LEMON Manuals: Even more car manuals for everyone
Home >> Lincoln >> 1998 >> Town Car Signature >> Repair and Diagnosis >> Body & Frame >> Mirrors >> Power Memory Mirror System >> System Tests >> Test A: No Communication With Driver Door Module (DDM)

Test A: No Communication With Driver Door Module (DDM)

NOTE: Many test steps refer to various connectors. To identify connectors use illustrations. See Figure -Figure .
NOTE: After repairs are complete, ensure all component are properly installed and all harness connectors are connected properly and repeat data link diagnostic test.
  1. Ensure transmission is in Park. Turn ignition switch to LOCK position. Check fuse No. 30 (7.5-amp) in instrument panel fuse box. If fuse is okay, go to next step. If fuse is blown, go to step 5).
  2. Measure voltage at input side of fuse No. 30. If battery voltage exists, go to next step. If battery voltage does not exist, go to step 20).
  3. Disconnect DDM harness connector C520. Measure resistance in Light Green/Purple wire between terminal No. 29 at DDM harness connector C520 and output side of fuse No. 30. If resistance is 5 ohms or less, go to next step. If resistance is greater than 5 ohms, repair open in Light Green/Purple wire between instrument panel fuse box and DDM.
  4. Measure resistance between ground and terminal No. 23 (Pink/Orange wire) at DDM harness connector C520. If resistance is greater than 5 ohms, repair open in Pink/Orange wire. If resistance is 5 ohms or less, repair module communications concern. See MODULE COMMUNICATIONS NETWORK - TOWN CAR article.
  5. Replace fuse No. 30. DO NOT operate power seat switch. If fuse blows, go to next step. If fuse does not blow, go to step 9).
  6. Remove fuse No. 30. Disconnect DDM harness connector C520 and Driver Seat Module (DSM) harness connector C313. Measure resistance between ground and terminal No. 29 (Light Green/Purple wire) at DDM harness connector C520. If resistance is 10,000 ohms or less, go to next step. If resistance is greater than 10,000 ohms, go to step 8).
  7. Test driver and passenger door lock switches. Test remote trunk lock switch. Test mirror switch. Test seat control switches. See appropriate test under COMPONENT TESTING. If no switch is defective, repair short to ground in Light Green/Purple wire. If any switch is defective, replace appropriate switch.
  8. Connect DSM harness connector C313. Measure resistance between ground and terminal No. 29 (Light Green/Purple wire) at DDM harness connector C520. If resistance is 10,000 ohms or greater, replace driver door module. If resistance is less than 10,000 ohms, replace driver seat module.
  9. Lock and unlock doors at all door lock switches. If fuse No. 30 blows, go to next step. If fuse No. 30 does not blow, go to step 12).
  10. Remove door lock switches. Test all door lock switches. See DOOR LOCK SWITCH under COMPONENT TESTING. If all door lock switches are okay, go to next step. If any door lock switch is defective, replace appropriate door lock switch.
  11. Disconnect Driver Door Module (DDM) harness connector C520. Disconnect driver door lock switch harness connector C503. Disconnect passenger door lock switch harness connector C603. Measure resistance between ground and terminal No. 2 (Pink/Yellow wire) at driver door lock switch harness connector C503. Also, measure resistance between ground and terminal No. 6 (Pink/Light Green wire) at driver door lock switch harness connector C503. If either or both resistance reading are less than 10,000 ohms, repair short to ground in appropriate wire(s). If both resistance readings are 10,000 ohms or greater, replace driver door module.
  12. Activate mirrors in all directions. If fuse No. 30 blows, go to next step. If fuse No. 30 does not blow, go to step 15).
  13. Remove mirror control switch. Test mirror control switch. See MIRROR CONTROL SWITCH under COMPONENT TESTING. If mirror control switch is okay, go to next step. If mirror control switch is defective, replace mirror control switch.
  14. Disconnect Driver Door Module (DDM) harness connector C520. Disconnect mirror control switch harness connector C550. Measure resistance between ground and appropriate terminals at DDM harness connector C520. See MIRROR CONTROL SWITCH TERMINAL IDENTIFICATION table. If all resistance readings are 10,000 ohms or greater, replace driver door module. If any resistance reading are less than 10,000 ohms, repair short to ground in appropriate wire.
    MIRROR CONTROL SWITCH TERMINAL IDENTIFICATION

    Terminal No. Wire Color
    18 Yellow/Black
    19 Dark Blue/Orange
    30 Red/Orange
    31 Purple/Orange
    32 Dark Green/Orange
  15. Activate memory switch through all positions. If fuse No. 30 blows, go to next step. If fuse No. 30 does not blow, go to step 18).
  16. Remove memory switch. Test memory switch. See DRIVER SEAT CONTROL SWITCH (WITH MEMORY) under COMPONENT TESTS. If memory switch is okay, go to next step. If memory switch is defective, replace memory switch.
  17. Disconnect Driver Door Module (DDM) harness connectors C520 and C521. Measure resistance between ground and appropriate terminals at driver seat control switch harness connector C509. See SEAT SWITCH CIRCUIT TERMINAL IDENTIFICATION table. If all resistance readings are 10,000 ohms or greater, replace driver door module. If any resistance readings are less than 10,000 ohms, repair short to ground in appropriate wire.
    SEAT SWITCH CIRCUIT TERMINAL IDENTIFICATION

    Terminal No. Wire Color
    4 White/Orange
    5 Brown/Orange
    6 Brown/Light Green
    7 Black/Orange
  18. Activate driver seat control switch in all directions. If fuse No. 30 blows, go to next step. If fuse No. 30 does not blow, system is operating properly at this time.
  19. Disconnect Driver Door Module (DDM) harness connector C521. Disconnect driver seat control switch harness connector C509. Measure resistance between ground and appropriate terminals at driver seat control switch harness connector C509. See DRIVER SEAT CONTROL SWITCH TERMINAL IDENTIFICATION table. If all resistance readings are 10,000 ohms or greater, replace driver door module. If any resistance readings are less than 10,000 ohms, repair short to ground in appropriate wire.
    DRIVER SEAT CONTROL SWITCH TERMINAL IDENTIFICATION

    Terminal No. Wire Color
    1 Yellow/White
    2 Red/Light Blue
    3 Yellow/Light Blue
    9 Red/White
    11 Yellow/Light Green
    12 Red/Light Green
    13 Gray
    14 Gray/Black
  20. Remove maxi-fuse No. 8 (30-amp) from power distribution box. Measure voltage at input side of maxi-fuse No. 8 at power distribution box. If battery voltage exists, go to next step. If battery voltage does not exist, repair power supply to maxi-fuse No. 8.
  21. Ensure maxi-fuse No. 8 is still removed. Remove fuse No. 30 (7.5-amp) from instrument panel fuse box. Disconnect Driver Seat Module (DSM) harness connector C337. Measure resistance in Red wire between output side of maxi-fuse No. 8 and input side of fuse No. 30. If resistance is 5 ohms or less, go to next step. If resistance is greater than 5 ohms, repair open in Red wire.
  22. Measure resistance between ground and output side of maxi-fuse No. 8 at power distribution box. If resistance is 10,000 ohms or greater, replace driver door module. If resistance is less than 10,000 ohms, repair short to ground in Red wire.