicator with Bracketry.
    Fig 9: Spreading Axle Housing
    G01923829Courtesy of MAZDA MOTORS CORP.
    CAUTION:
    • Wood blocks must be used to avoid axle housing damage.
  13. Remove the differential case from the axle housing.
    1. Position the wood blocks.
    2. Use two pry bars; push down on the pry bars.
    3. Remove the differential case.
    4. Remove Differential Housing Spreader ST  49 UN01 026.
    Fig 10: Removing Differential Case From Axle Housing
    G01923830Courtesy of MAZDA MOTORS CORP.
  14. Measure the pinion bearing preload.
    • Use a beam type torque wrench to measure the torque required to maintain rotation of the pinion and record the measure for reference during assembly.
  15. Index mark the companion flange to the pinion stem.
    Fig 11: Marking Companion Flange And Pinion Stem
    G01923831Courtesy of MAZDA MOTORS CORP.
  16. Use Coupling Holder ST  205-126 to hold the companion flange while removing the pinion nut.
    Fig 12: Removing Pinion Nut
    G01923832Courtesy of MAZDA MOTORS CORP.
  17. Use a 2-jaw puller to remove the companion flange.
    WARNING:
    • Gear teeth may have sharp edges. When handling gear, use care to avoid personal injury.
    CAUTION:
    • Use a soft mallet to drive the pinion out of the axle housing.
  18. Remove the pinion from the axle housing.
    1. Hold the pinion inside the axle housing.
    2. Use a soft face hammer to remove the pinion from the axle housing.
    Fig 13: Removing Pinion From Axle Housing
    G01923833Courtesy of MAZDA MOTORS CORP.
  19. Use Converter Seal Remover ST  49 UN01 0870 or equivalent and Impact Slide Hammer ST  49 0223 630B and Adapter ST  49 UN11 101 to remove the pinion seal.
    Fig 14: Removing Pinion Seal
    G01923834Courtesy of MAZDA MOTORS CORP.
  20. Remove the oil slinger (1) and the differential pinion bearing (2).
    Fig 15: Removing Oil Slinger And Differential Pinion Bearing
    G01923835Courtesy of MAZDA MOTORS CORP.
  21. Remove the outer differential pinion bearing cup by tapping alternately on each side to prevent it from cocking in the bore.
    Fig 16: Removing Outer Differential Pinion Bearing Cup
    G01923836Courtesy of MAZDA MOTORS CORP.
  22. Remove the inner differential pinion bearing cup by tapping alternately on each side to prevent it from cocking in the bore.
    Fig 17: Removing Inner Differential Pinion Bearing Cup
    G01923837Courtesy of MAZDA MOTORS CORP.
  23. Remove the differential pinion bearing.
    1. Install the Pinion Bearing Cone Remover 205-055 or equivalent on the differential pinion bearing assembly.
    2. Position the Pinion Bearing Cone Remover 205-055 or equivalent and the differential pinion bearing assembly in a press.
    3. Press the differential pinion bearing off.
    Fig 18: Removing Differential Pinion Bearing
    G01923838Courtesy of MAZDA MOTORS CORP.
    NOTE:
    • Measure the pinion position shim with a micrometer and record the thickness (use this as a reference to compare the shim gauge reading prior to installing the differential pinion bearing).
  24. Remove the pinion position shim from the differential pinion gear.
    Fig 19: Removing Pinion Position Shim From Differential Pinion Gear
    G01923839Courtesy of MAZDA MOTORS CORP.
  25. Remove the ring gear.
    1. Remove the eight bolts.
    2. Use a drift punch to separate the ring gear from the differential case.