LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2003 >> B2300 Base, Standard >> Repair and Diagnosis >> Steering >> Power Steering >> Power Steering System >> Steering Gear Removal/Installation >> 4x4 Removal

4x4 Removal

  1. Turn the wheel to the straight ahead position and turn the ignition switch to the OFF position.
  2. Remove the wheel and tire assemblies; see WHEEL & TIRE REMOVAL/INSTALLATION .
  3. Remove the fluid cooler; see POWER STEERING FLUID COOLER REMOVAL/INSTALLATION  .
  4. Remove the four air deflector retaining screws.
    Fig 1: Removing Air Deflector Retaining Screws
    G01924821Courtesy of MAZDA MOTORS CORP.
  5. Pull downward on the air deflector to disengage the retaining pins.
    Fig 2: Removing Air Deflector
    G01924822Courtesy of MAZDA MOTORS CORP.
  6. Loosen the LH tie rod jam nut.
  7. Remove and discard the cotter pins and nuts.
    Fig 3: Removing Cotter Pins And Nuts
    G01924823Courtesy of MAZDA MOTORS CORP.
    CAUTION:
    • Do not damage the tie-rod boot when installing the special tool.
    NOTE:
    • Remove the adapter from the ball end of the special tool. Apply a small amount of grease to the tie-rod end stud and the ball of the special tool.
  8. Using the special tool, separate the tie rod ends from the wheel knuckles.
    Fig 4: Removing Tie Rod Ends From Wheel Knuckles
    G01924824Courtesy of MAZDA MOTORS CORP.
  9. Remove the LH tie rod end.
    1. Count and record the number of turns required to remove the tie rod end.
  10. Remove front stabilizer bar nut and washer assembly. See FRONT SUSPENSION COMPONENTS .
    1. Note or mark the driver side end of the stabilizer bar for correct installation.
    CAUTION:
    • Do not allow the intermediate shaft to rotate while it is disconnected from the steering gear or damage to the clockspring can result. If there is evidence that the intermediate shaft has rotated, the clock-spring must be removed and re-centered. For additional information see AIR BAG SLIDING CONTACT REMOVAL/INSTALLATION .
  11. Remove the pinch bolt and detatch the intermediate shaft from the gear.
    1. Discard the bolt.
    Fig 5: Removing Intermediate Shaft From Gear
    G01924825Courtesy of MAZDA MOTORS CORP.
  12. Remove the nut and disconnect the lines.
    Fig 6: Disconnecting Lines
    G01924826Courtesy of MAZDA MOTORS CORP.
  13. Plug or cap the power steering return hose, power steering pressure hose and the steering gear ports to prevent entry of dirt.
    CAUTION:
    • Hold the tops of the steering gear to crossmember stud bolts to avoid damaging the steering gear fluid transfer tubes.
  14. Remove the nuts.
    Fig 7: Removing Nuts
    G01924827Courtesy of MAZDA MOTORS CORP.
  15. Remove the mounting stud, nut, washer and stop assemblies.
    Fig 8: Removing Mounting Stud, Nut, Washer And Stop Assemblies
    G01924828Courtesy of MAZDA MOTORS CORP.
  16. Remove the steering gear to crossmember bushings.
    Fig 9: Removing Steering Gear To Crossmember Bushings
    G01924829Courtesy of MAZDA MOTORS CORP.
  17. Rotate the steering gear control valve housing toward the front of the vehicle.
    Fig 10: Rotating Steering Gear Control Valve Housing
    G01924830Courtesy of MAZDA MOTORS CORP.
  18. Turn the steering gear input shaft to the right until the stop is reached.
  19. Move the steering gear as far to the RH side of the vehicle as possible.
    Fig 11: Moving Steering Gear As Far To RH Side
    G01924831Courtesy of MAZDA MOTORS CORP.
  20. Move the LH wheel spindle tie-rod forward to clear the frame crossmember.
    Fig 12: Moving LH Wheel Spindle Tie-Rod
    G01924832Courtesy of MAZDA MOTORS CORP.
  21. Remove the steering gear from the vehicle.
Fig 13: Removing Steering Gear From Vehicle
G01924833Courtesy of MAZDA MOTORS CORP.