LEMON Manuals: Even more car manuals for everyone
Home >> Lincoln >> 2002 >> Navigator 4WD >> Repair and Diagnosis >> External Pages >> Different car >> Section 357 (Engine - 4.6L & 5.4L) >> Specifications >> General Specifications

General Specifications

WARNING: This page is about a different car, the 2002 Ford Expedition. However, it is still accessible from the selected car via links, so may be relevant.
GENERAL SPECIFICATIONS (SEALANTS & LUBRICANTS)

Item Specification
Silicone Gasket and Sealant F7AZ-19554-EA WSE-M4G323-A4
Metal Surface Cleaner F4AZ-19A536-RA WSE-M5B392-A
Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10). Do not mix coolant types. ESE-M97B44-A (Green in color)
Motorcraft Premium Gold Engine Coolant VC-7-A. Do not mix coolant types. WSS-M97B51-A1 (Yellow in color)
Super Premium SAE 5W-20 Motor Oil XO-5W20-QSP WSS-M2C153-H
Petroleum Jelly WSD-M1C226-A
High Temperature Nickel Anti-Seize Lubricant F6AZ-9L494-AA ESE-M12A4-A
GENERAL SPECIFICATIONS (ENGINE 4.6L)

Item Specification
Displacement L (CID) 4.6 (281)
Number of cylinders 8
Bore and stroke mm 90.2 x 90.0
Firing order 1-3-7-2-6-5-4-8
Oil pressure (HOT @ 1500 rpm) kPa 138-310
Drive belt tension (1)
Cylinder head and valve train 
Combustion chamber volume cm 52+/-.5
Valve seats width - intake mm 1.9-2.1
Valve seats width - exhaust mm 1.9-2.1
Valve seats angle 44.51-45.01 degrees
Valve seats runout (T.I.R.) max mm 0.025
Valve arrangement (front-to-rear) (Left Hand) E-I-E-I-E-I-E-I (Right Hand) I-E-I-E-I-E-I-E
Valve stem to guide clearance - intake mm (inch) 0.020-0.069 (0.00079-0.00272)
Valve stem to guide clearance-exhaust mm (inch) 0.046-0.095 (0.0018-0.0037)
Valve head diameter - intake mm (inch) 44.5- (1.75)
Valve head diameter - exhaust mm (inch) 34.0 (1.34)
Valve head diameter - gauge diameters mm (inch) 42.5 - and 32.0 (1.67 and 1.26)
Valve face runout limit mm (inch) 0.05 (0.002)
Valve face angle 45.25-45.75 degrees
Valve stem diameter (Std) - intake mm (inch) 6.995-6.975 (0.275-0.2746)
Valve stem diameter (Std) - exhaust mm (inch) 6.970-6.949 (0.274-0.2736)
Valve springs - compression pressure N @ spec. length - intake 587.14 N @ 28.02 mm
Valve springs - compression pressure N @ spec. length - exhaust 587.14 N @ 28.02 mm
Valve springs - free length (approximate) - intake mm (inch) 49.55 (1.951)
Valve springs - free length (approximate)-exhaust mm (inch) 49.55 (1.951)
Valve springs - installed pressure N @ spec. length - intake 244.64 N @ 40.0 mm
Valve spring - installed pressure N @ spec. length - exhaust 244.64 N @ 40.0 mm
Valve springs - installed pressure N @ spec. length - service limit 10 % pressure less @ 28.02 mm
Valve springs - installed pressure N @ spec. length - out of square limit 2 degrees
Valve guide inner diameter mm (inch) 7.015-7.044 (0.2761-0.2773)
Rocker arm - ratio 1.75:1
Valve tappet - diameter (Std) mm (inch) 16.000-15.988 (0.66-0.629)
Valve tappet - clearance to bore mm (inch) 0.018-0.069 (0.00071-0.00272)
Valve tappet - service limit mm (inch) 0.016 (0.00063)
Valve tappet - hydraulic leakdown rate (2) 5-25 seconds
Valve tappet - collapsed valve tappet gap-desired mm (inch) 0.085-0.45 (0.0033-0.0177)
Camshaft 
Lobe lift - intake mm (inch) 6.58939 (0.2594)
Lobe lift - exhaust mm (inch) 6.58939 (0.2594)
Lobe lift - allowable lobe lift loss mm (inch) 0
Theoretical valve lift @ zero lash - intake mm (inch) 12.0 (0.472)
Theoretical valve lift @ zero lash - exhaust mm (inch) 12.0 (0.472)
End play mm (inch) 0.025-0.165 (0.00098-0.0065)
Journal to bearing clearance mm (inch) 0.025-0.076 (0.00098-0.003)
Journal to bearing clearance - service limit mm (inch) 0.021 (0.0048)
Journal diameter (all) mm (inch) 26.962-26.936 (1.061-1.060)
Journal diameter (all) - bearing inside diameter (all) mm (inch) 27.012-26.987 (1.063-1.0625)
Camshaft runout mm (inch) 0.05 (0.002)
Cylinder Bore 
Diameter - surface finish (RMS) 0.2-0.6 microns
Diameter - out-of-round limit mm (inch) 0.015 (0.0006)
Diameter - out-of-round service limit mm (inch) 0.020 (0.00079)
Diameter - taper service limit mm (inch) 0.006 (0.00023)
Piston 
Piston - diameter-coded Red 1 mm (inch) 90.177-90.197 (3.550-3.551)
Piston - diameter-coded Blue 2 mm (inch) 90.190-90.210 (3.5507-3.5515)
Piston - diameter - coded Yellow 3 mm (inch) 90.203-90.223 (3.513-3.5521)
Piston-to-bore clearance mm (inch) -0.015 - +0.031 (0.0005-0.0012)
Pin bore diameter mm (inch) 22.0015-22.004 (0.866-0.8663)
Ring groove width - compression (top) mm (inch) 1.520-1.550 (0.06-0.610)
Ring groove width - compression (bottom) mm (inch) 1.520-1.530 (0.060-0.0602)
Ring groove width - oil ring mm (inch) 6.996-7.224 (0.275-0.2844)
Piston pin - length mm (inch) 61.93-62.05 (2.44-2.443)
Diameter mm (inch) 21.994-21.999 (0.866-0.8661)
Pin to piston clearance mm (inch) 0.005-0.010 (0.0002-0.0004)
Pin to rod clearance mm (inch) 0.015-0.040 (0.0006-0.00157)
Piston rings - ring gap - compression (top) mm (inch) 1.0 Max (0.0394)
Piston rings - ring gap - compression (top) mm (inch) 1.0 Max (0.0394)
Oil ring - side clearance mm (inch) 1.25 Max (0.05)
Oil ring - compression (top) mm (inch) 0.040-0.090 (0.0016-0.0031)
Oil ring - compression (top) mm (inch) 0.030-0.080 (0.0012-0.00031)
Oil ring Snug fit
Oil ring - service limit mm (inch) 0.015 Max (0.0006)
Ring gap - compression (top) mm (inch) 0.23-0.49 (0.01-0.02)
Ring gap - compression (bottom) mm (inch) 0.23-0.49 (0.01-0.02)
Ring gap - oil ring (steel rail) mm (inch) 0.05-0.66 (0.006-0.026)
Lubrication System 
Oil capacity - automatic transmission (quarts U.S.) 6.675+/-0.125
Oil capacity - manual transmission (quarts U.S.) 6.425+/-0.125
Cylinder Block 
Main bearing bore diameter mm (inch) 72.401-72.422 (2.85-2.851)
Crankshaft and Flywheel 
Main bearing journal diameter mm (inch) 67.483-67-503 (2.65-2.657)
Connecting rod journal - diameter mm (inch) 52.988-53.003 (2.0861-2.0867)
Crankshaft free end play mm (inch) 0.130-0.301 (0.0051-0.012)
Crankshaft runout to rear face of block mm (inch) 0.050 Max (0.002)
Connecting Rod Bearings 
Clearance to crankshaft - desired mm (inch) 0.027-0.069 (0.001-0.0027)
Clearance to crankshaft - allowable mm (inch) 0.027-0.069 (0.001-0.0027)
Bearing wall thickness (Std) mm (inch) 2.44-2.452 (0.096-0.0965)
Main Bearings 
Clearance to crankshaft - desired mm (inch) 0027-0.065 (0.0011-0.0026)
Clearance to crankshaft - allowable mm (inch) 0.027-0.065 (0.0011-0.0026)
Bearing wall thickness (Std) mm (inch) 1.920-1.928 (0.075-0.076)
Connecting Rod, Piston and Rings 
Connecting rod-piston pin bore diameter mm (inch) 21.959-21.979 (0.864-0.865)
Connecting rod - crankshaft bearing bore diameter mm (inch) 56.756-56.876 (2.234-2.24)
Connecting rod - length (center-to-center) mm (inch) 150.7 (5.93)
Alignment (bore-to-bore Max. Diff.) (3) - Twist mm (inch) 0.050 per 25 (0.0015-0.984)
Alignment (bore-to-bore Max. Diff.) - bend mm (inch) 0.038 per 25 (0.0015-0.984)
Side clearance (assembled to crank) - standard mm (inch) 0.015-0.45 (0.0006-0.0177)
Side clearance (assembled to crank) - service limit mm (inch) 0.05 Max (0.02)
Crankshaft main bearing journal taper mm (inch) 0.020 (0.0007)
Crankshaft main bearing journal runout mm (inch) 0.05 (0.002)
Crankshaft connecting rod journal taper mm (inch) 0/015 (0.0005)
(1) Newly installed - Refers to the condition of the NEW drive belt before the engine has made no more than one rotation and before the belt has had a chance to stretch or seat into the pulley grooves.
(2) Time required for the plunger to leak down 1.6 mm of travel with 222 N force and leak-down fluid in tappet.
(3) The pin bore and crank bearing bore must be parallel and in the same vertical plane within the specified total difference when measured at the ends of a 203 mm bar, 105.5 mm on each side of rod centerline.
GENERAL SPECIFICATIONS (ENGINE 5.4L)

Item Specification
Displacement 5.4L
No. cylinder 8
Bore/stroke 90.215/105.8 mm
Fire order 1-3-7-2-6-5-4-8
Oil pressure (HOT @ 2000 rpm) 275.8-413.7 kPa
Cylinder Head/Valve Train 
Combustion chamber volume 43.95 +/- 1.5 cc
Valve seat width - intake 1.3-1.5 mm
Valve seat width - exhaust 2.1-1.9 mm
Valve seat angle 45.00-44.50 degrees
Valve seat runout (T.I.R.) 0.025 mm
Valve Arrangement (Front to Rear) 
Valve stem guide clearance Intake 0.069-0.020 mm
Exhaust 0.095-0.045 mm
Valve head diameter Intake 44.63-44.37 mm
Exhaust 34.12-33.88 mm
Valve face runout (limit) 0.05 mm
Valve face angle 45.75-45.25 degrees
Valve stem diameter Intake 6.995-6.975 mm
Exhaust 6.970-6.949 mm
Valve stem diameter (list oversizes) Intake N/A
Exhaust N/A
Valve spring compression pressure Intake (N @ spec. length) 720-800 N @ 28.02 mm
Exhaust (N @ spec. length) 720-800 N @ 28.02 mm
Valve spring free length Intake 53.37 mm
Exhaust 53.37 mm
Valve spring installed pressure N @ spec. length Intake 287.19-321.19 N @ 42.56 mm
Exhaust 287.19-321.19 N @ 42.56 mm
Valve springs installed pressure N @ spec. length-service limit Intake 5% pressure loss @ 28.80 mm
Exhaust 5% pressure loss @ 28.80 mm
Valve springs - out of square limit Intake 2.0 degrees
Exhaust 2.0 degrees
Valve guide inside diameter 7.044-7.015 mm
Hydraulic Lash Adjuster 
Diameter mm (inch) 16.000-15.988 (0.66-0.629)
Clearance-to-bore mm (inch) 0.018-0.069 (0.00071-0.00272)
Service limit mm (inch) 0.016 (0.00063)
Hydraulic leakdown rate (1) 5-25 seconds
Collapsed lash adjuster gap - desired mm (inch) 0.085-0.45 (0.0033-0.0177)
Camshaft 
Lobe lift Exhaust 7.49744 mm
Intake 7.11038 mm
Lobe lift - allowable lift loss 0
Valve lift @ zero lash Intake 13.01 mm
Exhaust 13.75 mm
Camshaft end play 0.027-0.190 mm
End play service limit 0.025-0.190 mm
Journal to bearing clearance 0.076-0.025 mm
Clearance service limit -
Journal diameters 26.962-26.936 mm
Journal inside diameter (cap assembled) 27.012-26.987 mm
Camshaft runout: Full indicator measurement on all journals when supported on front and rear journals. (4 places) 0.03 mm
Cylinder bore diameter Grade 1 90.200-90.210 mm
Grade 2 90.210-90.220 mm
Grade 3 90.220-90.230 mm
Piston 
Piston diameter (Grade 2) at right angle to pin bore 90.180 +/- 0.005
Piston to bore clearance -0.005 - +0.025 mm (0.0002-0.0010 in)
Pin bore diameter (piston) 21.999-22.004 mm
Pin diameter 21.9915-21.9935 mm
Clearance 0.00585-0.01242 mm
Pin bore diameter (rod) 22.012-22.024 mm
Clearance 0.0185-0.325 mm
Ring groove width Top 1.53-1.55 mm
Intermediate 1.52-1.54 mm
Oil control 3.030-3.050 mm
Piston ring gap Top 0.13-0.28 mm
Intermediate 0.25-0.40 mm
Oil control 0.15-0.65 mm
Crankshaft 
Main bearing journal diameter Maximum out-of-round 67.483-67.503 mm 0.0075 mm between cross sections
Maximum taper (straightness) 0.004 mm
Runout: FIM of center journals when located on front and rear journal 0.05 mm (3 places)
Clearance - crankshaft journal to main bearing clearance 0.048-0.024 mm
Connecting rod journal diameter 53.003-52.983 mm
Maximum out-of-round 0.0075 mm between cross
Maximum taper Sections 0.004 mm
Crankshaft end play 0.075-0.377 mm
Connecting Rod 
Big end journal inside diameter with assembled liners 53.049-53.027 mm
Rod bearing to journal clearance 0.064-0.026 mm
Pin bore diameter (rod) 22.024-22.012 mm
Rod length (centerline bore-to-bore) 169.1 mm
Alignment Bore-to-bore Max. twist +/- 0.05 mm
Bore-to-bore Max. bend +/- 0.038 mm
Side play (as assembled to crank) Standard play 0.300 +/- 0.175 mm
(1) Time required for the plunger to leak down 1.6 mm of travel with 222 N force and leak-down fluid in tappet.