Test No. 1
- Unplug harness connector from servo, located at right rear of engine compartment. Turn ignition on. Test for battery voltage between servo harness connector terminals No. 7 (Gray/Yellow wire) and No. 10 (Pink/Orange wire) at servo. If battery voltage exists, go to next step. If battery voltage does not exist, go to TEST NO. 2.
- With brake pedal in released position, test for voltage betweenservo harness connector terminals No. 4 (Tan/Light Blue wire) and No. 10 (Pink/Orange wire). If voltage is zero, stoplight switch is not stuck on. Go to next step. If battery voltage exists, replace stoplight switch.
- Turn ignition off. Measure resistance between servo harness connector terminals No. 4 (Tan/Light Blue wire) and No. 10 (Pink/Orange wire). If resistance is less than 20 ohms, go to next step. If resistance is greater than 20 ohms, repair stoplight circuit (including burnt bulbs). See WIRING DIAGRAMS .
- Turn ignition on. With brake pedal depressed, measure voltage between servo harness connector terminals No. 9 (Black/Yellow wire) and No. 10 (Pink/Orange wire). If battery voltage does not exist, go to next step. If battery voltage exists, go to step 7).
- Unplug connector from deactivator switch, located in master cylinder area. Test for voltage between Gray/Yellow wire at switch harness connector and ground. If battery voltage exists, go to next step. If battery voltage does not exist, repair open in Gray/Yellow wire from fuse panel.
- Measure resistance between Black/Yellow wire at deactivator switch connector and terminal No. 9 (Black/Yellow wire) at servo harness connector. If resistance is less than one ohm, go to next step. If resistance is greater than one ohm, repair open in Black/Yellow wire.
- With no cruise control switches pressed, measure voltage between servo harness connector terminals No. 5 (Light Blue/Black wire) and No. 10 (Pink/Orange wire). If voltage is zero, cruise control ON switch is not stuck. Go to next step. If battery voltage exists, replace cruise control ON switch.
- Measure voltage between servo harness connector terminals No. 5 (Light Blue/Black wire) and No. 10 (Pink/Orange wire) while pressing cruise control ON switch. If battery voltage exists, go to step 12). If voltage is less than battery voltage, go to next step.WARNING: Before performing following steps, deactivate air bag system. See appropriate AIR BAG RESTRAINT SYSTEM article in this section. DO NOT attempt to make any measurements at the clockspring connector before system is deactivated, air bag modules are removed, and air bag simulators are installed. DO NOT apply electrical power to any component on steering column without first deactivating air bag system. Air bag may deploy.
- Unplug clockspring connector at base of steering column. Test for voltage between Yellow/Light Green wire at harness connector and terminal No. 10 (Pink/Orange wire) of servo harness connector. If battery voltage exists, go to next step. If battery voltage does not exist, repair Yellow/Light Green wire to clockspring, or Yellow/Light Blue wire to horn relay. See WIRING DIAGRAMS .
- Disconnect negative battery cable. Unplug 5-pin connector from clockspring. Measure resistance through each clockspring circuit associated with connector just removed. If resistance is less than one ohm for each measurement, reconnect clockspring connector, reactivate air bag system, then go to next step. If any measurement exceeds one ohm, replace clockspring. See appropriate AIR BAG RESTRAINT SYSTEM article in this section.
- Unplug connector at cruise control ON/OFF switch. Turn ignition on. Test for voltage at Light Blue/Black wire at switch connector. If battery voltage exists, replace cruise control ON/OFF switch. If battery voltage does not exist, replace steering wheel wiring harness.
- With no cruise control switches pressed, measure resistance between servo harness connector terminals No. 5 (Light Blue/Black wire) and No. 6 (Dark Green/Orange wire). If resistance is greater than 3000 ohms, no switches are stuck. Go to next step. If resistance is less than 3000 ohms, replace stuck cruise control switch.
- With SET-ACCEL switch pressed, measure resistance between servo harness connector terminals No. 5 (Light Blue/Black wire) and No. 6 (Dark Green/Orange wire). If resistance is 646-714 ohms, SET-ACCEL switch is okay. Go to next step. If resistance is not 646-714 ohms, replace SET-ACCEL switch.
- With COAST switch pressed, measure resistance between servo harness connector terminals No. 5 (Light Blue/Black wire) and No. 6 (Dark Green/Orange wire). If resistance is 114-126 ohms, COAST switch is okay. Go to next step. If resistance is not 114-126 ohms, replace COAST switch.
- With RESUME switch pressed, measure resistance between servo harness connector terminals No. 5 (Light Blue/Black wire) and No. 6 (Dark Green/Orange wire). If resistance is 2090-2310 ohms, RESUME switch is okay. Go to next step. If resistance is not 2090-2310 ohms, replace RESUME switch.
- With cruise control OFF switch pressed, measure resistance between servo harness connector terminals No. 5 (Light Blue/Black wire) and No. 6 (Dark Green/Orange wire). If resistance is less than 4 ohms, cruise control OFF switch is okay. Go to next step. If resistance is 4 ohms or more, replace cruise control ON/OFF switch.
- Measure resistance between servo harness connector terminal No. 6 (Dark Green/Orange wire) and terminal No. 10 (Pink/Orange wire). If resistance is greater than one ohm, go to next step. If resistance is one ohm or less, repair short on Dark Green/Orange wire.
- Measure resistance between servo harness connector terminals No. 3 (Gray/Black wire) and No. 10 (Pink/Orange wire). If resistance is not 200-300 ohms, go to next step. If resistance is 200-300 ohms, go to step 20).
- Unplug Vehicle Speed Sensor (VSS) connector, threaded into transmission (2WD), or into transfer case (4WD). Measure resistance between sensor terminals. If resistance is 200-300 ohms, repair wiring between VSS and servo. If resistance is not 200-300 ohms, replace VSS.
- Road test vehicle. Observe speedometer. If pointer does not waver, go to next step. If pointer wavers, replace VSS.
- Disengage cable from servo. Inspect for broken cable by pulling end of cable and observing throttle movement. Replace cable if necessary. If cable is okay, replace servo.