LEMON Manuals: Even more car manuals for everyone

Test C: Driver Seat Completely Inoperative

NOTE: After any repairs are complete, ensure all components are properly installed, all harness connectors are connected properly and repeat data link diagnostic test.
NOTE: Connectors C316, C317, C331, C360 and C362 are 2-terminal connectors. Identify connector by wire color. See WIRING DIAGRAMS  .
  1. Check For Driver Door Module (DDM) DTCs  - Retrieve DTCs from DDM. If DTC B1545 was not retrieved, go to next step. If DTC B1545 is retrieved, go to step 4).
  2. Check For Driver Seat Module (DSM) DTCs  - Retrieve DTCs from DSM. If no DSM DTCs were retrieved, go to next step. If any DSM DTCs were retrieved, perform appropriate test or go to appropriate step. See DSM DTC TEST table.
    DSM DTC TEST

    DTC Perform
    B1663  Step 16)
    B1663 & B1957 TEST E 
    B1663 & B1954 TEST E 
    B1664  Step 18)
    B1664 & B1953 TEST E 
    B1664 & B1950 TEST E 
    B1665  Step 20)
    B1665 & B1965 TEST E 
    B1665 & B1952 TEST E 
    B1666  Step 22)
    B1666 & B1961 TEST E 
    B1666 & B1958 TEST E 
    B1663, B1664, B1665 & B1666  Step 8)
    B1663, B1664, B1665, B1666 & B1667 TEST E 
  3. Check Driver Seat Control Switch Inputs To DDM  - Connect NSG tester to data link connector. Turn ignition switch to RUN position. Monitor DDM PIDs SFWD_SW, SREAR_SW, SFNT_SW and SRCL_SW while activating driver seat control switch in all directions. If DDM PID values do not agree with driver seat control switch position, go to next step. If DDM PID values agree with driver seat control switch position, go to step 8).
  4. Check Driver Seat Control Switch  - Remove driver seat control switch. Test driver seat control switch. See SEAT CONTROL SWITCH  under COMPONENT TESTS. If switch is okay, go to next step. If switch is defective, replace driver seat control switch.
  5. Check Power Supply At Driver Seat Control Switch  - Measure voltage at terminal No. 6 (Black/White wire) at driver seat control switch harness connector C520. If battery voltage exists, go to next step. If battery voltage does not exist, repair open in Black/White wire.
  6. Check For Short To Voltage  - Disconnect DDM harness connector C506. Measure for voltage between ground and appropriate terminals at DDM harness connector C506. See DDM HARNESS CONNECTOR C506 TERMINAL IDENTIFICATION  table. If voltage does not exist at any terminal, go to next step. If voltage exists at any terminal, repair short to voltage in appropriate wire.
    DDM HARNESS CONNECTOR C506 TERMINAL IDENTIFICATION

    Terminal No. Wire Color
    2 Red/White
    3 Red/Light Green
    4 Red/Light Blue
    5 Gray
    7 Yellow/White
    8 Yellow/Light Green
    9 Yellow/Light Blue
    10 Gray/Black
  7. Check For Open  - Ensure DDM harness connector C506 and driver seat control switch harness connector C520 are still disconnected. Measure resistance between appropriate terminals. See DDM CIRCUIT RESISTANCE  table. If all resistance readings are less than 5 ohms, replace driver door module. If any resistance readings are 5 ohms or greater, repair open in appropriate wire.
    DDM CIRCUIT RESISTANCE

    DDM Terminal No. Switch Terminal No. Wire Color
    1 3 Red/Light Green
    2 8 Yellow/Light Green
    3 5 Gray
    4 10 Gray/Black
    5 4 Red/Light Blue
    6 9 Yellow/Light Blue
    7 2 Red/White
    8 7 Yellow/White
  8. Check Driver Seat Operation  - Operate driver seat in all directions. If driver seat does not move in one-second intervals, go to next step. If driver seat moves in one-second intervals, perform TEST E: SEAT MOTORS OPERATE IN ONE-SECOND INTERVALS  .
  9. Check DSM Outputs  - Place transmission in Park. Select DSM active command DRIVER SEAT CONTROL on scan tool. Using scan tool, operate driver seat in all directions. If driver seat responds correctly, replace driver seat module. If driver seat does not respond correctly, go to appropriate step. See DRIVER SEAT MALFUNCTION  table.
    DRIVER SEAT MALFUNCTION

    Malfunction Perform
    No Seat Movement Next Step
    No Front Motor Movement Step 16)
    No Rear Motor Movement Step 18)
    No Horizontal Motor Movement Step 20)
    No Recline Motor Movement Step 22)
  10. Check Voltage To DSM  - Disconnect DSM harness connector C362. Measure voltage at terminal No. 1 (Red wire) at DSM harness connector C362. If battery voltage exists, go to next step. If battery voltage does not exist, repair open in Red wire.
  11. Check Black Wire For Open  - Measure resistance between ground and terminal No. 2 (Black wire) at DSM harness connector C362. If resistance is less than 10,000 ohms, go to next step. If resistance is 10,000 ohms or greater, repair open in Black wire.
  12. Check DSM Internal Fuse  - Remove DSM internal fuse (30-amp). If fuse is blown, go to next step. If fuse is okay, replace driver seat module.
  13. Check For Short To Ground  - Ensure transmission is in Park. Disconnect DSM harness connector C361, driver seat front height motor harness connector C316, driver seat rear height motor harness connector C317 and driver seat horizontal motor harness connector C360. Measure resistance between ground and appropriate terminals at DSM harness connector C361. See DSM CIRCUIT RESISTANCE  table. If all resistance readings are 10,000 ohms or greater, go to next step. If any resistance reading is less than 10,000 ohms, repair short to ground in appropriate wire(s).
    DSM CIRCUIT RESISTANCE

    Terminal No. Wire Color
    4 Yellow/White
    5 Yellow/Light Green
    6 Yellow/Light Blue
    11 Red/Light Blue
    13 Red/Light Green
    14 Red/White
  14. Check For Short To Ground  - Disconnect recline motor harness connector C331. Measure resistance between ground and terminal No. 7 (Gray/Black wire), then between ground and terminal No. 16 (Gray wire) at DSM harness connector C361. If both resistance readings are 10,000 ohms or greater, go to next step. If either resistance reading is less than 10,000 ohms, repair short to ground in appropriate wire(s).
  15. Check Recline Motor For Short To Ground  - Connect driver recline motor harness connector C331. Connect DSM harness connector C361. Ensure all other driver seat motors are still disconnected. Replace DSM internal fuse. Using power seat control switch, recline driver seat back completely backward and forward. If DSM internal fuse does not blow, replace driver seat track assembly. If DSM internal fuse blows, replace recline motor.
  16. Check Front Height Motor Operation  - Disconnect driver seat front height motor harness connector C316. Select DSM active command DRIVER SEAT CONTROL on scan tool. Measure voltage between terminals No. 1 (Red/Light Blue wire) and No. 2 (Yellow/Light Blue wire) at driver seat front height motor harness connector C316. Using scan tool, operate driver seat front height motor up and down. If voltage exists only when motor is commanded on, replace driver front seat track assembly. If voltage does not exist when motor is commanded on, go to next step.
  17. Check For Open  - Disconnect DSM harness connector C361. Measure resistance in Red/Light Blue wire between terminal No. 11 at DSM harness connector C361 and terminal No. 1 at driver seat front height motor harness connector C316. Also, measure resistance in Yellow/Light Blue wire between terminal No. 6 at DSM harness connector C361 and terminal No. 2 at driver seat front height motor harness connector C316. If both resistance readings are less than 5 ohms, replace driver seat module. If either resistance reading is 5 ohms or greater, repair open in appropriate wire(s).
  18. Check Rear Height Motor Operation  - Disconnect driver seat rear height motor harness connector C317. Select DSM active command DRIVER SEAT CONTROL on scan tool. Measure voltage between terminals No. 1 (Red/Light Green wire) and No. 2 (Yellow/Light Green wire) at driver seat rear height motor harness connector C317. Using scan tool, operate driver seat rear height motor up and down. If voltage exists only when motor is commanded on, replace driver front seat track assembly. If voltage does not exist when motor is commanded on, go to next step.
  19. Check For Open  - Disconnect DSM harness connector C361. Measure resistance in Red/Light Green wire between terminal No. 13 at DSM harness connector C361 and terminal No. 1 at driver seat rear height motor harness connector C317. Also, measure resistance in Yellow/Light Green wire between terminal No. 5 at DSM harness connector C361 and terminal No. 2 at driver seat rear height motor harness connector C317. If both resistance reading are less than 5 ohms, replace driver seat module. If either resistance reading is 5 ohms or greater, repair open in appropriate wire(s).
  20. Check Horizontal Motor Operation  - Disconnect driver seat horizontal motor harness connector C360. Select DSM active command DRIVER SEAT CONTROL on scan tool. Measure voltage between terminals No. 1 (Red/White wire) and No. 2 (Yellow/White wire) at driver seat horizontal motor harness connector C360. Using scan tool, operate driver seat horizontal motor forward and backward. If voltage exists only when motor is commanded on, replace driver front seat track assembly. If voltage does not exist when motor is commanded on, go to next step.
  21. Check For Open  - Disconnect DSM harness connector C361. Measure resistance in Red/White wire between terminal No. 14 at DSM harness connector C361 and terminal No. 1 at driver seat horizontal motor harness connector C360. Also, measure resistance in Yellow/White wire between terminal No. 4 at DSM harness connector C361 and terminal No. 2 at driver seat horizontal motor harness connector C360. If both resistance readings are less than 5 ohms, replace driver seat module. If either resistance reading is 5 ohms or greater, repair open in appropriate wire(s).
  22. Check Recline Motor Operation  - Disconnect drive seat recline motor harness connector C331. Select DSM active command DRIVER SEAT CONTROL on scan tool. Measure voltage between terminals No. 1 (Gray wire) and No. 2 (Gray/Black wire) at driver seat recline motor harness connector C331. Using scan tool, operate driver seat recline motor forward and backward. If voltage exists only when motor is commanded on, replace driver front seat track assembly. If voltage does not exist when motor is commanded on, go to next step.
  23. Check For Open  - Disconnect DSM harness connector C361. Measure resistance in Gray wire between terminal No. 16 at DSM harness connector C361 and terminal No. 1 at driver seat recline motor harness connector C331. Also, measure resistance in Gray/Black wire between terminal No. 7 at DSM harness connector C361 and terminal No. 2 at driver seat recline motor harness connector C331. If both resistance readings are less than 5 ohms, replace driver seat module. If either resistance reading is 5 ohms or greater, repair open in appropriate wire(s).