LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 1995 >> B3000 Base, Automatic >> Repair and Diagnosis >> Brakes >> Traction Control >> Anti-Lock Brake System - Four Wheel >> Circuit Tests >> Test B: Main Relay Output Circuit Failure

Test B: Main Relay Output Circuit Failure

  1. Check Voltage At Pin No. 17

    Measure and record battery voltage. Disconnect control module 40-pin connector. Install Breakout Box (49-UN01-058) with proper overlay. Connect a jumper wire between breakout box pins No. 19 and 1, or pins No. 19 and 14. Turn ignition on. Using DVOM, measure voltage between breakout box pin No. 17. If voltage is 9.5-18 volts and within .5 volt of recorded battery voltage, go to next step. If voltage is not 9.5-18 volts or is not within .5 volt of recorded battery voltage, go to step 4)
  2. Verify Code

    Turn ignition off. Reconnect control module connector. Turn ignition on. Check ABS warning light. If light is on, go to next step. If light is off, fault is intermittent. Perform INTERMITTENT DIAGNOSIS PROCEDURE  .
  3. Retrieve Codes

    Using New Generation Star (NGS) scan tool or equivalent, retrieve codes. If DTC 1185 is present, replace control module and go to step 14). If any other DTCs are present, perform appropriate circuit test.
  4. Check Fuse

    Remove and inspect 30-amp fuse No. 9, located in engine compartment fuse/relay block. If fuse is okay, go to step 7). If fuse is blown, go to next step.
  5. Check For Short To Ground

    Remove main relay. Measure resistance of Tan/Yellow wire between ground and main relay connector. If resistance is less than 10 ohms, repair short to ground in Tan/Yellow wire and go to step 14). If resistance is more than 10 ohms, go to next step.
  6. Check For Short To Ground

    Disconnect HCU 8-pin connector. Install Breakout Box (49-UN01-058) with proper overlay. Measure resistance between breakout box pin No. 17 and pins No. 1 (Orange/Yellow wire) and No. 4 (Orange/Yellow wire) at HCU connector. If resistance is less than 10 ohms, repair short to ground in Orange/Yellow wire and go to step 14). If resistance is more than 10 ohms, replace main relay and go to step 14).
  7. Check Power To Fuse

    Remove 30-amp fuse No. 9, located in engine compartment fuse/relay block. Turn ignition on. Measure voltage between ground and power side of 30-amp fuse no. 9. If battery voltage is present, go to next step. If battery voltage is not present, locate and repair open in power feed circuit and go to step 14).
  8. Check For Open Circuit

    Turn ignition off. Remove main relay. Measure resistance of Tan/Yellow wire between 30-amp fuse No. 9 and main relay harness connector. If resistance is less than one ohm, go to next step. If resistance is more than one ohm, locate and repair open in Tan/Yellow wire and go to step 14).
  9. Check For Short To Ground

    Turn ignition off. Measure resistance of Pink/Light Green wire between ground and pin No. 19 at breakout box. If resistance is less than 10 ohms, locate and repair short to ground in Pink/Light Green wire and go to step 14). If resistance is more than 10 ohms, go to next step.
  10. Check For Open Circuit

    Turn ignition off. Measure resistance of Pink/Light Green wire between main relay connector and pin No. 19 at breakout box. If resistance is less than one ohm, go to next step. If resistance is more than one ohm, locate and repair open in Pink/Light Green wire and go to step 14).
  11. Check For Open Circuit

    Turn ignition off. Measure resistance of Orange/Yellow wire between main relay connector and pin No. 17 at breakout box. If resistance is less than one ohm, go to next step. If resistance is more than one ohm, locate and repair open in Orange/Yellow wire and go to step 14).
  12. Check Relay Coil

    Remove main relay. Measure resistance between pins No. 85 (Light Blue/Pink wire) and No. 86 (Pink/Light Green wire) at main relay. If resistance is 60-80 ohms, go to next step. If resistance is not 60-80 ohms, replace relay and go to step 14).
  13. Check Voltage To Relay Coil

    Turn ignition on. Measure voltage between ground and Light Blue/Pink wire at main relay connector. If battery voltage is present, replace relay and check system operation. If battery voltage is not present, repair open in Light Blue/Pink wire and go to next step.
  14. Verify Repair

    Turn ignition off. Reconnect and reassemble all components. Install New Generation Star (NGS) scan tool or equivalent. Clear all codes. Perform step 1) of DRIVE TEST  under DIAGNOSIS & TESTING. Retrieve codes. If SYSTEM PASS is set, condition has been repaired and test is complete. If original code is set, repeat step 1). If a different code is set, perform appropriate circuit test.