LEMON Manuals: Even more car manuals for everyone
Home >> Lincoln >> 2011 >> Navigator 4WD >> Repair and Diagnosis >> Accessories & Equipment >> Communication Devices >> Module Communications Network >> Diagnosis And Testing >> Communications Network >> Inspection and Verification

Inspection and Verification

  1. Verify the customer concern.
  2. Visually inspect for obvious signs of electrical damage.
    • If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
    VISUAL INSPECTION CHART

    Electrical
    • Battery Junction Box (BJB) fuse(s):
      • 11 (40A) (no communication with PRB  module)
      • 20 (20A) (no communication with 4X4 control module)
      • 26 (15A) (no communication with TCM  )
      • 27 (20A) (no communication with 4X4 control module)
      • 36 (30A) (no communication with LTM  )
      • 41 (10A) (no communication with PCM)
      • 48 (30A) (no communication with VDM  )
      • 52 (10A) (no communication with ABS module)
      • 53 (10A) (no communication with VDM  )
      • 54 (5A) (no communication with TCM  )
      • 55 (5A) (no communication with PCM)
      • 67 (40A) (no communication with DSCM  )
      • 68 (60A) (no communication with ABS module)
      • 69 (60A) (no communication with ABS module)
      • 75 (20A) (no communication with PCM)
    • Smart Junction Box (SJB) fuse(s):
      • 2 (15A) (no communication with DSM  )
      • 3 (15A) (no communication with APIM  , SDARS  module, audio RCU  module)
      • 5 (10A) (no communication with SJB  )
      • 14 (10A) (no communication with LTM  )
      • 15 (10A) (no communication with HVAC module and GPSM  )
      • 20 (15A) (no power to the scan tool)
      • 26 (10A) (no communication with IC  )
      • 29 (5A) (no communication with IC  )
      • 32 (10A) (no communication with RCM  )
      • 35 (10A) (no communication with PAM  and 4X4 control module)
      • 37 (10A) (no communication with HVAC module)
      • 38 (20A) (no communication with audio DSP  module)
      • 39 (20A) (no communication with ACM  )
      • 40 (20A) (no communication with audio DSP  module)
    • Data Link Connector (DLC)
    • Wiring harness
    • Wiring, terminals or connectors
  3. Connect the scan tool to the DLC  .
      NOTE: Make sure to use the latest scan tool software release.
      NOTE: The Vehicle Communication Module (VCM) LED prove-out confirms power and ground from the DLC  are provided to the VCM  .
    • If the Integrated Diagnostic System (IDS) does not communicate with the VCM :
      • Check the VCM connection to the vehicle.
      • Check the scan tool connection to the VCM  .
      • Go to PINPOINT TEST Y , to diagnose No Power To The Scan Tool.
  4. Establish a scan tool session.
      NOTE: The scan tool first attempts to communicate with the PCM, after establishing communication with the PCM, the scan tool then attempts to communicate with all other modules on the vehicle.
    • If an IDS session cannot be established with the vehicle, (IDS may state "No communication can be established with the PCM"):
      • Choose "NO" when the scan tool prompts whether or not to retry communication.
      • Enter either a PCM part number, tear tag or calibration number to identify the vehicle and start a session (the PCM part number and 4-character tear tag are printed on the PCM label).
      • Go to PINPOINT TEST A , to diagnose The PCM Does Not Respond To The Scan Tool.
  5. Carry out the network test.
    • If the network test passes, retrieve and record the continuous memory DTCs and proceed to Step 6.
    • If the network test fails, go to SYMPTOM CHART  to diagnose the failed communication network.
    • If a module fails to communicate during the network test, go to SYMPTOM CHART .
  6. Retrieve and review the DTCs.
    • If the DTCs retrieved are related to the concern, go to DTC CHARTS . Follow the non-network DTC diagnostics (B-codes, C-codes, P-codes) prior to the network DTC diagnostics (U-codes). For all other DTCs, refer to MULTIFUNCTION ELECTRONIC MODULE .
    • If no DTCs related to the concern are retrieved, go to SYMPTOM CHART .