LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2020 >> GS 350 Base, AWD >> Repair and Diagnosis >> Brakes >> Traction Control >> Brake Control System - Service Information >> Brake Actuator >> Installation [10/2015 - ] >> Procedure

Installation [10/2015 - ]: Procedure

  1. INSTALL NO. 5 BRAKE ACTUATOR BRACKET 
    1. Install the No. 5 brake actuator bracket with the bolt.

      Torque: 11 N*m (112 kgf*cm, 8 ft.*lbf) 

  2. INSTALL BRAKE ACTUATOR WITH BRACKET 
    1. Temporarily install the brake actuator assembly with bracket with the 2 bolts and nut.
      GTY676637Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:
      • Do not damage the brake lines.
      • Do not hold the brake actuator assembly with bracket by the connector.

      HINT: 

      Install the brake actuator with bracket while avoiding the brake lines.

    2. Tighten the 2 bolts and nut in the order shown in the illustration.

      Torque: 19 N*m (194 kgf*cm, 14 ft.*lbf) 

    3. Set each brake line in the correct position on thebrake actuator as shown in the illustration.
      GTY631019Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a From Front Master Cylinder
      *b From Rear Master Cylinder
      *c To Front Wheel Cylinder Assembly RH
      *d To Front Wheel Cylinder Assembly LH
      *e To Rear Wheel Cylinder Assembly RH
      *f To Rear Wheel Cylinder Assembly LH
    4. Temporarily install the 3 brake lines to the correct position on the brake actuator assembly as shown in the illustration.
      GTY668282Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Torque Wrench Fulcrum Length

      Specified tightening torque 

      Torque: 15.2 N*m (155 kgf*cm, 11 ft.*lbf) 

      NOTE:
      • Do not kink or damage the brake lines.
      • Do not allow the brake lines to twist and interfere with other parts or vehicle body during tightening.
      • Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

      HINT: 

      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Refer to PRECAUTION [10/2015 - ]

      • When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.378 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf).
    5. Type A:
      1. Connect the connector to the brake actuator assembly and lock the lock lever.
        GTY615314Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Lock the lock lever
        NOTE:
        • Make sure that the connector is locked securely.
        • Make sure that the actuator connector can be connected smoothly. Do not allow water, oil or dirt to enter the connector.
    6. Type B:
      1. Connect the connector to the brake actuator assembly and lock the lock lever.
        GTY788185Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Connect the connector
        Lock the lock lever
        NOTE:
        • Make sure that the connector is locked securely.
        • Make sure that the actuator connector can be connected smoothly. Do not allow water, oil or dirt to enter the connector.
  3. INSTALL REAR NO. 1 BRAKE TUBE 
    1. Using a union nut wrench, connect the rear No. 1 brake tube to the brake actuator assembly.
      GTY645596Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Torque Wrench Fulcrum Length

      Specified tightening torque 

      Torque: 19.5 N*m (199 kgf*cm, 14 ft.*lbf) 

      NOTE:
      • Do not kink or damage the rear No. 1 brake tube.
      • Do not allow the rear No. 1 brake tube to twist and interfere with other parts or vehicle body during tightening.
      • Do not allow any foreign matter such as dirt or dust to enter the rear No. 1 brake tube from the connecting parts.

      HINT: 

      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Refer to PRECAUTION [10/2015 - ]

      • When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.378 in.)): 17.2 N*m (175 kgf*cm, 13 ft.*lbf).
    2. Attach the clamp to install the rear No. 1 brake tube.
  4. INSTALL FRONT NO. 1 BRAKE TUBE 
    1. Using a union nut wrench, connect the front No. 1 brake tube to the brake actuator assembly.
      GTY646254Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Torque Wrench Fulcrum Length

      Specified tightening torque 

      Torque: 19.5 N*m (199 kgf*cm, 14 ft.*lbf) 

      NOTE:
      • Do not kink or damage the front No. 1 brake tube.
      • Do not allow the front No. 1 brake tube to twist and interfere with other parts or vehicle body during tightening.
      • Do not allow any foreign matter such as dirt or dust to enter the front No. 1 brake tube from the connecting parts.

      HINT: 

      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Refer to PRECAUTION [10/2015 - ]

      • When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.378 in.)): 17.2 N*m (175 kgf*cm, 13 ft.*lbf).
    2. Attach the clamp to install the front No. 1 brake tube.
  5. INSTALL FRONT NO. 3 BRAKE TUBE 
    1. Install the grommet of the front No. 3 brake tube to the body.
      NOTE:

      Make sure that the grommet is securely attached to the body.

    2. Hold the flexible hose in place with a wrench and connect the front No. 3 brake tube to the flexible hose using a union nut wrench.

      Specified tightening torque 

      Torque: 15.2 N*m (155 kgf*cm, 11 ft.*lbf) 

      NOTE:
      • Do not kink or damage the brake lines.
      • Do not allow the brake lines to twist and interfere with other parts or vehicle body during tightening.
      • Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

      HINT: 

      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Refer to PRECAUTION [10/2015 - ]

      • When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.378 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf).
      GTY613783Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Torque Wrench Fulcrum Length
    3. Using a union nut wrench, connect the front No. 3 brake tube to the brake actuator assembly.
      GTY622297Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Torque Wrench Fulcrum Length

      Specified tightening torque 

      Torque: 15.2 N*m (155 kgf*cm, 11 ft.*lbf) 

      NOTE:
      • Do not kink or damage the brake lines.
      • Do not allow the brake lines to twist and interfere with other parts or vehicle body during tightening.
      • Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

      HINT: 

      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Refer to PRECAUTION [10/2015 - ]

      • When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.378 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf).
    4. Attach the clamp to install the front No. 3 brake tube.
  6. INSTALL VACUUM HOSE ASSEMBLY 
    1. Connect the vacuum hose assembly to the brake vacuum check valve assembly, and slide the clip to secure it.
  7. INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY 

    Refer to INSTALLATION [10/2015 - ]

  8. INSTALL NO. 3 ENGINE ROOM RELAY BLOCK 
    1. Install the No. 3 engine room relay block with the bolt and nut.
      GTY679560Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Torque: 8.0 N*m (82 kgf*cm, 71 in.*lbf) 

  9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 
    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Refer to INITIALIZATION [10/2015 - ]

  10. BLEED BRAKE SYSTEM 

    Refer to PROCEDURE - Step 2

  11. INSTALL ENGINE ROOM SIDE COVER LH 
    1. Install the engine room side cover LH with the 2 clips.
  12. PERFORM YAW RATE AND ACCELERATION SENSOR ZERO POINT CALIBRATION AND STORE SYSTEM INFORMATION 

    Refer to CALIBRATION [10/2015 - ]

  13. PERFORM TEST MODE INSPECTION 

    Refer to TEST MODE PROCEDURE [10/2015 - ]

  14. INSPECT BRAKE ACTUATOR USING TECHSTREAM 

    Refer to ON-VEHICLE INSPECTION [10/2015 - ] 

  15. CHECK FOR AND CLEAR DTCS 

    Refer to DTC CHECK / CLEAR [10/2015 - ]