LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2020 >> NX 300h Base >> Repair and Diagnosis >> Engine Performance >> Fuel Delivery >> Fuel System (Service Information) >> Fuel Injector >> Inspection [10/2014 - ] >> Procedure

Inspection [10/2014 - ]: Procedure

  1. INSPECT FUEL INJECTOR ASSEMBLY 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 - 2 20°C (68°F) 11.6 to 12.4 Ω

      If the result is not as specified, replace the fuel injector assembly.

    2. Inspect the injector injection volume.
      WARNING:

      Keep the injector away from sparks during the test.

      1. Remove the No. 1 fuel pipe clamp from the fuel tube sub-assembly.
      2. Disconnect the fuel tube sub-assembly from the fuel pipe.

        Refer to PRECAUTION [10/2014 - 05/2019] Refer to PRECAUTION [05/2019 - ]

      3. Connect SST (fuel tube connector) to SST (hose) with SST (hose band), and then connect them to the fuel pipe (vehicle side).
        GTY517446Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a SST (Hose)
        *b SST (Hose Band)
        *c SST (Fuel Tube Connector)
        *d Fuel Pipe (Vehicle Side)
        • SST: 09268-31014 
          1. 09268-41700
          2. 95336-08070
        • SST: 09268-00010 
          1. 09268-00030
      4. Install the O-ring to the fuel injector assembly.
      5. Connect SST (adapter and hose) to the fuel injector assembly, and hold the fuel injector assembly and union with SST (hose band).
        GTY518626Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *1 O-Ring
        *a SST (Hose)
        *b SST (Hose Band)
        *c SST (Adapter)
        *d SST (Clamp)
        *e Vinyl Tube
        • SST: 09268-31014 
          1. 09268-41110
          2. 09268-41300
          3. 09268-41700
          4. 95336-08070
      6. Pass SST (tie band) through the loop on the handle of SST (clamp) to secure SST (clamp) to SST (adapter) as shown in the illustration.
        • SST: 09268-31014 
          1. 09268-41800
        GTY506772Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a SST (Tie Band)
        *b Lock
        NOTE:
        • As SST (tie band) does not completely prevent SST (clamp) from becoming loose, do not subject the parts to any impacts while using them.
        • Before using SST (tie band), make sure that there is no deterioration, damage or cracks. If there are any abnormalities, replace SST.

        HINT: 

        When removing SST (tie band), disengage the lock clamps.

      7. Check that SST (clamp) and SST (adapter) cannot be easily separated.
      8. Install a vinyl tube to the fuel injector assembly.
        NOTE:

        Install a suitable vinyl tube to the fuel injector assembly to contain any gasoline spray.

      9. Put the fuel injector assembly into a graduated cylinder.
      10. Operate the fuel pump.
      11. Connect SST (EFI inspection wire H) to the fuel injector assembly and the battery for 15 seconds and measure the injection volume with the graduated cylinder. Test each injector 2 or 3 times.
        GTY506964Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a SST (EFI Inspection Wire H)
        Connect
        • SST: 09842-30080 

        Standard Injection Volume

        87 to 105 cc (5.3 to 6.4 cu. in.) every 15 seconds

        Difference between each fuel injector assembly

        18 cc (1.1 cu. in.) or less

        If the result is not as specified, replace the fuel injector assembly.

        NOTE:
        • Make sure that SST (EFI inspection wire H) is securely connected.
        • Always do the switching at the battery side.
    3. Check for fuel drop.
      1. In the condition above, disconnect the tester probes of SST (EFI inspection wire H) from the battery and check for fuel drop from the fuel injector assembly.

        Standard fuel drop

        1 drop or less per 20 minutes

        If fuel drop is not as specified, replace the fuel injector assembly.