Test E: Single Mirror Inoperative
- Using NGS tester, perform Driver's Door Module (DDM) self-test. Retrieve DTCs. If no DTCs exist, go to next step. If DTC B2336 exists, go to step 30 . If DTC B2330 or B2324 exists, go to step 20 . If any other DTCs exist, see MODULE COMMUNICATIONS NETWORK - LS article for complete DTC listing.
- Using NGS tester, perform Front Electronics Module (FEM) self-test. Retrieve DTCs. If no DTCs exist, go to next step. If DTC B2312 or B2316 exist, go to step 5 . If any other DTCs exist, see MODULE COMMUNICATIONS NETWORK - LS article for complete DTC listing.
- Using NGS tester, monitor DDM PIDs MIRH_SW, MIRV_SW and MIR_SEL while operating mirror control switch in each direction. If DDM PID values agree with mirror control switch positions, go to next step. If DDM PID values do not agree with mirror control switch positions, go to step 18 .
- Operate driver's and passenger's mirrors. If driver's mirror operates properly and passenger's mirror is inoperative, go to next step. If passenger's mirror operates properly and driver's mirror is inoperative, go to step 20 .
- Remove fuse No. 406 (10-amp) from Battery Junction Box (BJB). Measure voltage between ground and BJB fuse No. 406 power input supply terminal (Red/Orange wire). See Fig 1 . If more than 10 volts exists, go to next step. If 10 volts or less exists, repair open in Red/Orange wire. See WIRING DIAGRAMS .
- Reinstall fuse No. 406. Turn ignition switch to LOCK position. Disconnect FEM 17-pin harness connector C201A. Turn ignition switch to RUN position. Measure voltage between ground and FEM harness connector C201A terminal No. 1 (Orange/White wire). See Figure . If more than 10 volts exists, go to next step. If 10 volts or less exists, repair open in Orange/White wire between CJB and FEM. See WIRING DIAGRAMS .
- Using NGS tester, select POWER MIRROR CONTROL from FEM active command menu. Trigger FEM active commands PR UP, PR DOWN, PR LEFT and PR RIGHT ON and OFF. If passenger's mirror does not operate properly, go to next step. If passenger's mirror operates properly, go to step 14 .
- Turn ignition to LOCK position. Disconnect passenger's side mirror 20-pin harness connector C601. Turn ignition switch to RUN position. Measure voltage between ground and passenger's side mirror harness connector C601 terminals as specified. See PASSENGER'S MIRROR TERMINAL IDENTIFICATION
table. See Fig 2
. If 10 volts or less exists at all terminals, go to next step. If more than 10 volts exists at any terminals, go to step 12
.PASSENGER'S MIRROR TERMINAL IDENTIFICATION
Terminal No. Wire Color Mirror Position 2 White/Black Left 4 Yellow/Black Right 6 Violet/White Down 8 Blue/Orange Up - Turn ignition switch to LOCK position. Measure resistance between ground and passenger's side mirror connector C601 terminals as specified. See PASSENGER'S MIRROR TERMINAL IDENTIFICATION table. See Fig 2 . If resistance is 5 ohms or greater, go to next step. If resistance is less than 5 ohms, go to step 13 .
- Turn ignition switch to RUN position. Measure voltage between ground and passenger's side mirror connector C601 terminals as specified with mirror control switch in appropriate position. See PASSENGER'S MIRROR TERMINAL IDENTIFICATION table. See Fig 2 . If 10 volts or less exists at any terminals, go to next step. If more than 10 volts exists at all terminals, replace passenger's mirror motor.
- Turn ignition switch to LOCK position. Disconnect FEM 26-pin harness connector C201E. Measure resistance in circuits between FEM harness connector C201E terminals and passenger's side mirror harness connector C601 terminals as specified. See PASSENGER'S MIRROR CIRCUIT IDENTIFICATION
table. See Figure
and Fig 2
. If all resistances are less than 5 ohms, replace FEM. If any resistance is 5 ohms or greater, repair open or high resistance in appropriate wire. See WIRING DIAGRAMS
.PASSENGER'S MIRROR CIRCUIT IDENTIFICATION
Mirror Terminal No. Wire Color FEM Terminal No. 2 White/Black 23 4 Yellow/Black 24 6 Violet/White 21 8 Blue/Orange 20 - Turn ignition switch to LOCK position. Disconnect FEM 26-pin harness connector C201E. Turn ignition switch to RUN position. Measure voltage between ground and passenger's side mirror harness connector C601 terminals as specified. See PASSENGER'S MIRROR TERMINAL IDENTIFICATION table. See Fig 2 . If voltage does not exist at all terminals, replace FEM. If voltage exists at any terminal(s), repair short to power in appropriate wire(s). See WIRING DIAGRAMS .
- Turn ignition switch to LOCK position. Disconnect FEM 26-pin harness connector C201E. Measure resistance between ground and FEM harness connector C201E terminals as specified. See PASSENGER'S MIRROR CIRCUIT IDENTIFICATION table. See Fig 2 . If any resistance is less than 10 k/ohms, repair short to ground in appropriate wire. See WIRING DIAGRAMS . If all resistances are 10 k/ohms or greater, replace FEM.
- Turn ignition switch to RUN position. Using NGS tester, select POWER MIRROR CONTROL from FEM active command menu. Trigger FEM active commands PR UP, PR DOWN, PR LEFT and PR RIGHT while monitoring FEM PIDs MIRH_SW and MIRV_SW. If FEM PID values do not agree with commanded mirror positions, go to next step. If FEM PID values agree with commanded mirror positions, replace FEM.
- Turn ignition switch to LOCK position. Disconnect passenger's side mirror 20-pin harness connector C601. Disconnect FEM 26-pin harness connector C201E. Turn ignition switch to RUN position. Measure voltage between ground and passenger's mirror harness connector C601 terminals as specified. See PASSENGER'S SIDE MIRROR TERMINAL IDENTIFICATION
table. See Fig 2
. If voltage does not exist at any terminal, go to next step. If any voltage exists at any terminal, repair short to power in appropriate wire. See WIRING DIAGRAMS
.PASSENGER'S SIDE MIRROR TERMINAL IDENTIFICATION
Terminal No. Wire Color 1 White/Red 3 Brown/Red 5 Gray/Red 7 Yellow/Red - Turn ignition switch to LOCK position. Measure resistance between ground and passenger's side mirror harness connector C601 terminals as specified. See PASSENGER'S SIDE MIRROR TERMINAL IDENTIFICATION table. See Fig 2 . If resistances are greater than 10 k/ohms, go to next step. If resistance is 10 k/ohms or less, repair short to ground in appropriate wire. See WIRING DIAGRAMS .
- Measure resistance in circuits between FEM harness connector C201E and passenger's side mirror harness connector C601 terminals as specified. See FEM CIRCUIT IDENTIFICATION
table. See Figure
and Fig 2
. If all resistances are less than 5 ohms, replace passenger's side mirror. If any resistances is 5 ohms or greater, repair open or high resistance in appropriate wire. See WIRING DIAGRAMS
.FEM CIRCUIT IDENTIFICATION
Mirror Terminal No. Wire Color FEM Terminal No. 1 White/Red 7 3 Brown/Red 22 5 Gray/Red 11 7 Yellow/Red 8 - Remove mirror control switch. Test mirror control switch. See MIRROR CONTROL SWITCH under COMPONENT TESTS. If mirror control switch is okay, go to next step. If mirror control switch is not okay, replace mirror control switch.
- Turn ignition switch to LOCK position. Disconnect mirror control switch 10-pin harness connector C204. Disconnect DDM 26-pin harness connector C501D. Measure resistance in circuits between mirror control switch harness connector C204 and DDM harness connector C501D as specified. See DDM CIRCUIT IDENTIFICATION
table. See Figure
and Fig 2
. If resistances are less than 5 ohms, replace DDM. If any resistance is 5 ohms or greater, repair open or high resistance in appropriate wire. See WIRING DIAGRAMS
.DDM CIRCUIT IDENTIFICATION
Mirror Control Switch Terminal No. Wire Color DDM Terminal No. 1 White/Black 15 2 White/Red 17 8 Blue/White 16 9 Blue/Orange 14 - Remove fuse No. 222 (10-amp) from Central Junction Box (CJB). See Fig 3 . Measure voltage between ground and CJB fuse No. 222 input side (power supply). If more than 10 volts exists, go to next step. If 10 volts or less exists, repair open in Red/Orange wire between CJB and BJB. See WIRING DIAGRAMS .
- Turn ignition switch to LOCK position. Reinstall fuse No. 222. Disconnect DDM 12-pin harness connector C501A. Turn ignition switch to RUN position. Measure voltage between ground and DDM harness connector C501A terminal No. 12 (Orange/Blue wire). See Figure . If more than 10 volts exist, go to next step. If 10 volts or less exists, repair open in Orange/Blue wire between CJB and DDM. See WIRING DIAGRAMS .
- Using NGS tester, select POWER MIRROR CONTROL from DDM active command menu. Trigger DDM active command DR UP, DR DOWN, DR LEFT and DR RIGHT ON and OFF. If driver's side mirror does not operate properly, go to next step. If driver's side mirror operates properly, go to step 27 .
- Turn ignition switch to LOCK position. Disconnect driver's side mirror 20-pin harness connector C520. Turn ignition switch to RUN position. Measure voltage between ground and driver's mirror harness connector C520 terminals as specified. See DRIVER'S SIDE MIRROR TERMINAL IDENTIFICATION
table. See Fig 2
. If 10 volts or less at all terminals, go to next step. If more than 10 volts exists at any terminal, go to step 31
. See WIRING DIAGRAMS
.DRIVER'S SIDE MIRROR TERMINAL IDENTIFICATION
Terminal No. Wire Color Mirror Position 2 White/Red Left 4 Yellow/Red Right 6 Violet Down 8 Blue/White Up - Turn ignition switch to RUN position. Measure voltage between ground and driver's side mirror harness connector C520 terminals as specified while operating mirror control switch to appropriate positions. See DRIVER'S SIDE MIRROR TERMINAL IDENTIFICATION table. See Fig 2 . If 10 volts or less exists at any terminal, go to next step. If more than 10 volts exists at all terminals, replace driver's mirror motor.
- Turn ignition switch to LOCK position. Disconnect DDM 20-pin harness connector C501C. Turn ignition switch to RUN position. Measure resistance in circuits between DDM harness connector C501C and driver's side mirror harness connector C520 as specified. See DRIVER'S SIDE MIRROR CIRCUIT IDENTIFICATION
table. See Fig 2
. If resistances are less than 5 ohms, go to next step. If any resistance is 5 ohms or more, repair open or high resistance in appropriate wire.DRIVER'S SIDE MIRROR CIRCUIT IDENTIFICATION
Mirror Terminal No. Wire Color DDM Terminal No. 2 White/Red 1 4 Yellow/Red 2 6 Violet 4 8 Blue/White 3 - Turn ignition switch to LOCK position. Measure resistance between ground and driver's mirror harness connector C520 terminals as specified. See DRIVER'S SIDE MIRROR TERMINAL IDENTIFICATION table. See Fig 2 . If all resistances are 10 k/ohms or greater, replace DDM. If resistance is 10 k/ohms or less at any terminal, repair short to ground in appropriate wire. See WIRING DIAGRAMS .
- Using NGS tester, select POWER MIRROR CONTROL from DDM active command menu. Trigger DDM active command DR UP, DR DOWN, DR LEFT and DR RIGHT ON and OFF while monitoring DDM PIDs MIRH_SW and MIRV_SW. If PID values do not agree with driver's commanded mirror positions, go to next step. If PID values agree with driver's commanded mirror positions, replace DDM.
- Turn ignition switch to LOCK position. Disconnect driver's side mirror 20-pin harness connector C520. Disconnect DDM 20-pin harness connector C501C. Measure voltage between ground and driver's side mirror harness connector C520 terminals as specified. See DRIVER'S SIDE MIRROR TERMINAL IDENTIFICATION
table. See Fig 2
and Fig 4
. If voltage does not exist at any terminal, go to next step. If voltage exists at any terminal, repair short to power in appropriate wire. See WIRING DIAGRAMS
.DRIVER'S SIDE MIRROR TERMINAL IDENTIFICATION
Terminal No. Wire Color 1 White/Black 3 Brown/Yellow 5 Gray/Black 7 Yellow/Black - Turn ignition switch to LOCK position. Measure resistance between ground and driver's side mirror harness connector C520 terminals as specified. See DRIVER'S MIRROR TERMINAL IDENTIFICATION table. See Fig 2 . If all resistances are greater than 10 k/ohms, go to next step. If any resistance is 10 k/ohms or less, repair short to ground in appropriate wire. See WIRING DIAGRAMS .
- Turn ignition switch to LOCK position. Disconnect driver's side mirror 20-pin harness connector C520. Disconnect DDM 20-pin harness connector C501C. Measure resistance in circuits between DDM harness connector C501C and driver's side mirror harness connector C520 as specified. See DRIVER'S SIDE MIRROR CIRCUIT IDENTIFICATION
. See Fig 2
and Fig 4
. If all resistances are less than 5 ohms, replace driver's side mirror. If any resistance is 5 ohms or greater, repair open or high resistance in appropriate wire. See WIRING DIAGRAMS
.DRIVER'S SIDE MIRROR CIRCUIT IDENTIFICATION
Mirror Terminal No. Wire Color DDM Terminal No. 1 White/Black 14 3 Brown/Yellow 19 5 Gray/Black 15 7 Yellow/Black 5 - Turn ignition switch to LOCK position. Disconnect driver's side mirror 20-pin harness connector C520. Disconnect DDM 20-pin harness connector C501C. Measure voltage between ground and driver's mirror harness connector C520 terminals as specified. See DRIVER'S SIDE MIRROR CIRCUIT IDENTIFICATION . See Fig 2 and Fig 4 . If more than 10 volts exists at any terminal, repair short to power in appropriate wire. If 10 volts or less exists at all terminals, replace DDM.
NOTE:
Cycle ignition switch from LOCK to RUN position to enable Switched System Power (SSP) feature.